Distortion Tests - HifimeDIY T2 / LJM L20D / SURE TDA7498 - diyAudio
Go Back   Home > Forums > Amplifiers > Class D

Class D Switching Power Amplifiers and Power D/A conversion

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 14th August 2011, 07:11 PM   #1
trevmar is offline trevmar  United States
diyAudio Member
 
Join Date: Jan 2011
Default Distortion Tests - HifimeDIY T2 / LJM L20D / SURE TDA7498

I have run harmonic-distortion vs frequency and distortion vs output-power tests on the three switching amplifier boards I have bought in the last couple of months.

For the HifimeDIY T2, I connected a Meanwell (clone) 27V 5A supply, and a dummy load which is configurable to both 4 and 8 ohms.
I measured Harmonic Distortion vs Frequency at about 4 watts output power into 8 ohms. Excellent results -- with distortion over most of the spectrum ranging between 0.1% (-60dB) and 0.3% (-50dB). I repeated this at 35 watts power level, and a respectable half a percent (approx) of distortion was maintained nicely over the usable audio range. Using a 1KHz tone, I then ran Distortion vs Output Power with an 8 ohm load (attachment 3) and also with a 4 ohm load. Very good results, even with the 4 ohm load (remember that -40dB = 1% distortion). The T2 is a nice, clean, little amplifier, especially at 8 ohms.

I then tested ljm_ljm's new L20D amplifier, which uses the IRS2092 delta-sigma modulation chip for PWM conversion. For a power supply I used a toroidal transfomer rated at 28VAC 100watts, with 88,000 uF of filter capacitors. The results with the L20D were nothing short of superb. Many linear amplifiers would be struggling to achieve such a high linearity, especially at the high power levels the L20D can handle. Attachment 5 is distortion vs frequency into 8 ohms, at 35 watts output level. There is no point in showing lower output powers, the L20D is exceptional throughout its whole power range. I repeated that sweep for a 4 ohms load. Attachment 7 shows distortion vs output power into an 8 ohm load. Even putting out over 100W into a 4 ohm load (attachment 8), the L20D generated virtually no harmonic distortion. Everything was right at the lower limit of my test setup, less than 0.1% over every reasonable operating condition. I can see why ljm_ljm was so excited when he finished his L20D board

So now to the new SURE 100W+100W board using the new(ish) TDA7498 chip. This board was unstable when it arrived, and I had to add Zobel damping to the output network (described in another thread). Attachment 9 shows that the harmonic distortion, even at 4W into 8 ohms, is unacceptably high, hovering just below 1%. Similarly, the distortion vs power curve was not even close to that of the T2 or the L20D.

I haven't tested InterModulation distortion for these amplifiers yet, I should find time to do that sometime this week. I also will try and figure out exactly how SURE managed to mess up their TD7498 design so completely...
Attached Images
File Type: gif DistF_T2_8ohm_5r4Vrms.gif (14.8 KB, 5022 views)
File Type: gif DistF_T2_8ohm_17Vrms.gif (15.1 KB, 4931 views)
File Type: gif Pdist_T2_8ohm_55w.gif (14.2 KB, 4885 views)
File Type: gif Pdist_T2_4ohm_100w.gif (15.7 KB, 4857 views)
File Type: gif DistF_L20D_8ohm_17Vrms.gif (15.9 KB, 4839 views)
File Type: gif DistF_L20D_4ohm_17Vrms.gif (15.8 KB, 748 views)
File Type: gif Pdist_L20D_8ohm_200W.gif (16.4 KB, 739 views)
File Type: gif Pdist_L20D_4ohm_200W.gif (16.8 KB, 700 views)
File Type: gif DistF_SURE_8ohm_4r4Vrms.gif (14.6 KB, 650 views)
File Type: gif Pdist_SURE_8ohm_55W.gif (14.0 KB, 614 views)

Last edited by trevmar; 14th August 2011 at 07:28 PM. Reason: typo
  Reply With Quote
Old 14th August 2011, 09:59 PM   #2
diyAudio Member
 
Saturnus's Avatar
 
Join Date: Jun 2005
Location: Copenhagen, Denmark
What you see is very typical. Tripath based amps typically have higher average THD than many other comparable amps (though much lower than many other designs) but because of it's sigma-delta comparator technique it's completely flat unlike what you see from the I-R based which shows a rising tendency with higher frequencies.

