Steve, these jfets were matched by Nelson Pass and his team at Pass Labs.I received a “0.1mA matched quad” of 2SJ74 B grade JFETs today. They all were tossed in a bag only marked 6-8mA.
Leaves me wondering if they were actually tested and matched at a specific tight value per the stringent conditions noted on the Store description page.
More helpful information on this in our store's JFET matching information page:
https://diyaudiostore.com/pages/jfet-matching-information
Hi Erick, Whammy pcbs are expected to get re-stocked in two months. The full whammy kit, including the chassis, is shipped from the USA warehouse.Hi @Helpdesk ,
Is there any news on the Whammy PCB coming back into stock? Also, Does the Whammy chassis drop ship from Modushop or from the store in the US?
Warm regards
Erick
A.L.C., the store Helpdesk does not have the technical know-how to answer this query adequately. Please post your query in the Elekit thread:
https://www.diyaudio.com/community/threads/elekit-tu-8200r.336262/page-13#post-7199696
https://www.diyaudio.com/community/threads/elekit-tu-8200r.336262/page-13#post-7199696
You're spoiled for choice for unmatched LSK170. Mouser of course, but https://store.nacsemi.com/products/search?part=lsk170 has the best prices, in all gain grades and packages.
hello all,
i am looking for a entry point into electronics and was looking at the amp camp 1.8. I have turned a pair of M-audio AV40 speakers into passive speakers and they currently use speaker wire from a philips receiver(..or is this a amp? it used to be used with a sound bar and a bluetooth sub woofer) and its connected to a HDMI out signal from my PC/graphics card.
If i buy the amp camp, can i use all my existing hardware with adapters?
should i use audio out by that 3.5 jack on my motherboard or continue to use HDMI with a amp camp?
Can i use speaker wire with the AV40 speakers? I think these are 4 ohm
i am looking for a entry point into electronics and was looking at the amp camp 1.8. I have turned a pair of M-audio AV40 speakers into passive speakers and they currently use speaker wire from a philips receiver(..or is this a amp? it used to be used with a sound bar and a bluetooth sub woofer) and its connected to a HDMI out signal from my PC/graphics card.
If i buy the amp camp, can i use all my existing hardware with adapters?
should i use audio out by that 3.5 jack on my motherboard or continue to use HDMI with a amp camp?
Can i use speaker wire with the AV40 speakers? I think these are 4 ohm
Big upgrade and refresh Should be up later today, or at latest tomorrow.
EDIT: We are shooting to be back up at 4AM UTC on Monday 3rd July 2023.
EDIT: We are shooting to be back up at 4AM UTC on Monday 3rd July 2023.
Last edited:
Hello,
I purchased 2 sets of matched quads (Toshiba 2SJ74 Quad 8-11mA and Toshiba 2SK170/2SJ74 Quad 8-11mA) from the store a while back. When I checked this week for use in a project they no longer seem to match. I followed the store's JFET matching information page to check. Is it possible for the JFETs go out of match? Any help would be appreciated.
Regards,
Subbu
I purchased 2 sets of matched quads (Toshiba 2SJ74 Quad 8-11mA and Toshiba 2SK170/2SJ74 Quad 8-11mA) from the store a while back. When I checked this week for use in a project they no longer seem to match. I followed the store's JFET matching information page to check. Is it possible for the JFETs go out of match? Any help would be appreciated.
Regards,
Subbu
A member would like to confirm a part received with an ACA kit, and has started this thread - https://www.diyaudio.com/community/threads/aca-mini-potentiometer-pins.401831/
Hi Woody. The ACA mini kits are dispatched and stored in our shipper's warehouse as complete units and we have no access to them. Regrettably, we cannot sell individual components separately. If you have any further inquiries, feel free to email the Helpdesk directly at contact@diyaudiostore.com
- Home
- The diyAudio Store
- General diyAudio store questions thread