Diamond Audio D6 1500.1

allaroundsound · 6th February 2012, 11:34 PM

amp has burn marks on board at component u30d20a "mospec". The amp, when only b+ and main ground are applied turns on and shows voltage on the remote. . No remote power applied. Amp powers up and power led is green, no protect light. This part is perhaps the neg. rectifier? Here's the readings on that part powered up;

pin #1 .034 volts
pin #2 -105.7 volts
pin #3 .035 volts

[IMG]

[/IMG]

[IMG]

[/IMG]

timwebb · 7th February 2012, 12:11 AM

what is the amp doing? is it producing any sound?

allaroundsound · 7th February 2012, 12:26 AM

i might have factory wave soldering issue. there are many areas that need solder still. ill get u an update when i get it back together. and yes it has audio timwebb. very low power.

allaroundsound · 7th February 2012, 02:48 AM

is it ok to sub a small 10mf 50volt for a small 10mf 100volt in a class d amp?

timwebb · 7th February 2012, 02:51 AM

i dont know. depending where it goes.

allaroundsound · 7th February 2012, 02:56 AM

top right section of above picture #2. all four caps were folded over and all had one leg each broken off the board. strange. they are all about a half inch tall and a quarter inch diameter. thanks

allaroundsound · 7th February 2012, 02:57 AM

i have didrect replacement for 2 out of four. the remaining two i only have 100volt ratings not 50volt. all the new ones will fit well.

timwebb · 7th February 2012, 03:01 AM

those should be the voltage regulators. depending how much voltage is on them u might get away with it. but it would be best to use the 100v caps.

allaroundsound · 7th February 2012, 03:03 AM

ok. the originals are 50 volt. im going to install 100volt caps. thank you

timwebb · 7th February 2012, 03:21 AM

oh i read it wrong my bad. it will work.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Diamond Audio D6 1500.1 diagram	clayton	Car Audio	10	14th May 2012 01:46 PM
Diamond D6 1000.1 R101 value	brandes.cm	Car Audio	9	14th January 2012 05:00 AM
Wierd turn-on noise with my Diamond Audio d6 700.4	rc10mike	Car Audio	5	23rd January 2010 03:35 PM
Infinity Kappa Perfect vs. Diamond D6	chcc5th	Car Audio	1	7th May 2007 05:14 PM
Diamond Audio D6 1500.1 manual?	mbayaq579	Car Audio	2	8th March 2007 07:30 AM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

6th February 2012, 11:34 PM	#1
allaroundsound diyAudio Member Join Date: Oct 2011 Location: californi	Diamond Audio D6 1500.1 amp has burn marks on board at component u30d20a "mospec". The amp, when only b+ and main ground are applied turns on and shows voltage on the remote. . No remote power applied. Amp powers up and power led is green, no protect light. This part is perhaps the neg. rectifier? Here's the readings on that part powered up; pin #1 .034 volts pin #2 -105.7 volts pin #3 .035 volts [IMG][/IMG] [IMG][/IMG]

7th February 2012, 12:11 AM	#2
timwebb diyAudio Member Join Date: Jan 2010 Location: memphis tn	what is the amp doing? is it producing any sound?

7th February 2012, 12:26 AM	#3
allaroundsound diyAudio Member Join Date: Oct 2011 Location: californi	i might have factory wave soldering issue. there are many areas that need solder still. ill get u an update when i get it back together. and yes it has audio timwebb. very low power.

7th February 2012, 02:48 AM	#4
allaroundsound diyAudio Member Join Date: Oct 2011 Location: californi	is it ok to sub a small 10mf 50volt for a small 10mf 100volt in a class d amp?

7th February 2012, 02:51 AM	#5
timwebb diyAudio Member Join Date: Jan 2010 Location: memphis tn	i dont know. depending where it goes.

7th February 2012, 02:56 AM	#6
allaroundsound diyAudio Member Join Date: Oct 2011 Location: californi	top right section of above picture #2. all four caps were folded over and all had one leg each broken off the board. strange. they are all about a half inch tall and a quarter inch diameter. thanks

7th February 2012, 02:57 AM	#7
allaroundsound diyAudio Member Join Date: Oct 2011 Location: californi	i have didrect replacement for 2 out of four. the remaining two i only have 100volt ratings not 50volt. all the new ones will fit well.

7th February 2012, 03:01 AM	#8
timwebb diyAudio Member Join Date: Jan 2010 Location: memphis tn	those should be the voltage regulators. depending how much voltage is on them u might get away with it. but it would be best to use the 100v caps.

7th February 2012, 03:03 AM	#9
allaroundsound diyAudio Member Join Date: Oct 2011 Location: californi	ok. the originals are 50 volt. im going to install 100volt caps. thank you

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)

7th February 2012, 03:21 AM	#10
timwebb diyAudio Member Join Date: Jan 2010 Location: memphis tn	oh i read it wrong my bad. it will work.