Finally i finished my ZenV4.
Sound much better then ZenV2.
I use only a cap multiplier and no regulation.
V+ is 32V only and i`m using 0.15 ohm for the
currentsource and currentsensing.
No hum at all. A very nice Amp!!
I add a picture from my speaker in development.
Fostex FE103 and 4 cheap 22cm bass, all as
dipols. Sounds great!😀
This chaotic piece is the activ crossover (Zen type).
Andreas
Sound much better then ZenV2.
I use only a cap multiplier and no regulation.
V+ is 32V only and i`m using 0.15 ohm for the
currentsource and currentsensing.
No hum at all. A very nice Amp!!
I add a picture from my speaker in development.
Fostex FE103 and 4 cheap 22cm bass, all as
dipols. Sounds great!😀
This chaotic piece is the activ crossover (Zen type).
Andreas
Attachments
Good job! Certainly this kind of post keeps me encouraged to push ahead with my A2 project.
By the way, can you post details of your turntable?
By the way, can you post details of your turntable?
Congratulations!
It´s nice to some amps made of wood for a change.
Very clean and presice design, looks great.
I also like the p2p on veroboards!
🙂
It´s nice to some amps made of wood for a change.
Very clean and presice design, looks great.
I also like the p2p on veroboards!
🙂
Hallo gilid,
isn`t that good what it looks like.
Parts are from an old Lenco.
Sound of course better with my EMT TSD15 Tondose. 😎
Andreas
isn`t that good what it looks like.
Parts are from an old Lenco.
Sound of course better with my EMT TSD15 Tondose. 😎
Andreas
Andreas,
It looks like the little boy likes to play with this kind of stuff when he grows up. How old is he? Your son?
It looks like the little boy likes to play with this kind of stuff when he grows up. How old is he? Your son?
Clean, simple lines. Very nice! Pleasing on the eye as well as the ear. Your attention to the small details is quite obvious.
Well impressed,😎
Paul
Well impressed,😎
Paul
To Erik:
Sides are made of beechwood 27mm thick.
Bottom and top is made of beech multiplex.
All polished with hemp oil
To fcel:
Maurizio is my 20th month old son and very
interested in electronic parts(big caps, potis,
and he loves the oszi)
He enjoy music only when it sounds good otherwise
he shutdown the cd player 😉
He loves to hear my manger system - he hates
his small portable radio.
Thanx for your comments.
Andreas
Sides are made of beechwood 27mm thick.
Bottom and top is made of beech multiplex.
All polished with hemp oil
To fcel:
Maurizio is my 20th month old son and very
interested in electronic parts(big caps, potis,
and he loves the oszi)
He enjoy music only when it sounds good otherwise
he shutdown the cd player 😉
He loves to hear my manger system - he hates
his small portable radio.
Thanx for your comments.
Andreas
Q about placement of powersupply caps
I collect both powersupplycaps after the rectifier.
Is it an advantage to collect one of them
after the capmultiplier?
Since the aleph source dosn`t draw constant
current this could be an advantage,or not?
Andreas
I collect both powersupplycaps after the rectifier.
Is it an advantage to collect one of them
after the capmultiplier?
Since the aleph source dosn`t draw constant
current this could be an advantage,or not?
Andreas
very nice job.can you tell me about the chassis and the heat sink size.and about the amp. running temperature.Thank you!😎
Hallo David,
Chassis is 27 * 24 * 39 cm
Heatsink 22 * 22 * 8 cm
haven`t measure temp but should be 50C.
Andreas
Chassis is 27 * 24 * 39 cm
Heatsink 22 * 22 * 8 cm
haven`t measure temp but should be 50C.
Andreas
Very, Very neat look, good idea to have front corners rounded,
they give a great smooth looking front.😉
ciao,
Roberto
they give a great smooth looking front.😉
ciao,
Roberto
- Status
- Not open for further replies.