i have this amp in and its dead. i cant get it to do anything. anyone worked one these?
T timwebb Member Joined 2010 2012-02-21 5:36 am #1 2012-02-21 5:36 am #1 i have this amp in and its dead. i cant get it to do anything. anyone worked one these? ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-21 7:33 am #2 2012-02-21 7:33 am #2 If no one can help, post a photo of the board. ••• More options Share T timwebb Member Joined 2010 2012-02-21 6:51 pm #3 2012-02-21 6:51 pm #3 ... Attachments IMG_20120221_122333.jpg 595.8 KB · Views: 104 IMG_20120221_122416.jpg 698.5 KB · Views: 109 IMG_20120221_122426(1).jpg 609.6 KB · Views: 93 ••• More options Share T timwebb Member Joined 2010 2012-02-22 11:57 am #4 2012-02-22 11:57 am #4 The amp is going into protection now but no voltages on both of the 494 ic. ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-22 6:22 pm #5 2012-02-22 6:22 pm #5 Follow the circuit back from pin 12 of the 494 to see what's supposed to be driving 12v to it. ••• More options Share T timwebb Member Joined 2010 2012-02-23 9:29 am #6 2012-02-23 9:29 am #6 ive traced it back to this diode but cant find the data sheet on it Attachments IMG_20120223_031227.jpg 376.7 KB · Views: 68 ••• More options Share T timwebb Member Joined 2010 2012-02-23 11:25 am #7 2012-02-23 11:25 am #7 Ok. I found it...trying to work on something half sleep. Anyway the diode is us1m-e3. It read 1.5 with diode check. Its connected to pin 12. ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-23 12:47 pm #8 2012-02-23 12:47 pm #8 I think that diode is likely across the relay coil (confirm). If so, you need to follow the trace back farther, possibly all of the way back to the remote turn-on terminal. ••• More options Share T timwebb Member Joined 2010 2012-02-23 1:23 pm #9 2012-02-23 1:23 pm #9 I think pin 8 and 12 are connected.the trace for pin 12 goes under the 494. Those the only two pins I read 0 ohms. I'm think the trace leads to the other driver card. ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-23 9:03 pm #10 2012-02-23 9:03 pm #10 You should read 0 ohms between 8 and 11. You'll have to follow it back farther. The trace may go to the other driver board but it may also go somewhere else. The other driver card isn't likely the source of power. ••• More options Share H Hexhclass Member Joined 2010 2012-02-24 1:36 am #11 2012-02-24 1:36 am #11 That 8 pin IC in the pic is that a hole in it? ••• More options Share T timwebb Member Joined 2010 2012-02-24 2:06 am #12 2012-02-24 2:06 am #12 which one? i got the amp to power up now ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:03 am #13 2012-02-24 7:03 am #13 The ic from your diode pic^^^^^^ sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 9:17 am #14 2012-02-24 9:17 am #14 its a clear hard substance on it maybe flux. ••• More options Share T timwebb Member Joined 2010 2012-02-24 12:47 pm #15 2012-02-24 12:47 pm #15 What's weird is this amp has two 494s controlling the amp. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 1:34 pm #16 2012-02-24 1:34 pm #16 It has 4 supplies, do they split two for the upper rail and two for the lower? sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:34 pm #17 2012-02-24 5:34 pm #17 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:51 pm #18 2012-02-24 5:51 pm #18 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:22 pm #19 2012-02-24 7:22 pm #19 Why is that odd? Are you sure someone else wasn't in there. sent from my RF T1000 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-24 8:14 pm #20 2012-02-24 8:14 pm #20 One is probably for the small transformer. The other for the rails supply. ••• More options Share 1 2 Next 1 of 2 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio US Amps VLX3DE Top Bottom