But it's also a quite unfair comparison. The IRS2092 should be compared to the TA3020, not the TC2000. The TDA7498 isn't even in the same league so I'm not sure why that's being tested against the 2 others.

Last edited by Saturnus; 14th August 2011 at 10:05 PM.
  Reply With Quote
Old 14th August 2011, 11:14 PM   #3
trevmar is offline trevmar  United States
diyAudio Member
 
Join Date: Jan 2011
A rising tendency? That's not really what I see.
The Tripath is indeed flat with frequency, but at a relatively high level of -45dB, or about 0.3%, and while the I-R based L20D is indeed rising, the I-R is just much, much lower distortion. never going above -70dB (0.03%) (both systems measured into 8 ohms at 17Vrms). It is important to look at the magnitudes, not just the shape The I-R leaves the Tripath behind in every distortion comparison, it's just that the Tripath is arguably adequate in its performance, remaining below half a percent at all (audible) frequencies, especially when you don't drive it near its power ratings.

With newer loudspeakers, some would argue whether 0.3% is indeed enough. I have measured my Peerless 830983 at about -60dB THD throughout the midrange, for example, and they may be capable of outperforming a 0.3% amplifier in overall distortion if you don't drive them too hard. Who knows? For quality, I would choose the I-R if I could. But the Tripath is more convenient for smaller systems, working with a single-rail power supply (or power brick)...
.

Last edited by trevmar; 14th August 2011 at 11:33 PM. Reason: typo
  Reply With Quote
Old 14th August 2011, 11:43 PM   #4
diyAudio Member
 
Saturnus's Avatar
 
Join Date: Jun 2005
Location: Copenhagen, Denmark
Well, the HifimeDIY T2 isn't a terribly good design to start with.

Probably should read this.

41Hz Audio - AMP15 performance measurements
  Reply With Quote
Old 15th August 2011, 12:02 AM   #5
trevmar is offline trevmar  United States
diyAudio Member
 
Join Date: Jan 2011
Hmm.. Lots of data in that 41Hz report, probably too much for anybody to absorb at one sitting, Showing spectra is a little misleading, as THD is indeed TOTAL harmonic distortion, when one looks at spectral lines one usually fails to sum up the individual contributions. Noise floors are of little importance these days, noise in any decent power amp is inaudible, especially when compared with system noise -- and the noise in the listening environment. The 41Hz report would seem less overwhelming if they would stick to the normal performance measures and presentation.

But the 41Hz distortion data is interesting, as it begs the question, how could 41Hz get that data from the same chip as I just tested in the HifimeDIY? There just are no passive components in either circuit which could account for distortion differences of that magnitude. It must come down to 'switching dead time' and other difficult design issues. I am always intrigued when I see good data for which there is no viable explanation -- there has to be an explanation somewhere, and it rarely hides in the brand of bypass capacitors one or the other system is using. Perhaps 41Hz might explain to me what they are doing which HifimeDIY are not? The T2 looks a good clean board, well thought out, with quality components in all the correct places.

I am not really tempted to spend the money on a 41Hz board just to test it directly against the HifimeDIY using the same test procedures, but I suspect that is what would be required to perform a true comparison...

