Hi,There is no online store. Have not "modernized". Please send an email to rjm003.geo at yahoo.com with your requests and I will send you a Paypal invoice for the total.
Richard
I'm trying to contact you with the email address you listed and cannot get it to work. can you check that?...same with your website.
cheers,
Kirk
It works, you just have to replace "at" with the "@" mark...
In other news I have all but run out of the original 2 uF Arcotronics MKP cap used for C3 in the VSPS300 and Phonoclone3 projects. I've already stocked up on a new MKS cap, but the price will increase from $5 a pair to $6 a pair as a result.
In other news I have all but run out of the original 2 uF Arcotronics MKP cap used for C3 in the VSPS300 and Phonoclone3 projects. I've already stocked up on a new MKS cap, but the price will increase from $5 a pair to $6 a pair as a result.
Change of version notice:
From today, shipping VSPS300 and Phonoclone 3 boards revised to "m" and "35c" versions, respectively.
There is very little that is changed. The main thing to address was the difficulty many people had in soldering some components. To this end,
- metal layer thickness reduced from 70 microns to 35 microns.
- thermal isolation applied to all solid fills
other changes,
- layout and silk screen markings adjusted to be more consistent between VSPS and Phonoclone boards
- boards are now finished in matt, rather than glossy, black
Richard
From today, shipping VSPS300 and Phonoclone 3 boards revised to "m" and "35c" versions, respectively.
There is very little that is changed. The main thing to address was the difficulty many people had in soldering some components. To this end,
- metal layer thickness reduced from 70 microns to 35 microns.
- thermal isolation applied to all solid fills
other changes,
- layout and silk screen markings adjusted to be more consistent between VSPS and Phonoclone boards
- boards are now finished in matt, rather than glossy, black
Richard
Kits are back!
Phonoclone Kit : $125 (10 availble) Set of two boards and components to populate.
VSPS 300 Kit : $117 (10 available) Set of two boards and components to populate.
Sapphire Kit : $113 (10 available) Set of two boards and components to populate.
Shipping next month.
Phonoclone Kit : $125 (10 availble) Set of two boards and components to populate.
VSPS 300 Kit : $117 (10 available) Set of two boards and components to populate.
Sapphire Kit : $113 (10 available) Set of two boards and components to populate.
Shipping next month.
Pre-ordered kits to everyone who's name is not "Joe" were shipped out today.
lolz
I was off in my estimate by 3 weeks, but anyhow: all 100 VSPS Stereo Kits have now been sold. A big thank you to everyone!
International breakdown of the shipped kits is as follows-
US 45
UK 8
Mexico 6
Australia 5
Germany 5
Canada 4
Italy 4
France 3
Netherlands 3
Brazil 2
Malaysia 2
Sweden 2
Belgium 1
Denmark 1
Finland 1
Ireland 1
Norway 1
Thailand 1
Spain 1
Serbia 1
Poland 1
Singapore 1
Lost in Transit 1
International breakdown of the shipped kits is as follows-
US 45
UK 8
Mexico 6
Australia 5
Germany 5
Canada 4
Italy 4
France 3
Netherlands 3
Brazil 2
Malaysia 2
Sweden 2
Belgium 1
Denmark 1
Finland 1
Ireland 1
Norway 1
Thailand 1
Spain 1
Serbia 1
Poland 1
Singapore 1
Lost in Transit 1
People have been asking after the Phonoclone 3 Kits. I give in: I'll go buy more resistors to be able to offer these again. Just give me a couple of weeks to sort it out. I'm also running low on boards, so may be a blackout there as well while I get more.
A couple of people ended up buying boards+parts rather than the kit - if you would like the resistors even if they arrive a bit late, please get in touch with me.
A couple of people ended up buying boards+parts rather than the kit - if you would like the resistors even if they arrive a bit late, please get in touch with me.
Last edited:
VSPS PCBs
Dear Richard,
I would like to purchase two PCBs, are they avaiable?
Regards
People have been asking after the Phonoclone 3 Kits. I give in: I'll go buy more resistors to be able to offer these again. Just give me a couple of weeks to sort it out. I'm also running low on boards, so may be a blackout there as well while I get more.
A couple of people ended up buying boards+parts rather than the kit - if you would like the resistors even if they arrive a bit late, please get in touch with me.
Dear Richard,
I would like to purchase two PCBs, are they avaiable?
Regards
I was off in my estimate by 3 weeks, but anyhow: all 100 VSPS Stereo Kits have now been sold. A big thank you to everyone!
International breakdown of the shipped kits is as follows-
US 45
UK 8
Mexico 6
Australia 5
Germany 5
Canada 4
Italy 4
France 3
Netherlands 3
Brazil 2
Malaysia 2
Sweden 2
Belgium 1
Denmark 1
Finland 1
Ireland 1
Norway 1
Thailand 1
Spain 1
Serbia 1
Poland 1
Singapore 1
Lost in Transit 1
Richard, where is Russia in your list? Mine received, could not be lost in transit
Phonoclone 35f and B-board 10e boards are finished and on their way to me. They are delayed as I was promised Feb 20 delivery.
Backordered Phonoclone 3 kits will ship out by next Monday at the latest. B-board kits perhaps a couple of days later, depending on a parts order I have with Mouser and, given this is the first batch, depending on any unforseen problems that might pop up.
Backordered Phonoclone 3 kits will ship out by next Monday at the latest. B-board kits perhaps a couple of days later, depending on a parts order I have with Mouser and, given this is the first batch, depending on any unforseen problems that might pop up.
B-board status update:
Boards check OK. Parts check OK. Sim checks OK.
Just need to build a couple to confirm that sim mirrors reality, and then we are good to go.
The trick here is setting the emitter resistors, since that's a thermal dependence and simulations aren't great modelling thermals. I want to make sure the measured bias currents are in line with what was predicted.
Boards check OK. Parts check OK. Sim checks OK.
Just need to build a couple to confirm that sim mirrors reality, and then we are good to go.
The trick here is setting the emitter resistors, since that's a thermal dependence and simulations aren't great modelling thermals. I want to make sure the measured bias currents are in line with what was predicted.
- Status
- This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button.
- Home
- Group Buys
- Phonoclone and VSPS Group Buys