6V6 Behavior W/Fixed Bias (SE Amp) - diyAudio
Go Back   Home > Forums > Amplifiers > Tubes / Valves

Tubes / Valves All about our sweet vacuum tubes :) Threads about Musical Instrument Amps of all kinds should be in the Instruments & Amps forum

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 12th September 2010, 04:12 PM   #1
kevinkr is offline kevinkr  United States
diyAudio Moderator
 
kevinkr's Avatar
 
Join Date: Sep 2004
Location: Boston, Massachusetts
Blog Entries: 6
Default 6V6 Behavior W/Fixed Bias (SE Amp)

Under "text book" conditions for a plate and screen voltage of 250V, and a grid bias of -12V the supposed plate current is approximately 42 mA with a screen current of around 3mA. This is more or less what you'd find right out of any RCA Radiotron data book.

Simulations in Spice produce the expected plate and screen current under the above stated conditions..

When I actually designed and finally built the amplifier, the current I actually get with -12V grid bias is about 1/3 of that predicted. No big deal except that my bias supplies are 12V camera batteries (A23), and therefore not readily adjustable. (9V batteries should in theory result in too much plate current, but I could reduce the screen voltage to compensate at the expense of lost open loop gain)

I've not designed much with the 6V6 - this is actually my first SE pentode amp design ever ( what's the world coming to ) and was somewhat surprised that the stated conditions are no where close to what I am measuring in the amplifier. The tubes are used Kenrad 6V6GT and are consistent channel to channel, and test good. I also have a pair of GE 6V6GT and will evaluate them next. This is not a small difference from the stated expectations for the given conditions but at least 300% off the mark. (I'd not have been surprised at 50% or so, but these aren't semiconductors...)

My thoughts are to drop the bias battery voltage with resistive divider which unfortunately does mean that they will have to be replaced from time to time. (I'll just replace the current grid resistor with the thevenin equivalent divider network that gives me the right voltage. Unfortunately this will kill the batteries rather quickly. A few months and they would have to be replaced. - I may use an opto isolator driven by the filament supply to ground one end of the bias string. Fail safe)

Interestingly reducing the bias to -11V at the grid had an insignificant effect - the plate current increased by less than 25%. I think I need to have another look at the characteristic curves as this is not adding up.. (large change in the slope of the transconductance as the current goes up?)

The amplifier is a simple pentode with a 6J7 driver, and internal local feedback. (6V6 plate to 6J7 cathode - it's not too different than a classic design floating around on the web) The amp has fixed bias in the output stage and had screen regulation as well which is currently disabled.

It looks like I should have found the space for a conventional bias supply and a set of pots for bias adjustment. (I actually have an idea how I can derive the bias supply if needed from the existing plate supply and it would be self compensating..)

Transconductance must be all over the place with these types for them to not even come close to matching the data book operating point under nearly identical conditions.

I'm going to use a couple of regulated supplies and determine empirically just what conditions are required to get the stated plate current at 250V on the plate.

Anyone have any useful thoughts? George, Wavebourn?
__________________
"Extraordinary claims require extraordinary evidence." - Carl Sagan

Last edited by kevinkr; 12th September 2010 at 04:28 PM.
  Reply With Quote
Old 12th September 2010, 04:48 PM   #2
Yvesm is offline Yvesm  France
diyAudio Member
 
Yvesm's Avatar
 
Join Date: Jul 2004
Location: Ardeche
Hi,

I did that:
Click the image to open in full size.



Yves.
  Reply With Quote
Old 12th September 2010, 08:18 PM   #3
athos56 is offline athos56  United States
diyAudio Member
 
athos56's Avatar
 
Join Date: May 2006
Location: Yakima, Washington
This is an interesting thread. I have some parts set aside for a SE 6V6 amp. Could we see the original schematic? Yves, I always like the looks of your amps, there's always something I don't get or haven't seen, in this case the ECC812 tube, whats it like?
  Reply With Quote
Old 12th September 2010, 08:34 PM   #4
kevinkr is offline kevinkr  United States
diyAudio Moderator
 
kevinkr's Avatar
 
Join Date: Sep 2004
Location: Boston, Massachusetts
Blog Entries: 6
Athos, I'll draw up a schematic once I have something that actually works and post it here.. In the mean time I'm hoping someone will weigh in w.r.t my original comments about the correlation between published specification and bench measurements of the 6V6 because frankly they don't seem to. (At least for this particular pair??)

