Hi,
I am encouraging myself in to DIY project 3way floorstander. There few interesting plans available and after searching I found Satorique 4 floorstander. All details are here, except for crossover, of course 🙂 Any one have any information of parts list for the crossover?
More details are here:
Speaker instructions 2019 | Loudspeakerbuilding
Thanks
I am encouraging myself in to DIY project 3way floorstander. There few interesting plans available and after searching I found Satorique 4 floorstander. All details are here, except for crossover, of course 🙂 Any one have any information of parts list for the crossover?
More details are here:
Speaker instructions 2019 | Loudspeakerbuilding
Thanks
I didn't read the whole website, but I guess this is a kit. If you want to build this, just get the kit from them to say thank you for developing the thing and you should get all the details and more about the x-over etc.
Link to kit purchase - Looks like a closed design you have to buy.
Satorique - Lautsprecher - Satorique4
Satorique - Lautsprecher - Satorique4
I know it is a kit, that would also be one option to just buy it. It is just that price for the drivers alone can be a found for a lot cheaper. But I guess development of this kit is accounted into the price also.
1400euro for a pair ?
19P is lile 150euro
13P is like 100euro
Tweeter like 100euro
So its like 150x4 for 19 = 600euro
100x4 for 13 = 400euro
100x2 for 29 = 200euro
+ crossover ?
It looks like a good price for kit ?
19P is lile 150euro
13P is like 100euro
Tweeter like 100euro
So its like 150x4 for 19 = 600euro
100x4 for 13 = 400euro
100x2 for 29 = 200euro
+ crossover ?
It looks like a good price for kit ?
I think the price on the site is for 1 speaker only given the addition for RD to Be tweeter is only 200Euro (approx price between 29RN and 29BN single unit).
You could use the crossover schematic as a basis for your own design and use Xsim/Boxsim/Vituix etc. to optimise, this would then be your design to own.
Here's an alternative using the WO24P bass drivers, has a published crossover so you can cost this up.
https://pbnaudio.com/wp-content/uploads/2019/08/PBN.SBA951_flyer2.pdf
You could use the crossover schematic as a basis for your own design and use Xsim/Boxsim/Vituix etc. to optimise, this would then be your design to own.
Here's an alternative using the WO24P bass drivers, has a published crossover so you can cost this up.
https://pbnaudio.com/wp-content/uploads/2019/08/PBN.SBA951_flyer2.pdf
Last edited:
I have some rough simulation using Vituixcad, the problem is because I can not find some frd and zma files for the drivers used in this kit, at least not from the same source so I can not be 100% sure of what I have simulated. But, in case any one have those files, I would be more that grateful if they can be shared.
I know that. But this is just rough aproximation and it can be a little different in reality. Also the graphs are probably smoothed too much and the scale is low. Not much of a help..
An externally hosted image should be here but it was not working when we last tested it.
It looks doable. I have used SPL plots from datasheets, so not necessarily 100% correct, baffle and driver positions are included. Comments welcome.
An version #2 which should be a little easier and better:
An externally hosted image should be here but it was not working when we last tested it.
