Front Panel Express
How about legends applied using ink filled engraving and holes and dimensions cut to order?
www.frontpanelexpress.com
See
http://home.san.rr.com/john1in2/back1.JPG
http://www.diyaudio.com/forums/showthread.php?s=&threadid=26763
How about legends applied using ink filled engraving and holes and dimensions cut to order?
www.frontpanelexpress.com
See
http://home.san.rr.com/john1in2/back1.JPG
http://www.diyaudio.com/forums/showthread.php?s=&threadid=26763
service
I recommend these guys often, they are great, if a tad expensive (but not for what you get.) However, when a problem comes up, their customer service is also great. There are only like 3 employees so they have their attention on your project. I had a scratched up panel and was able to work it out over a 2 emails. I would use them again, and again...
As for prices, the software does a price estimate based on size, thickness, number of holes, tool changes, and engraving. So download the software and check out the prices. You just click on file...price estimate or something to that effect.
I recommend these guys often, they are great, if a tad expensive (but not for what you get.) However, when a problem comes up, their customer service is also great. There are only like 3 employees so they have their attention on your project. I had a scratched up panel and was able to work it out over a 2 emails. I would use them again, and again...
As for prices, the software does a price estimate based on size, thickness, number of holes, tool changes, and engraving. So download the software and check out the prices. You just click on file...price estimate or something to that effect.
Bill Fitzpatrick said:About $35 bucks for an anodized, engraved and filled lettering, 3.5" high rack panel with a half dozen or so holes. Additional holes are cheap as is extra lettering. A real bargan if you ask me.
I would say nothing to complain about. It is a bargain.
Hi.
I'd just like to add that if you're in europe, this would be the place to go:
http://www.schaeffer-apparatebau.de
(They're probably the same, as the software looks equal)
I've used their services and everything went smooth.
One thing that they could improve was anodizing *after* the cutting so the edges would also be anodized, thus making the panels look more professional. I asked about this and they said that they didn't do it because there hadn't been demand for it.
Maybe if we all asked at the same time...
Guilherme.
I'd just like to add that if you're in europe, this would be the place to go:
http://www.schaeffer-apparatebau.de
(They're probably the same, as the software looks equal)
I've used their services and everything went smooth.
One thing that they could improve was anodizing *after* the cutting so the edges would also be anodized, thus making the panels look more professional. I asked about this and they said that they didn't do it because there hadn't been demand for it.
Maybe if we all asked at the same time...
Guilherme.
Indeed GUILHERME
they are the same. It's more expensive to anodize afterwards becausse now they have large plates and only have to cut some parts, otherwise they have to anodize all these small parts...
All the same I'm very happy with them I ordered plates op till 10mm
Front top back and under are all made by schaeffer
Ralph
they are the same. It's more expensive to anodize afterwards becausse now they have large plates and only have to cut some parts, otherwise they have to anodize all these small parts...
All the same I'm very happy with them I ordered plates op till 10mm
An externally hosted image should be here but it was not working when we last tested it.
Front top back and under are all made by schaeffer
Ralph
Take a look at www.emashineshop.com.
Not cheap if you only want one but they have a a number of different finshings avaiable including color anaodize, power coat, as well as different levels and types of surface textures.
Assuming you mean face plate and not back plate and don't need silkscreening then:
For a front plate with just holes for a switch, LED and four countersunk bolts, I found www.onlinemetals.com the best deal. You have to drill the holes yourself which isn't that hard if you work slow and careful. Then you need an afternoon of mindless labor with increasingly fine grades of wet&dry sand paper plus soap and water. I have no training in metal work, and damn little skill, but by going slow I ended up with a face plate has caused my amp to be mistaken for a high-end commercial unit.
Not cheap if you only want one but they have a a number of different finshings avaiable including color anaodize, power coat, as well as different levels and types of surface textures.
Assuming you mean face plate and not back plate and don't need silkscreening then:
For a front plate with just holes for a switch, LED and four countersunk bolts, I found www.onlinemetals.com the best deal. You have to drill the holes yourself which isn't that hard if you work slow and careful. Then you need an afternoon of mindless labor with increasingly fine grades of wet&dry sand paper plus soap and water. I have no training in metal work, and damn little skill, but by going slow I ended up with a face plate has caused my amp to be mistaken for a high-end commercial unit.
Cutting after anodizing - that's disappointing.
This being a DIY forum, you could anodize the plate yourself. It's not that difficult a process.
Tim Smith
Macon, GA
What???????
Hi Tim,
Can you please tell me more about this??????
I'm interested as you can see
Audiofanatic
tsmith1315 said:
This being a DIY forum, you could anodize the plate yourself. It's not that difficult a process.
Tim Smith
Macon, GA
Hi Tim,
Can you please tell me more about this??????
I'm interested as you can see
Audiofanatic
- Status
- This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button.
- Home
- Design & Build
- Parts
- Machined Face Plates