After I finish lunch (just got back from the rink and our Sunday afternoon ice dance lesson) I will head downstairs, play some music and set up for some serious bench measurements.

Yves, very interesting design that incorporates some similar features although implementation is very different. In fact your bias source is exactly what I was planning to do as a last desperate act - with regulated screens I should be able to use battery derived fixed bias, without probably somewhat ill-advised. (I won't regulate the bias in that case)

Your numbers do seem to imply that there might be something odd about those Kenrad tubes I'm using - so I will swap them out. (Your stated operating point is very close to mine)
__________________
"Extraordinary claims require extraordinary evidence." - Carl Sagan

Last edited by kevinkr; 12th September 2010 at 08:37 PM.
  Reply With Quote
Old 12th September 2010, 08:39 PM   #5
Yvesm is offline Yvesm  France
diyAudio Member
 
Yvesm's Avatar
 
Join Date: Jul 2004
Location: Ardeche
Glad you like it !
ECC812 looks very like an ECC85, something in between a 12AT7 and a 6BQ7.

Yves.


Hi Kevin, cross posting
I fear your tubes are not in mint condition . . .
I've built at least 3 samples of this amp with various 6V6, from old coke bottle to tubular shape with almost the same working point.

Last edited by Yvesm; 12th September 2010 at 08:47 PM.
  Reply With Quote
Old 12th September 2010, 10:32 PM   #6
diyAudio Member
 
Joshua_G's Avatar
 
Join Date: Nov 2008
Location: Small village, Israel
Kevin, it looks like the discrepancy between the text book condition for the grid bias and the actual results you got should be looked at. There may be something wrong with the tube(s) you use. Else, it doesn't make sense.

Yves, I'd use a separate winding, or separate trafo for the negative bias supply. A 12-15 Volt trafo with low current consumption isn't expansive.
I'd also prefer LC or CLC HT filter, rather than CRC.
  Reply With Quote
Old 13th September 2010, 02:41 AM   #7
diyAudio Member
 
tubelab.com's Avatar
 
Join Date: Jul 2005
Location: West Virginia panhandle
Quote:
Anyone have any useful thoughts? George, Wavebourn?
No thoughts, but real measurements.

I took a Simple SE which is cathode biased. I ran it on an external power supply in triode mode. I set the power supply for 262 volts on the plate of the tubes and then tweaked the cathode resistors for 12 volts on the cathode. This leaves the desired 250 volts across the tubes. The cathode resistors wound up at 280 ohms (two 560's in parallel). That gives me 43 mA for plate and screen which is close to the data sheet values. I tried NOS GE, NOS wafer based Sylvania, NOS green lettered Sylvania, and my favorites the grey glass RCA's. All were within 0.5 volts of 12 V.

I usually run 6V6's a bit hotter, OK quite a bit hotter, but this seems to sound pretty good. I think it sounded better when I used the little Edcor OPT's, but that was almost 2 years ago. I have Transcendars in there now. Both watts were straining to squeeze their sound out of my 88db Yamaha speakers, but I will revisit this combination when I get my horn speakers finished!

OH, yeah while I was at it I dropped in a pair of $1 tubes. The current went up to 57 mA (expected) and the sound got fatter with more bass. Maybe I will just turn the power supply up a bit.......
__________________
Too much power is almost enough! Turn it up till it explodes - then back up just a little.
  Reply With Quote
Old 13th September 2010, 03:53 AM   #8
diyAudio Member
 
Join Date: Oct 2004
Location: Adelaide South Oz
The local feedback arrangement you are using from 6V6 anode to 6J7 cathode MAY be responsible for the difference from book value you are seeing. With this feedback my quick trigger pull guess (haven't worked thru' the math) is that you are trading 6V6 gm for reduced rp - so of course the bias point will change. The feedback has reduced the gm to 1/3 so at book value bias you get 1/3 the idle current you expected. If your local feedback level is 10.5dB (a quick compare of open and closed loop gain will tell you what it is) then this is exactly what I would expect to see.