P Perry Babin Member Joined 2003 bcae1.com 2012-02-21 7:33 am #2 2012-02-21 7:33 am #2 If no one can help, post a photo of the board. ••• More options Share T timwebb Member Joined 2010 2012-02-21 6:51 pm #3 2012-02-21 6:51 pm #3 ... Attachments IMG_20120221_122333.jpg 595.8 KB · Views: 104 IMG_20120221_122416.jpg 698.5 KB · Views: 109 IMG_20120221_122426(1).jpg 609.6 KB · Views: 93 ••• More options Share T timwebb Member Joined 2010 2012-02-22 11:57 am #4 2012-02-22 11:57 am #4 The amp is going into protection now but no voltages on both of the 494 ic. ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-22 6:22 pm #5 2012-02-22 6:22 pm #5 Follow the circuit back from pin 12 of the 494 to see what's supposed to be driving 12v to it. ••• More options Share T timwebb Member Joined 2010 2012-02-23 9:29 am #6 2012-02-23 9:29 am #6 ive traced it back to this diode but cant find the data sheet on it Attachments IMG_20120223_031227.jpg 376.7 KB · Views: 68 ••• More options Share T timwebb Member Joined 2010 2012-02-23 11:25 am #7 2012-02-23 11:25 am #7 Ok. I found it...trying to work on something half sleep. Anyway the diode is us1m-e3. It read 1.5 with diode check. Its connected to pin 12. ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-23 12:47 pm #8 2012-02-23 12:47 pm #8 I think that diode is likely across the relay coil (confirm). If so, you need to follow the trace back farther, possibly all of the way back to the remote turn-on terminal. ••• More options Share T timwebb Member Joined 2010 2012-02-23 1:23 pm #9 2012-02-23 1:23 pm #9 I think pin 8 and 12 are connected.the trace for pin 12 goes under the 494. Those the only two pins I read 0 ohms. I'm think the trace leads to the other driver card. ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-23 9:03 pm #10 2012-02-23 9:03 pm #10 You should read 0 ohms between 8 and 11. You'll have to follow it back farther. The trace may go to the other driver board but it may also go somewhere else. The other driver card isn't likely the source of power. ••• More options Share H Hexhclass Member Joined 2010 2012-02-24 1:36 am #11 2012-02-24 1:36 am #11 That 8 pin IC in the pic is that a hole in it? ••• More options Share T timwebb Member Joined 2010 2012-02-24 2:06 am #12 2012-02-24 2:06 am #12 which one? i got the amp to power up now ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:03 am #13 2012-02-24 7:03 am #13 The ic from your diode pic^^^^^^ sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 9:17 am #14 2012-02-24 9:17 am #14 its a clear hard substance on it maybe flux. ••• More options Share T timwebb Member Joined 2010 2012-02-24 12:47 pm #15 2012-02-24 12:47 pm #15 What's weird is this amp has two 494s controlling the amp. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 1:34 pm #16 2012-02-24 1:34 pm #16 It has 4 supplies, do they split two for the upper rail and two for the lower? sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:34 pm #17 2012-02-24 5:34 pm #17 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:51 pm #18 2012-02-24 5:51 pm #18 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:22 pm #19 2012-02-24 7:22 pm #19 Why is that odd? Are you sure someone else wasn't in there. sent from my RF T1000 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-24 8:14 pm #20 2012-02-24 8:14 pm #20 One is probably for the small transformer. The other for the rails supply. ••• More options Share 1 2 Next 1 of 2 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio US Amps VLX3DE Top Bottom
T timwebb Member Joined 2010 2012-02-21 6:51 pm #3 2012-02-21 6:51 pm #3 ... Attachments IMG_20120221_122333.jpg 595.8 KB · Views: 104 IMG_20120221_122416.jpg 698.5 KB · Views: 109 IMG_20120221_122426(1).jpg 609.6 KB · Views: 93 ••• More options Share T timwebb Member Joined 2010 2012-02-22 11:57 am #4 2012-02-22 11:57 am #4 The amp is going into protection now but no voltages on both of the 494 ic. ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-22 6:22 pm #5 2012-02-22 6:22 pm #5 Follow the circuit back from pin 12 of the 494 to see what's supposed to be driving 12v to it. ••• More options Share T timwebb Member Joined 2010 2012-02-23 9:29 am #6 2012-02-23 9:29 am #6 ive traced it back to this diode but cant find the data sheet on it Attachments IMG_20120223_031227.jpg 376.7 KB · Views: 68 ••• More options Share T timwebb Member Joined 2010 2012-02-23 11:25 am #7 2012-02-23 11:25 am #7 Ok. I found it...trying to work on something half sleep. Anyway the diode is us1m-e3. It read 1.5 with diode check. Its connected to pin 12. ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-23 12:47 pm #8 2012-02-23 12:47 pm #8 I think that diode is likely across the relay coil (confirm). If so, you need to follow the trace back farther, possibly all of the way back to the remote turn-on terminal. ••• More options Share T timwebb Member Joined 2010 2012-02-23 1:23 pm #9 2012-02-23 1:23 pm #9 I think pin 8 and 12 are connected.the trace for pin 12 goes under the 494. Those the only two pins I read 0 ohms. I'm think the trace leads to the other driver card. ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-23 9:03 pm #10 2012-02-23 9:03 pm #10 You should read 0 ohms between 8 and 11. You'll have to follow it back farther. The trace may go to the other driver board but it may also go somewhere else. The other driver card isn't likely the source of power. ••• More options Share H Hexhclass Member Joined 2010 2012-02-24 1:36 am #11 2012-02-24 1:36 am #11 That 8 pin IC in the pic is that a hole in it? ••• More options Share T timwebb Member Joined 2010 2012-02-24 2:06 am #12 2012-02-24 2:06 am #12 which one? i got the amp to power up now ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:03 am #13 2012-02-24 7:03 am #13 The ic from your diode pic^^^^^^ sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 9:17 am #14 2012-02-24 9:17 am #14 its a clear hard substance on it maybe flux. ••• More options Share T timwebb Member Joined 2010 2012-02-24 12:47 pm #15 2012-02-24 12:47 pm #15 What's weird is this amp has two 494s controlling the amp. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 1:34 pm #16 2012-02-24 1:34 pm #16 It has 4 supplies, do they split two for the upper rail and two for the lower? sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:34 pm #17 2012-02-24 5:34 pm #17 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:51 pm #18 2012-02-24 5:51 pm #18 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:22 pm #19 2012-02-24 7:22 pm #19 Why is that odd? Are you sure someone else wasn't in there. sent from my RF T1000 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-24 8:14 pm #20 2012-02-24 8:14 pm #20 One is probably for the small transformer. The other for the rails supply. ••• More options Share 1 2 Next 1 of 2 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio US Amps VLX3DE Top Bottom
T timwebb Member Joined 2010 2012-02-22 11:57 am #4 2012-02-22 11:57 am #4 The amp is going into protection now but no voltages on both of the 494 ic. ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-22 6:22 pm #5 2012-02-22 6:22 pm #5 Follow the circuit back from pin 12 of the 494 to see what's supposed to be driving 12v to it. ••• More options Share T timwebb Member Joined 2010 2012-02-23 9:29 am #6 2012-02-23 9:29 am #6 ive traced it back to this diode but cant find the data sheet on it Attachments IMG_20120223_031227.jpg 376.7 KB · Views: 68 ••• More options Share T timwebb Member Joined 2010 2012-02-23 11:25 am #7 2012-02-23 11:25 am #7 Ok. I found it...trying to work on something half sleep. Anyway the diode is us1m-e3. It read 1.5 with diode check. Its connected to pin 12. ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-23 12:47 pm #8 2012-02-23 12:47 pm #8 I think that diode is likely across the relay coil (confirm). If so, you need to follow the trace back farther, possibly all of the way back to the remote turn-on terminal. ••• More options Share T timwebb Member Joined 2010 2012-02-23 1:23 pm #9 2012-02-23 1:23 pm #9 I think pin 8 and 12 are connected.the trace for pin 12 goes under the 494. Those the only two pins I read 0 ohms. I'm think the trace leads to the other driver card. ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-23 9:03 pm #10 2012-02-23 9:03 pm #10 You should read 0 ohms between 8 and 11. You'll have to follow it back farther. The trace may go to the other driver board but it may also go somewhere else. The other driver card isn't likely the source of power. ••• More options Share H Hexhclass Member Joined 2010 2012-02-24 1:36 am #11 2012-02-24 1:36 am #11 That 8 pin IC in the pic is that a hole in it? ••• More options Share T timwebb Member Joined 2010 2012-02-24 2:06 am #12 2012-02-24 2:06 am #12 which one? i got the amp to power up now ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:03 am #13 2012-02-24 7:03 am #13 The ic from your diode pic^^^^^^ sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 9:17 am #14 2012-02-24 9:17 am #14 its a clear hard substance on it maybe flux. ••• More options Share T timwebb Member Joined 2010 2012-02-24 12:47 pm #15 2012-02-24 12:47 pm #15 What's weird is this amp has two 494s controlling the amp. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 1:34 pm #16 2012-02-24 1:34 pm #16 It has 4 supplies, do they split two for the upper rail and two for the lower? sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:34 pm #17 2012-02-24 5:34 pm #17 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:51 pm #18 2012-02-24 5:51 pm #18 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:22 pm #19 2012-02-24 7:22 pm #19 Why is that odd? Are you sure someone else wasn't in there. sent from my RF T1000 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-24 8:14 pm #20 2012-02-24 8:14 pm #20 One is probably for the small transformer. The other for the rails supply. ••• More options Share 1 2 Next 1 of 2 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio US Amps VLX3DE Top Bottom
