I tend to give people the benefit of doubt, but you guys tell me if I was duped into buying a Toroid I thought was a 2kVA Part.
It is pictured here in the middle next to 3 different 1 kVA toroids that I already own and know they are 1 kVA. The one on the left is a Plitron, the top one is Antek and the large one on the bottom is a Hammond.
While I know "size aint everything".... I cannot get over the thought that this no name part cannot be 2kVA .
(PS: I will not disclose the DIY member who sold it to me for he may come clean on his own...)
Best,
K-Dupee
It is pictured here in the middle next to 3 different 1 kVA toroids that I already own and know they are 1 kVA. The one on the left is a Plitron, the top one is Antek and the large one on the bottom is a Hammond.
While I know "size aint everything".... I cannot get over the thought that this no name part cannot be 2kVA .
(PS: I will not disclose the DIY member who sold it to me for he may come clean on his own...)
Best,
K-Dupee
Attachments
To be fair, the supposed 2kVA part is slightly taller than the Plitron and the Hammond Toroid but about the same as the Antek...
As far as mass goes...
Antek 1kVA : 15.0 lbs
Plitron 1kVA : 15.5 lbs
Hammond 1kva : 23.0 lbs
2kva "supposed" 14.5 lbs....
As far as mass goes...
Antek 1kVA : 15.0 lbs
Plitron 1kVA : 15.5 lbs
Hammond 1kva : 23.0 lbs
2kva "supposed" 14.5 lbs....
Attachments
K,
could be in good faith, half of the population here can't recognise their own dickcheney if it was electronic.
I've got a couple of 1kW Plitrons, and find them pretty sizy compared to most other brands.
Got some biggies in the 1.8 to 2kW range from other toroid manufacturers, some are not much bigger than the Plitrons overall but each one easily outweighs them.
If your 2kWatter weighs less than the 1kW Canadian, you've been conned imo.
could be in good faith, half of the population here can't recognise their own dickcheney if it was electronic.
I've got a couple of 1kW Plitrons, and find them pretty sizy compared to most other brands.
Got some biggies in the 1.8 to 2kW range from other toroid manufacturers, some are not much bigger than the Plitrons overall but each one easily outweighs them.
If your 2kWatter weighs less than the 1kW Canadian, you've been conned imo.
Yeah,
Hammond transformers makes you vision chunky Canadian dames in lumber shirts that offer the option of armwrestling you under the table or the stretched embarassment of the same by outdrinking you. (i hate to see Ozzy toroids, and i stopped JB shots contests with women)
Hammond transformers makes you vision chunky Canadian dames in lumber shirts that offer the option of armwrestling you under the table or the stretched embarassment of the same by outdrinking you. (i hate to see Ozzy toroids, and i stopped JB shots contests with women)
K-amps said:
As far as mass goes...
Antek 1kVA : 15.0 lbs
Plitron 1kVA : 15.5 lbs
Hammond 1kva : 23.0 lbs
2kva "supposed" 14.5 lbs....
Even if weight is not everything ( wires matters, too )
when it comes to toroid transformers:
Weight DOES NOT LIE
lineup
Hi,
Harbuch Antrim 2kVA toriods are 17kg. Unfortunately I don't know what lbs are anymore but they used to be a lot smaller than kg.
http://ourworld.compuserve.com/homepages/harbuch/harbuch.htm
regards
Harbuch Antrim 2kVA toriods are 17kg. Unfortunately I don't know what lbs are anymore but they used to be a lot smaller than kg.
http://ourworld.compuserve.com/homepages/harbuch/harbuch.htm
regards
Greg Erskine said:
Harbuch Antrim 2kVA toriods are 17kg. Unfortunately I don't know what lbs are anymore but they used to be a lot smaller than kg.
http://ourworld.compuserve.com/homepages/harbuch/harbuch.htm
What I recall (not sure):
1 lbs = 0.45 kg
1 kg = 2.2 lbs
17 kg should then be ~37 lbs
( compare to those 1 kVA ~15 lbs )
------------------------------
edit:
found a link about metrics, and
With online conversion service
http://www.curezone.com/conversions.asp
16 oz. = (1 lbs.) 453.5 g = 0.453 Kg
1 oz. = 30 g 1 lbs. = 16 oz. (453.5 g)
1 g = 0.35 oz. 1 kg = 2.2 lbs. = 1000 g
Toroid Tranformer Weight VA rating formula
.
I looked up several Toroid Transformer manufacturers data.
Based on VA ratings / weight data we make up some rough formulas.
I think most makers of transformers use a core material
with almost the same quality.
There are always exceptions, but for the major public main stream market, to affordable prices,
I would say there are only small differences.
Say max +-15 % in VA per core weight.
######################################
Here is my attempt to make such rule of the thumb formulas.
The Toroid Transformer data I used comes in 15 - 4000 VA
and looks like this:
Approximate formulas.
Example:
A toroid weighs 1.9 kg. Set k=0.4
VA = 100(1.9-0.4) = 100x1.5
= 150 VA
..................................................................................
Web Reference used:
Shenzhen Okerda Science & Technology Co., Ltd
is a manufacturer specializing in custom designed transformers, coils, and power supplies.