Cheers,
Ian
  Reply With Quote
Old 13th September 2010, 05:49 AM   #9
kevinkr is offline kevinkr  United States
diyAudio Moderator
 
kevinkr's Avatar
 
Join Date: Sep 2004
Location: Boston, Massachusetts
Blog Entries: 6
Thanks for all of the responses. I'm on new ground here, and making some significant mis-steps as you'll see below.

Turns out the bloody thing was finding more than a few ways to oscillate and that is why nothing made any sense. Anyway after fixing the myriad oscillation problems mostly in the 6J7 based driver stages I did in fact find out that my 12V batteries with a modicum of cathode bias (~0.5V) did in fact put me in the ball park.

Lots of problems overall with this pentode driven pentode output stage, but most have been worked out at this point.

Lesson learned: At first sign of trouble scope everything!

And because I was concerned about stability I loaded the secondaries of the OPTs prior to starting the bench work. Good thing I did, probably would have fried them otherwise.

I'm going to crank a little more current through the tubes to see whether or not I can achieve more than a couple of watts at acceptable distortion. This I will do mainly by switching to a more efficient rectifier tube. (Intended to use 5Y3, oddly sole example was bad - using 5U4GTB instead, probably will use a nice GZ32 I have on hand for some extra voltage.)

So what I have right now is a design with CRCLC filter with the output of the CRC section feeding the plates of the 6V6s, and the output of the LC feeding the 6V6 screens and plates/screens of the 6J7s.

I'm probably going to apply some overall feedback as well as I have a little gain to burn and need to drop the 120Hz buzz at the output by at least 6dB and I am reaching the point of diminishing returns on the psu side. (I could replace the 200 ohm resistor in the CRC with an L if I can find one that is physically reasonably sized and has a H or so of inductance at ~120mA or so..) The inductor is good for a couple of additional dB of buzz reduction on the output. Right now I measure 7mVrms which is far more than I am willing to tolerate. I'd be happy with <3mV although I generally target <1mVrms.

More when I next work on this.. It strikes me that this might not be a great design for anyone else to build although I will share it once I am sure it does not blow up.. (at least)

I think the main problem with this design is actually the pentode driver.

Sonically speaking I have no idea what to expect. Sine waves look fine..
__________________
"Extraordinary claims require extraordinary evidence." - Carl Sagan

Last edited by kevinkr; 13th September 2010 at 05:56 AM.
  Reply With Quote
Old 13th September 2010, 06:23 AM   #10
diyAudio Member
 
Wavebourn's Avatar
 
Join Date: Sep 2006
Location: Pleasant Hill, CA
Send a message via Skype™ to Wavebourn
I was away from my computer the whole day today, so did not see your first post, sorry. It is great you've found the cause of strange behaviour!
I can't find that archive of files for 6V6 that contained nice anode curves with variable G2 voltage, but I remember I was going to try it with something like 10-12K load, about 450V B+, and something between 150 and 200V on G2. It looked nice on the paper.
__________________
The Devil is not so terrible as his math model is!
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Simple SE with CCS and fixed bias boywonder Tubes / Valves 0 21st February 2009 04:40 AM
Finding bias point in PP fixed bias beamnet Tubes / Valves 14 7th December 2008 01:25 PM
Battery grid bias to fixed bias in Toccato? w00t Tubes / Valves 3 2nd December 2007 12:34 AM
Odd's n Ends Revisited 6V6 SE amp Sparky OR Tubes / Valves 2 10th March 2006 06:54 AM
turning a SE 6v6 to a 6bq5 amp rvas18 Tubes / Valves 25 8th January 2004 06:29 PM


New To Site? Need Help?

All times are GMT. The time now is 07:06 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2