P Perry Babin Member Joined 2003 bcae1.com 2012-02-22 6:22 pm #5 2012-02-22 6:22 pm #5 Follow the circuit back from pin 12 of the 494 to see what's supposed to be driving 12v to it. ••• More options Share T timwebb Member Joined 2010 2012-02-23 9:29 am #6 2012-02-23 9:29 am #6 ive traced it back to this diode but cant find the data sheet on it Attachments IMG_20120223_031227.jpg 376.7 KB · Views: 68 ••• More options Share T timwebb Member Joined 2010 2012-02-23 11:25 am #7 2012-02-23 11:25 am #7 Ok. I found it...trying to work on something half sleep. Anyway the diode is us1m-e3. It read 1.5 with diode check. Its connected to pin 12. ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-23 12:47 pm #8 2012-02-23 12:47 pm #8 I think that diode is likely across the relay coil (confirm). If so, you need to follow the trace back farther, possibly all of the way back to the remote turn-on terminal. ••• More options Share T timwebb Member Joined 2010 2012-02-23 1:23 pm #9 2012-02-23 1:23 pm #9 I think pin 8 and 12 are connected.the trace for pin 12 goes under the 494. Those the only two pins I read 0 ohms. I'm think the trace leads to the other driver card. ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-23 9:03 pm #10 2012-02-23 9:03 pm #10 You should read 0 ohms between 8 and 11. You'll have to follow it back farther. The trace may go to the other driver board but it may also go somewhere else. The other driver card isn't likely the source of power. ••• More options Share H Hexhclass Member Joined 2010 2012-02-24 1:36 am #11 2012-02-24 1:36 am #11 That 8 pin IC in the pic is that a hole in it? ••• More options Share T timwebb Member Joined 2010 2012-02-24 2:06 am #12 2012-02-24 2:06 am #12 which one? i got the amp to power up now ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:03 am #13 2012-02-24 7:03 am #13 The ic from your diode pic^^^^^^ sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 9:17 am #14 2012-02-24 9:17 am #14 its a clear hard substance on it maybe flux. ••• More options Share T timwebb Member Joined 2010 2012-02-24 12:47 pm #15 2012-02-24 12:47 pm #15 What's weird is this amp has two 494s controlling the amp. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 1:34 pm #16 2012-02-24 1:34 pm #16 It has 4 supplies, do they split two for the upper rail and two for the lower? sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:34 pm #17 2012-02-24 5:34 pm #17 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:51 pm #18 2012-02-24 5:51 pm #18 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:22 pm #19 2012-02-24 7:22 pm #19 Why is that odd? Are you sure someone else wasn't in there. sent from my RF T1000 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-24 8:14 pm #20 2012-02-24 8:14 pm #20 One is probably for the small transformer. The other for the rails supply. ••• More options Share 1 2 Next 1 of 2 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio US Amps VLX3DE Top Bottom
T timwebb Member Joined 2010 2012-02-23 9:29 am #6 2012-02-23 9:29 am #6 ive traced it back to this diode but cant find the data sheet on it Attachments IMG_20120223_031227.jpg 376.7 KB · Views: 68 ••• More options Share T timwebb Member Joined 2010 2012-02-23 11:25 am #7 2012-02-23 11:25 am #7 Ok. I found it...trying to work on something half sleep. Anyway the diode is us1m-e3. It read 1.5 with diode check. Its connected to pin 12. ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-23 12:47 pm #8 2012-02-23 12:47 pm #8 I think that diode is likely across the relay coil (confirm). If so, you need to follow the trace back farther, possibly all of the way back to the remote turn-on terminal. ••• More options Share T timwebb Member Joined 2010 2012-02-23 1:23 pm #9 2012-02-23 1:23 pm #9 I think pin 8 and 12 are connected.the trace for pin 12 goes under the 494. Those the only two pins I read 0 ohms. I'm think the trace leads to the other driver card. ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-23 9:03 pm #10 2012-02-23 9:03 pm #10 You should read 0 ohms between 8 and 11. You'll have to follow it back farther. The trace may go to the other driver board but it may also go somewhere else. The other driver card isn't likely the source of power. ••• More options Share H Hexhclass Member Joined 2010 2012-02-24 1:36 am #11 2012-02-24 1:36 am #11 That 8 pin IC in the pic is that a hole in it? ••• More options Share T timwebb Member Joined 2010 2012-02-24 2:06 am #12 2012-02-24 2:06 am #12 which one? i got the amp to power up now ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:03 am #13 2012-02-24 7:03 am #13 The ic from your diode pic^^^^^^ sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 9:17 am #14 2012-02-24 9:17 am #14 its a clear hard substance on it maybe flux. ••• More options Share T timwebb Member Joined 2010 2012-02-24 12:47 pm #15 2012-02-24 12:47 pm #15 What's weird is this amp has two 494s controlling the amp. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 1:34 pm #16 2012-02-24 1:34 pm #16 It has 4 supplies, do they split two for the upper rail and two for the lower? sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:34 pm #17 2012-02-24 5:34 pm #17 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:51 pm #18 2012-02-24 5:51 pm #18 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:22 pm #19 2012-02-24 7:22 pm #19 Why is that odd? Are you sure someone else wasn't in there. sent from my RF T1000 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-24 8:14 pm #20 2012-02-24 8:14 pm #20 One is probably for the small transformer. The other for the rails supply. ••• More options Share 1 2 Next 1 of 2 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio US Amps VLX3DE Top Bottom
T timwebb Member Joined 2010 2012-02-23 11:25 am #7 2012-02-23 11:25 am #7 Ok. I found it...trying to work on something half sleep. Anyway the diode is us1m-e3. It read 1.5 with diode check. Its connected to pin 12. ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-23 12:47 pm #8 2012-02-23 12:47 pm #8 I think that diode is likely across the relay coil (confirm). If so, you need to follow the trace back farther, possibly all of the way back to the remote turn-on terminal. ••• More options Share T timwebb Member Joined 2010 2012-02-23 1:23 pm #9 2012-02-23 1:23 pm #9 I think pin 8 and 12 are connected.the trace for pin 12 goes under the 494. Those the only two pins I read 0 ohms. I'm think the trace leads to the other driver card. ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-23 9:03 pm #10 2012-02-23 9:03 pm #10 You should read 0 ohms between 8 and 11. You'll have to follow it back farther. The trace may go to the other driver board but it may also go somewhere else. The other driver card isn't likely the source of power. ••• More options Share H Hexhclass Member Joined 2010 2012-02-24 1:36 am #11 2012-02-24 1:36 am #11 That 8 pin IC in the pic is that a hole in it? ••• More options Share T timwebb Member Joined 2010 2012-02-24 2:06 am #12 2012-02-24 2:06 am #12 which one? i got the amp to power up now ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:03 am #13 2012-02-24 7:03 am #13 The ic from your diode pic^^^^^^ sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 9:17 am #14 2012-02-24 9:17 am #14 its a clear hard substance on it maybe flux. ••• More options Share T timwebb Member Joined 2010 2012-02-24 12:47 pm #15 2012-02-24 12:47 pm #15 What's weird is this amp has two 494s controlling the amp. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 1:34 pm #16 2012-02-24 1:34 pm #16 It has 4 supplies, do they split two for the upper rail and two for the lower? sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:34 pm #17 2012-02-24 5:34 pm #17 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:51 pm #18 2012-02-24 5:51 pm #18 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:22 pm #19 2012-02-24 7:22 pm #19 Why is that odd? Are you sure someone else wasn't in there. sent from my RF T1000 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-24 8:14 pm #20 2012-02-24 8:14 pm #20 One is probably for the small transformer. The other for the rails supply. ••• More options Share 1 2 Next 1 of 2 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio US Amps VLX3DE Top Bottom
Ok. I found it...trying to work on something half sleep. Anyway the diode is us1m-e3. It read 1.5 with diode check. Its connected to pin 12.
