MOX - active crossover

moamps · 5th February 2004, 09:44 PM

Hi, all

here is my prototipe of an active crossover - SK filter with 6-12-18-24 dB slope, Q from 0.5 to 1, and standard 1/3 octave central frequency. I'm using this crossover now in an active PA speaker project of mine. Schematics and pcb's have been tested and are working fine. PCB's are one layer style with a couple of jumpers, opamp is placed on a small "daughter" board and can be IC or discrete. If you find it useful, feel free...

Regards

moamps · 5th February 2004, 09:45 PM

LPF filter schematic

moamps · 5th February 2004, 09:47 PM

HPF filter schematic

moamps · 5th February 2004, 09:48 PM

discrete opamp

moamps · 5th February 2004, 09:50 PM

complete xover

moamps · 5th February 2004, 09:53 PM

measurements...24dB/oct LPF, middle decade

moamps · 5th February 2004, 09:55 PM

measurements...1kHz lpf 24dB/octave, diferent Q

moamps · 5th February 2004, 09:59 PM

parts list

Peter Daniel · 5th February 2004, 10:12 PM

I'd say, you'd finished what Grey started. Congratulations on a job well done. Will definitely try this one.

Peter Daniel · 6th February 2004, 03:26 AM

Looking at the schematic, I see you have 10K volume pots for ea. section of the crossover.

It seems like a perfect setup to use APOX SHM controller here, as one could set permanently offset levels and then adjust all 4 channels simultaniously. By increasing the gain of op amp, one might combine preamp function with high quality active crossover.

From the schematics I've seen so far, this one seems to be the most appealing (especially when it's based on XVR1

)

6th February 2004, 03:26 AM	#10
Peter Daniel diyAudio Member Join Date: Jul 2002 Location: Toronto, Canada	Looking at the schematic, I see you have 10K volume pots for ea. section of the crossover. It seems like a perfect setup to use APOX SHM controller here, as one could set permanently offset levels and then adjust all 4 channels simultaniously. By increasing the gain of op amp, one might combine preamp function with high quality active crossover. From the schematics I've seen so far, this one seems to be the most appealing (especially when it's based on XVR1)

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
active crossover: fir vs iir	netchris	Everything Else	3	29th July 2008 09:14 AM
Passive crossover into active crossover	hahfran	Multi-Way	16	10th February 2008 06:16 PM
PA vs DIY active crossover	paulspencer	Multi-Way	46	27th November 2004 01:25 AM
active crossover	aaronboumans	Analogue Source	4	31st May 2003 04:59 PM
XVR1 active crossover, discrete active stage	promitheus	Pass Labs	18	22nd July 2002 01:29 AM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

5th February 2004, 10:12 PM	#9
Peter Daniel diyAudio Member Join Date: Jul 2002 Location: Toronto, Canada	I'd say, you'd finished what Grey started. Congratulations on a job well done. Will definitely try this one.