Hypex UcD AS2.100

[korben69]

Originally posted by Jan-Peter


Sorry, I mixed up the AS2.100 with the upcomming high end DSP solution.

The upcomming high end DSP solution;
- fully balanced input two channels and 6 channels balanced output.
- no power amplifiers, only high end D/A converters from AKM.
- it's only a DSP board, size aprox. 100x100mm


Jan-Peter

So BTW we could re-use existing UcD modules
Another stupid question : the output volume control will be available for the 6 chanels ?

[Jan-Peter]

Originally posted by korben69


So BTW we could re-use existing UcD modules ?

Correct!

Not possible with the AS2.100, this one use already this module;
http://www.hypex.nl/docs/UcD100OEM_datasheet.pdf

Ok, if you have a lot of electronic experience you can remove the UcD100OEM modules add some wiring and connect this to another UcD module. But we will not recommend this....


Jan-Peter

[korben69]

Originally posted by korben69

Another stupid question : the output volume control will be available for the 6 channels ?

You've missed this point while I was editing...
I mean separately adjustable by pair.

[fb]

Originally posted by Jan-Peter
indeed a second TAS3108 can eb add to increase delay time, or FIR filtering what you wants.

Originally posted by Jan-Peter


The upcomming high end DSP solution;
- fully balanced input two channels and 6 channels balanced output.
- no power amplifiers, only high end D/A converters from AKM.
- it's only a DSP board, size aprox. 100x100mm

Great!


Any chance of per-channel limiters too?

[Jan-Peter]

Originally posted by korben69


You've missed this point while I was editing...
I mean separately adjustable by pair.

We can take this in consideration...

Originally posted by fb


Great!

Any chance of per-channel limiters too?

We will stay working on the software, so in future we will have good sounding limiters, also for every channel.


Jan-Peter

[fram]

Dear Jan-Peter,

What about keypad? Is it in the package for each AS2.100? Or we need to buy it separatly?

Because if i'm right in the case we use 2 modules, the best way is:
-a master module (with digital input will be better) and a keypad
-a slave analog module without keypad

In this case, only one keypad is needed.

A last question: is it possible to have an auto on/off , auto on only when signal is incoming in the module, and auto off when no signal input (with a delay maybe?)

regards,
Franck

[Jan-Peter]

Originally posted by fram
Dear Jan-Peter,

What about keypad? Is it in the package for each AS2.100? Or we need to buy it separatly?

Because if i'm right in the case we use 2 modules, the best way is:
-a master module (with digital input will be better) and a keypad
-a slave analog module without keypad

In this case, only one keypad is needed.

A last question: is it possible to have an auto on/off , auto on only when signal is incoming in the module, and auto off when no signal input (with a delay maybe?)

regards,
Franck

Good point!

Every AS2.100 will have a simple PCB with three control keys, and IR receiver.

With the AS2.100 you only need one keypad, the other is not needed anymore.

In future we will come with a very nice touchpanel, this will be an extra option.

There is no auto on/off mode. In practice customers are always complaining if the amps swich off to fast at very low volumes.

With the (optional) remote control unit you can switch the amp in standby mode.

Jan-Peter

[tinitus]

Hi Jan-Peter

When will plate subamps come with this technology

[Jan-Peter]

Originally posted by tinitus
Hi Jan-Peter

When will plate subamps come with this technology

You can use the AS2.100 to build a sub amp, bridge the two amps and you will have a 150W subamp.

Or wait until we release the PSC2.400; www.hypex.nl/docs/PSC2.400.pdf

This will give you a very power full subwoofer amplifier....

Jan-Peter

[boudy]

Is 120V operation an option?