P Perry Babin Member Joined 2003 bcae1.com 2012-02-23 12:47 pm #8 2012-02-23 12:47 pm #8 I think that diode is likely across the relay coil (confirm). If so, you need to follow the trace back farther, possibly all of the way back to the remote turn-on terminal. ••• More options Share T timwebb Member Joined 2010 2012-02-23 1:23 pm #9 2012-02-23 1:23 pm #9 I think pin 8 and 12 are connected.the trace for pin 12 goes under the 494. Those the only two pins I read 0 ohms. I'm think the trace leads to the other driver card. ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-23 9:03 pm #10 2012-02-23 9:03 pm #10 You should read 0 ohms between 8 and 11. You'll have to follow it back farther. The trace may go to the other driver board but it may also go somewhere else. The other driver card isn't likely the source of power. ••• More options Share H Hexhclass Member Joined 2010 2012-02-24 1:36 am #11 2012-02-24 1:36 am #11 That 8 pin IC in the pic is that a hole in it? ••• More options Share T timwebb Member Joined 2010 2012-02-24 2:06 am #12 2012-02-24 2:06 am #12 which one? i got the amp to power up now ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:03 am #13 2012-02-24 7:03 am #13 The ic from your diode pic^^^^^^ sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 9:17 am #14 2012-02-24 9:17 am #14 its a clear hard substance on it maybe flux. ••• More options Share T timwebb Member Joined 2010 2012-02-24 12:47 pm #15 2012-02-24 12:47 pm #15 What's weird is this amp has two 494s controlling the amp. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 1:34 pm #16 2012-02-24 1:34 pm #16 It has 4 supplies, do they split two for the upper rail and two for the lower? sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:34 pm #17 2012-02-24 5:34 pm #17 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:51 pm #18 2012-02-24 5:51 pm #18 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:22 pm #19 2012-02-24 7:22 pm #19 Why is that odd? Are you sure someone else wasn't in there. sent from my RF T1000 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-24 8:14 pm #20 2012-02-24 8:14 pm #20 One is probably for the small transformer. The other for the rails supply. ••• More options Share 1 2 Next 1 of 2 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio US Amps VLX3DE Top Bottom
I think that diode is likely across the relay coil (confirm). If so, you need to follow the trace back farther, possibly all of the way back to the remote turn-on terminal.