Oh - with respect to the TDA7498, the data sheet shows distortion in the -60dB region (see below), why do you say it's not even in the same league?
.
Attached Images
File Type: gif TDA7498.gif (38.4 KB, 696 views)

Last edited by trevmar; 15th August 2011 at 12:15 AM. Reason: thinko and typo
  Reply With Quote
Old 15th August 2011, 07:56 AM   #6
diyAudio Member
 
Saturnus's Avatar
 
Join Date: Jun 2005
Location: Copenhagen, Denmark
Quote:
Originally Posted by trevmar View Post
Oh - with respect to the TDA7498, the data sheet shows distortion in the -60dB region (see below), why do you say it's not even in the same league?
.
The data shown in that 41hz info is for the TA3020 driver chip, the one that is similar in design and application to IRS2092, not the TC2001 used in HifiDIY D2 (or amp11).

Have you heard the TDA7468? It doesn't compare to any of the chips mentioned above but is a low cost alternative.
  Reply With Quote
Old 15th August 2011, 01:42 PM   #7
trevmar is offline trevmar  United States
diyAudio Member
 
Join Date: Jan 2011
Saturnus,
The TA3020 chip is nothing whatsoever "similar in design and application to IRS2092." The I-R technology uses low-order Delta-Sigma (fuzzy frequency) technology, a PWM encoding method I helped develop in the 1970's (when I published several papers showing methods of implementing delta-sigma). The TA3020 chip, on the other hand, uses the Tripath clocked-sample encoding technology. You can see from the test measurements in my first post that the I-R Delta-Sigma technology produces higher fidelity, distortion numbers which are much better than any of the Tripath chips. The sound is superb, rivaling the linear class AB amplifiers which I used to design.

As for your question "have you heard the TDA7468," I actually have a TDA7498 board in my possession, I published the test data above, and yes, I have listened to it extensively. There are very few DIY boards using this chip, primarily just the new SURE range, and so I suspect there are very few other members here who have actually had a good look at (or listen to) this new chip. I think the TDA7498 has potential to fill a gap at the low-end, for a lightweight, tiny, board.

IMO the IRS2092 I-R technology is disruptive technology. It takes the performance of switching amplifiers to a new level, both in reproduction fidelity and increased power level. I can understand how people who have a vested interest in the previous technologies would like to deny the existence of change, but IMO it is inevitable, as, unlike Tripath, International Rectifier is still a flourishing company, continuing to develop its products.

I will take another look at the SURE TDA7498 board later today, and report my finding here.

Meanwhile, I did measure the distortion curves for one of the low-cost YuanJing TDA8920B boards that I bought so cheaply on Ebay, and you can find the data in the attachments below. The performance is not bad, which is probably why it didn't sound so bad, either Distortion vs frequency is shown at a 5 watt power level, followed by distortion vs output power at 1KHz into 8 ohms, on a 25-0-25 volt DC power supply.
.
Attached Images
File Type: jpg Yuanjing_closeup.jpg (109.3 KB, 1143 views)
File Type: gif DistF_TDA8920_5V9rms_8ohm.gif (15.5 KB, 1033 views)
File Type: gif Pdist_TDA8920B_25-25V_8ohm.gif (14.9 KB, 508 views)

Last edited by trevmar; 15th August 2011 at 02:02 PM. Reason: typo and clarification
  Reply With Quote
Old 15th August 2011, 03:24 PM   #8
diyAudio Member
 
Saturnus's Avatar
 
Join Date: Jun 2005
Location: Copenhagen, Denmark
I have no vested interest in any of the above. My requirements for amp chips are fairly simple.

- Must use single rail supply only.
- Max supply voltage preferably optimzed for under 40V.
- Must be monolothic in design, ie. must not be a external FET driver.
- Ok, if it's a DDX output chip driver.
- Must have sound quality equal to or better than available Tripath chips

What I'm trying to explain to you is that the chips you are comparing are completely different in purpose and use.

The IRS2092 is +-100V dual rail voltage FET driver. From Tripath that would compare to TA3020 as that is a +-70V dual rail voltage FET driver.

The TDA7468 is a dual rail voltage monolithic design. From Tripath that would compare to TA2022 which is also a dual rail voltage monolithic design.

