ucd 25 watts to 1200 watts using 2 mosfets - Page 23 - diyAudio
Go Back   Home > Forums > Amplifiers > Class D

Class D Switching Power Amplifiers and Power D/A conversion

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 27th July 2010, 04:56 PM   #221
lycanlk is offline lycanlk  Sri Lanka
diyAudio Member
 
Join Date: Sep 2009
Default here is the copper paths

But I recommend you to follow the original by the author..

Anyway my design works well except the noise at high frequency. I open this to build and test by yourself.

regards,
Lycanlk
Attached Files
File Type: pdf EJTAGLE UCD.pdf (62.6 KB, 1254 views)
  Reply With Quote
Old 27th July 2010, 05:39 PM   #222
lycanlk is offline lycanlk  Sri Lanka
diyAudio Member
 
Join Date: Sep 2009
Default A very small change.. this can be ignored..

found a better place for 100p at FET

regards,
Lycanlk
Attached Files
File Type: pdf EJTAGLE-UCD.pdf (148.8 KB, 1170 views)
File Type: pdf EJTAGLE-UCD-COMP.pdf (183.2 KB, 1222 views)
  Reply With Quote
Old 27th July 2010, 08:09 PM   #223
stewin is offline stewin  Kenya
diyAudio Member
 
Join Date: Jul 2007
high guys i've sought of reduced the noise in my amp by adding 1nf between pin 2 and 3 of lm 311 and i want to try using the below scheme for the input of lm311pls advice also i've managed to bridge the amp ( very power full) i used just the ir2110 pins lin & hin but i've not included the feed back on the other channel but works fine, voltage 56v -0- 56v irf540 warms a little. any ideas i would appreciate . steve
Attached Files
File Type: pdf 1200W.pdf (78.7 KB, 1427 views)
  Reply With Quote
Old 27th July 2010, 10:02 PM   #224
stewin is offline stewin  Kenya
diyAudio Member
 
Join Date: Jul 2007
just removed the 1nf between pin 2 & 3 of lm311 and placed 4.7nf capacitor at pin 3 of lm311 and connected to the ground ovlts and added a 5.6k resistor before the input . and the noise is small hard to notice stewin
  Reply With Quote
Old 27th July 2010, 11:41 PM   #225
diyAudio Member
 
andrewlebon's Avatar
 
Join Date: Feb 2008
hi lycanik
greetings thanks for the design
thanking you
andrew
  Reply With Quote
Old 28th July 2010, 01:04 AM   #226
diyAudio Member
 
Join Date: Sep 2009
Location: Romania,Calarasi
Send a message via Yahoo to ionutzxpo
hello Lycanlk can you tell us the size off the PCB? thanks
  Reply With Quote
Old 28th July 2010, 01:25 AM   #227
diyAudio Member
 
andrewlebon's Avatar
 
Join Date: Feb 2008
hi stewin
greetings after bridging how does is it sound how many watts do you
think its why are you not using irfp250 the schematic you posted is it diy or
from some proffessional amp seems to complicated
thanking you
andrew lebon
Attached Files
File Type: pdf 1200W_2.pdf (78.1 KB, 1066 views)
  Reply With Quote
Old 28th July 2010, 05:33 AM   #228
lycanlk is offline lycanlk  Sri Lanka
diyAudio Member
 
Join Date: Sep 2009
Default 88.2mm x 73.9mm

Quote:
Originally Posted by ionutzxpo View Post
hello Lycanlk can you tell us the size off the PCB? thanks
Attached Files
File Type: pdf EJTAGLE-UCD sizes.pdf (93.9 KB, 1032 views)
  Reply With Quote
Old 28th July 2010, 07:39 AM   #229
stewin is offline stewin  Kenya
diyAudio Member
 
Join Date: Jul 2007
Quote:
Originally Posted by andrewlebon View Post
hi stewin
greetings after bridging how does is it sound how many watts do you
think its why are you not using irfp250 the schematic you posted is it diy or
from some proffessional amp seems to complicated
thanking you
andrew lebon
hi andrew lebon the scheme was posted by nikula and on pg 6 of the below forum he has a completed and mounted it .

Building a 1000W @ 8ohms class D amplifier from zero
  Reply With Quote
Old 29th July 2010, 03:50 PM   #230
opor is offline opor  Thailand
diyAudio Member
 
Join Date: Nov 2005
Hi all,

Need for your recommend . I would like to add more output device for 2 ohm load. So is this schematic work?
Attached Files
File Type: pdf UcDbasedV2.pdf (27.4 KB, 1141 views)
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Philips 40/25/15 watts amplifier with Universal preamplifier circuit. renjiish Solid State 64 28th July 2014 11:33 AM
Decibel Watts VS Watts ? fivestring Solid State 11 1st April 2009 01:08 PM
AMP1-B: why only 25 watts @8ohms? theAnonymous1 Class D 10 15th August 2005 06:55 PM
Sound quality of amps at 0.3 watts vs @ typical 5 watts rick57 Solid State 2 26th March 2005 06:25 AM
Need 2 watts Vivek Everything Else 4 17th July 2003 08:29 AM


New To Site? Need Help?

All times are GMT. The time now is 04:32 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright ©1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2