T timwebb Member Joined 2010 2012-02-23 1:23 pm #9 2012-02-23 1:23 pm #9 I think pin 8 and 12 are connected.the trace for pin 12 goes under the 494. Those the only two pins I read 0 ohms. I'm think the trace leads to the other driver card. ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-23 9:03 pm #10 2012-02-23 9:03 pm #10 You should read 0 ohms between 8 and 11. You'll have to follow it back farther. The trace may go to the other driver board but it may also go somewhere else. The other driver card isn't likely the source of power. ••• More options Share H Hexhclass Member Joined 2010 2012-02-24 1:36 am #11 2012-02-24 1:36 am #11 That 8 pin IC in the pic is that a hole in it? ••• More options Share T timwebb Member Joined 2010 2012-02-24 2:06 am #12 2012-02-24 2:06 am #12 which one? i got the amp to power up now ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:03 am #13 2012-02-24 7:03 am #13 The ic from your diode pic^^^^^^ sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 9:17 am #14 2012-02-24 9:17 am #14 its a clear hard substance on it maybe flux. ••• More options Share T timwebb Member Joined 2010 2012-02-24 12:47 pm #15 2012-02-24 12:47 pm #15 What's weird is this amp has two 494s controlling the amp. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 1:34 pm #16 2012-02-24 1:34 pm #16 It has 4 supplies, do they split two for the upper rail and two for the lower? sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:34 pm #17 2012-02-24 5:34 pm #17 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:51 pm #18 2012-02-24 5:51 pm #18 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:22 pm #19 2012-02-24 7:22 pm #19 Why is that odd? Are you sure someone else wasn't in there. sent from my RF T1000 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-24 8:14 pm #20 2012-02-24 8:14 pm #20 One is probably for the small transformer. The other for the rails supply. ••• More options Share 1 2 Next 1 of 2 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio US Amps VLX3DE Top Bottom
I think pin 8 and 12 are connected.the trace for pin 12 goes under the 494. Those the only two pins I read 0 ohms. I'm think the trace leads to the other driver card.
P Perry Babin Member Joined 2003 bcae1.com 2012-02-23 9:03 pm #10 2012-02-23 9:03 pm #10 You should read 0 ohms between 8 and 11. You'll have to follow it back farther. The trace may go to the other driver board but it may also go somewhere else. The other driver card isn't likely the source of power. ••• More options Share H Hexhclass Member Joined 2010 2012-02-24 1:36 am #11 2012-02-24 1:36 am #11 That 8 pin IC in the pic is that a hole in it? ••• More options Share T timwebb Member Joined 2010 2012-02-24 2:06 am #12 2012-02-24 2:06 am #12 which one? i got the amp to power up now ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:03 am #13 2012-02-24 7:03 am #13 The ic from your diode pic^^^^^^ sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 9:17 am #14 2012-02-24 9:17 am #14 its a clear hard substance on it maybe flux. ••• More options Share T timwebb Member Joined 2010 2012-02-24 12:47 pm #15 2012-02-24 12:47 pm #15 What's weird is this amp has two 494s controlling the amp. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 1:34 pm #16 2012-02-24 1:34 pm #16 It has 4 supplies, do they split two for the upper rail and two for the lower? sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:34 pm #17 2012-02-24 5:34 pm #17 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:51 pm #18 2012-02-24 5:51 pm #18 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:22 pm #19 2012-02-24 7:22 pm #19 Why is that odd? Are you sure someone else wasn't in there. sent from my RF T1000 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-24 8:14 pm #20 2012-02-24 8:14 pm #20 One is probably for the small transformer. The other for the rails supply. ••• More options Share 1 2 Next 1 of 2 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio US Amps VLX3DE Top Bottom
You should read 0 ohms between 8 and 11. You'll have to follow it back farther. The trace may go to the other driver board but it may also go somewhere else. The other driver card isn't likely the source of power.
