Hi,
I have a pair of Alpair 6P and a Pair of Alpair 6M on my table (both gen 2). I have to build two pairs of small BR speakers for my nephews (20-30cms height).
I was looking for alternativies to the small BR plans on Mark Audio site and obviously looking here.
I guess I should look at mfonken and ufonken cabinets, but I get lost.
I also remember there was the possibility to buy a collection of plans, but I cannot find the thread again.
can you address me?
Regards
northernsky
I have a pair of Alpair 6P and a Pair of Alpair 6M on my table (both gen 2). I have to build two pairs of small BR speakers for my nephews (20-30cms height).
I was looking for alternativies to the small BR plans on Mark Audio site and obviously looking here.
I guess I should look at mfonken and ufonken cabinets, but I get lost.
I also remember there was the possibility to buy a collection of plans, but I cannot find the thread again.
can you address me?
Regards
northernsky
Subscription info here http://www.diyaudio.com/forums/plan...10-hifi-minionken-plan-set-subscriptions.html
There are not all that many enclosures for these. A mMar-Ken for the A6p (same as the one posted for the original A6 but with no vent spacer. mMar-Ken6 with A6p is a near ideal volume and works really well.
The full plan-set includes this box, a CGR dmMar-Ken6.2m for the metal cone (+ the "same" box with a cross-section closer to square)and a uMar-Ken6 that fits either driver with no changes (+ similar with a regular circular vent), and a couple of examples of shoe-horning A6.2m into the smallest box possible. I have a mostly drawn trapezoid mMar-Ken6p with the vents up the side almost done.
Has some damping & cut plans.
email if you'd like to subscribe.
dave
There are not all that many enclosures for these. A mMar-Ken for the A6p (same as the one posted for the original A6 but with no vent spacer. mMar-Ken6 with A6p is a near ideal volume and works really well.
The full plan-set includes this box, a CGR dmMar-Ken6.2m for the metal cone (+ the "same" box with a cross-section closer to square)and a uMar-Ken6 that fits either driver with no changes (+ similar with a regular circular vent), and a couple of examples of shoe-horning A6.2m into the smallest box possible. I have a mostly drawn trapezoid mMar-Ken6p with the vents up the side almost done.
Has some damping & cut plans.
email if you'd like to subscribe.
dave
perhaps now redundant, but the "milli" design Dave referred to is
http://frugal-phile.com/boxlib/P10free/mMar-Ken6-1v0-map-231009.pdf
There will of course be limitations of the driver's excursion limits, but they work quite nicely and are a relatively simple build.
http://frugal-phile.com/boxlib/P10free/mMar-Ken6-1v0-map-231009.pdf
There will of course be limitations of the driver's excursion limits, but they work quite nicely and are a relatively simple build.
Thak you Chris.
I subscribed for the planet-10 plans and I am currently building
a pair of microMarken with A6P and a pair with A6M.
When I finish I'll be able to make a subjective comparison (also with my Fostex F103EN in factory BR).
northernsky
Hi Dave, its possibly a trapezoid mMar-Ken6p but with twin drivers? Im playing with the idea of put 2 in series (mainly because my amp was designed for 8 ohm drivers)... Thanks in advance...
PD: sorry for my bad english...
Nothing wrong with your English - better I suspect than Dave's Spanish - and often his hastily typing reads as if by a "C" grade ESL student
Yes, it is possible. It would be the same as any of the deciSize for A7/CHR/CHP/FF125wk retuned for twin A6p.
If you subscribe i'll do it for you. eMail me.
dave
If you subscribe i'll do it for you. eMail me.
dave
I took grade 11 math instead of Grade 10 typing -- at the time i said, when will i ever need to type.
dave
- Status
- Not open for further replies.