The TC2001 is a DDX driver (and therefore naturally single rail voltage). Distortion would primarily depend on the DDX output chip. In T2 that can be both TP2050 or STA505. You don't specify which version. The T4 with STA517B would be far better though. I has much lower THD than both the types used in the 2 versions of the T2.

Last edited by Saturnus; 15th August 2011 at 03:49 PM.
  Reply With Quote
Old 16th August 2011, 03:43 AM   #9
trevmar is offline trevmar  United States
diyAudio Member
 
Join Date: Jan 2011
I have retested the amplifier I received from SURE Electronics which was labelled as: "2 X 25Watt Class D Audio Amplifier Board - TDA7492" and which came with a chip whose top was laser-embossed as 'TDA7498'.

This amplifier seems to be using a chip which does not conform to the distortion specifications in the data sheet for either TDA7492 or the newer TDA7498. My best guess is that is a "seconds" chip, which, eg, 'fell off the back of a truck'. I have tested the TDA7920B chips from ST microelectronics, which largely perform to their data sheet. But the SURE amplifier has harmonic distortion which is unacceptable, and way above the ST data sheet values of either chip. I cannot believe that SURE could mess up their implementation so completely, although that was my first reaction, and have come to conclude it must be a second-rate chip.

Today I removed the tiny 33uH output inductors used on the SURE board and replaced them with the larger 22uH inductors which work well on the TDA7920B board. The distortion was still high, although a little better, certainly not as good as the same inductors produced on the TDA8920B Yuanjing board.

Below please find attachments in support of my conclusion. First I have a photo of my board modified with the two larger output inductors on the left channel of the board, and with the original small 330 inductors on the right. Second is distortion vs power into 8 ohms with a 24V supply and the original 330 inductors, third is with the larger 220 inductors. Then the distortion vs frequency into 8 ohms with a 24V supply at an output power of 6 watts is shown with the unmodified board. Finally, to show that the larger inductors can handle the power levels without distortion, I attach the distortion vs power curve of the TDA8920B YuanJing board which I 'borrowed' them from.
.
Attached Images
File Type: jpg SURE_TDA7498_ww_Inductors.jpg (187.5 KB, 844 views)
File Type: gif Pdist_SURE_24VDC_8ohm_crop.gif (15.2 KB, 687 views)
File Type: gif Pdist_SURE_24VDC_8ohm_22-22inductor_crop.gif (15.1 KB, 296 views)
File Type: gif DistF_SURE_24VDC_5Vrms_8ohm.gif (15.9 KB, 255 views)
File Type: gif Pdist_TDA8920B_25-25V_8ohm.gif (14.9 KB, 260 views)

Last edited by trevmar; 16th August 2011 at 03:47 AM.
  Reply With Quote
Old 16th August 2011, 04:54 AM   #10
diyAudio Member
 
Join Date: Dec 2004
Location: Reston, Virginia
Thanks for doing this work. I've made a couple of TDA8920 boards and always wondered how well they performed in a commercial design. This is good information. And it's also good to see a quantitative comparison of the output inductors.

Looks like the IR technology really is a huge step forward from the older designs. And when people are selling high quality 250W amps for $37/pr, that really qualifies as "disruptive technology".

I wish Analog Devices would come out with a scaled up version of their AD1994 (RIP) chip, as it would probably provide some good competition to the IR design. It would be nice to see some tests of the Zetex circuits as well.
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
hifimediy T2 mods? bdbender Class D 20 12th August 2011 01:08 AM
WTB: Hifimediy T2 Frosteh Swap Meet 1 7th August 2011 09:03 PM
Improving Hifimediy t2 jtjy Class D 3 20th July 2011 06:02 PM
Power supply for Hifimediy T2 eladmi Power Supplies 0 10th March 2011 08:14 PM
Hifimediy T3 and T2 amps... oppinions? jaistanley Class D 6 30th November 2010 11:36 PM


New To Site? Need Help?

All times are GMT. The time now is 03:26 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2