OKERDA HEAD OFFICE (SHENZHEN)
Shenzhen City, Guangdong Province 518110, P.R.China
British Office:
Mr. Hao
Tel: 0044—2089856157, Cell phone: 07830113768
Address: 80B, Coopersale Road, Homerton, Hackney, London, UK E9 6BA
http://www.okerda-tech.com/
.....................................................................................
lineup
Lineup Audio Lab
Audio Mains Transformers Division
.
I looked up several Toroid Transformer manufacturers data.
Based on VA ratings / weight data we make up some rough formulas.
I think most makers of transformers use a core material
with almost the same quality.
There are always exceptions, but for the major public main stream market, to affordable prices,
I would say there are only small differences.
Say max +-15 % in VA per core weight.
######################################
Here is my attempt to make such rule of the thumb formulas.
The Toroid Transformer data I used comes in 15 - 4000 VA
and looks like this:
Approximate formulas.
0.6 - 4.5 kg (30 -> 400 VA)
VA = 100 (kg - k) where k= 0.3 -> 0.5
5 - 8.5 kg (500 - 800 VA)
VA = 100 x kg
> 9 kg (1000 - 4000 VA)
1000VA 09.5 kg, 20.9 lbs
2000VA 15.6 kg, 34.3 lbs
3000VA 22.3 kg, 49.0 lbs
4000VA 31.5 kg, 69.3 lbs
Example:
A toroid weighs 1.9 kg. Set k=0.4
VA = 100(1.9-0.4) = 100x1.5
= 150 VA
..................................................................................
Web Reference used:
Shenzhen Okerda Science & Technology Co., Ltd
is a manufacturer specializing in custom designed transformers, coils, and power supplies.
OKERDA HEAD OFFICE (SHENZHEN)
Shenzhen City, Guangdong Province 518110, P.R.China
British Office:
Mr. Hao
Tel: 0044—2089856157, Cell phone: 07830113768
Address: 80B, Coopersale Road, Homerton, Hackney, London, UK E9 6BA
http://www.okerda-tech.com/
.....................................................................................
lineup
Lineup Audio Lab
Audio Mains Transformers Division
Attachments
The Saint said:This is a 4KVA transformer I am using for my prototype 2kw GND Bridge amplifier.
There is no way that transformer is 2kva
Now THAT's a knife.
**Said in the Dundee Accent.
Re: Toroid Tranformer Weight VA rating formula
Thanks line-up... now gimmie a source for some cheap Prozac...
lineup said:.
I looked up several Toroid Transformer manufacturers data.
Based on VA ratings / weight data we make up some rough formulas.
I think most makers of transformers use a core material
with almost the same quality.
There are always exceptions, but for the major public main stream market, to affordable prices,
I would say there are only small differences.
Say max +-15 % in VA per core weight.
######################################
Here is my attempt to make such rule of the thumb formulas.
The Toroid Transformer data I used comes in 15 - 4000 VA
and looks like this:
Approximate formulas.
Example:
A toroid weighs 1.9 kg. Set k=0.4
VA = 100(1.9-0.4) = 100x1.5
= 150 VA
..................................................................................
Web Reference used:
Shenzhen Okerda Science & Technology Co., Ltd
is a manufacturer specializing in custom designed transformers, coils, and power supplies.
OKERDA HEAD OFFICE (SHENZHEN)
Shenzhen City, Guangdong Province 518110, P.R.China
British Office:
Mr. Hao
Tel: 0044—2089856157, Cell phone: 07830113768
Address: 80B, Coopersale Road, Homerton, Hackney, London, UK E9 6BA
http://www.okerda-tech.com/
.....................................................................................
lineup
Lineup Audio Lab
Audio Mains Transformers Division
Thanks line-up... now gimmie a source for some cheap Prozac...
The Saint said:This is a 4KVA transformer I am using for my prototype 2kw GND Bridge amplifier.
Those Toroids look great, Tony.
I know you have much experience, when comes to good High Power supplying.
Is there any TOROID brand you prefer?
What brand are those in your picture?
Regards
lineup
djQUAN said:it can be a 2KVA if it is an autotransformer.
I once bought a 220 to 110V converter rated at 1kVA. I wanted to get the toroid and add a secondary to end up with an isolated transformer.
the toroid inside was the size of a 500VA transformer.
What I am looking for is regulation capabilities from the tranny not steady 2kW drain. So if it can keep up the rails... I may live with it (grudgingly).
The Saint said:Hey Lineup
I always use Harbuch Electronics Transformers
There is a link from my site
I believe they use Antrim Cores which they import from Ireland
they are excellent quality
Thanks, The Saint
I found link to Harbuch in this www.aussieamplifiers.com page:
Heat Sinks and Power Transformers
HARBUCH ELECTRONICS PTY LTD
HORNSBY
NSW 2077 AUSTRALIA
Harbuch Electronics - ANTRIM TOROID STANDARD SIZES / DATA
-----------------------------------
Harbuch toroids:
1000 VA, weight = 07.9 kg, ( 17.4 lbs )
2000 VA, weight = 17.0 kg, ( 37.4 lbs )
lineup
------------------------------------------------------
An externally hosted image should be here but it was not working when we last tested it.
* Antrim homepage:
http://www.antrimtransformers.com/
Antrim Transformers Limited
Northern Ireland
- Status
- This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button.
- Home
- Amplifiers
- Pass Labs
- Whats wrong with the picture?