H Hexhclass Member Joined 2010 2012-02-24 1:36 am #11 2012-02-24 1:36 am #11 That 8 pin IC in the pic is that a hole in it? ••• More options Share T timwebb Member Joined 2010 2012-02-24 2:06 am #12 2012-02-24 2:06 am #12 which one? i got the amp to power up now ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:03 am #13 2012-02-24 7:03 am #13 The ic from your diode pic^^^^^^ sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 9:17 am #14 2012-02-24 9:17 am #14 its a clear hard substance on it maybe flux. ••• More options Share T timwebb Member Joined 2010 2012-02-24 12:47 pm #15 2012-02-24 12:47 pm #15 What's weird is this amp has two 494s controlling the amp. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 1:34 pm #16 2012-02-24 1:34 pm #16 It has 4 supplies, do they split two for the upper rail and two for the lower? sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:34 pm #17 2012-02-24 5:34 pm #17 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:51 pm #18 2012-02-24 5:51 pm #18 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:22 pm #19 2012-02-24 7:22 pm #19 Why is that odd? Are you sure someone else wasn't in there. sent from my RF T1000 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-24 8:14 pm #20 2012-02-24 8:14 pm #20 One is probably for the small transformer. The other for the rails supply. ••• More options Share 1 2 Next 1 of 2 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio US Amps VLX3DE Top Bottom
T timwebb Member Joined 2010 2012-02-24 2:06 am #12 2012-02-24 2:06 am #12 which one? i got the amp to power up now ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:03 am #13 2012-02-24 7:03 am #13 The ic from your diode pic^^^^^^ sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 9:17 am #14 2012-02-24 9:17 am #14 its a clear hard substance on it maybe flux. ••• More options Share T timwebb Member Joined 2010 2012-02-24 12:47 pm #15 2012-02-24 12:47 pm #15 What's weird is this amp has two 494s controlling the amp. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 1:34 pm #16 2012-02-24 1:34 pm #16 It has 4 supplies, do they split two for the upper rail and two for the lower? sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:34 pm #17 2012-02-24 5:34 pm #17 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:51 pm #18 2012-02-24 5:51 pm #18 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:22 pm #19 2012-02-24 7:22 pm #19 Why is that odd? Are you sure someone else wasn't in there. sent from my RF T1000 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-24 8:14 pm #20 2012-02-24 8:14 pm #20 One is probably for the small transformer. The other for the rails supply. ••• More options Share 1 2 Next 1 of 2 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio US Amps VLX3DE Top Bottom
B brandes.cm Member Joined 2009 2012-02-24 7:03 am #13 2012-02-24 7:03 am #13 The ic from your diode pic^^^^^^ sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 9:17 am #14 2012-02-24 9:17 am #14 its a clear hard substance on it maybe flux. ••• More options Share T timwebb Member Joined 2010 2012-02-24 12:47 pm #15 2012-02-24 12:47 pm #15 What's weird is this amp has two 494s controlling the amp. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 1:34 pm #16 2012-02-24 1:34 pm #16 It has 4 supplies, do they split two for the upper rail and two for the lower? sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:34 pm #17 2012-02-24 5:34 pm #17 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:51 pm #18 2012-02-24 5:51 pm #18 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:22 pm #19 2012-02-24 7:22 pm #19 Why is that odd? Are you sure someone else wasn't in there. sent from my RF T1000 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-24 8:14 pm #20 2012-02-24 8:14 pm #20 One is probably for the small transformer. The other for the rails supply. ••• More options Share 1 2 Next 1 of 2 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio US Amps VLX3DE
T timwebb Member Joined 2010 2012-02-24 9:17 am #14 2012-02-24 9:17 am #14 its a clear hard substance on it maybe flux. ••• More options Share T timwebb Member Joined 2010 2012-02-24 12:47 pm #15 2012-02-24 12:47 pm #15 What's weird is this amp has two 494s controlling the amp. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 1:34 pm #16 2012-02-24 1:34 pm #16 It has 4 supplies, do they split two for the upper rail and two for the lower? sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:34 pm #17 2012-02-24 5:34 pm #17 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:51 pm #18 2012-02-24 5:51 pm #18 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:22 pm #19 2012-02-24 7:22 pm #19 Why is that odd? Are you sure someone else wasn't in there. sent from my RF T1000 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-24 8:14 pm #20 2012-02-24 8:14 pm #20 One is probably for the small transformer. The other for the rails supply. ••• More options Share 1 2 Next 1 of 2 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link Home General Interest Car Audio US Amps VLX3DE
T timwebb Member Joined 2010 2012-02-24 12:47 pm #15 2012-02-24 12:47 pm #15 What's weird is this amp has two 494s controlling the amp. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 1:34 pm #16 2012-02-24 1:34 pm #16 It has 4 supplies, do they split two for the upper rail and two for the lower? sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:34 pm #17 2012-02-24 5:34 pm #17 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:51 pm #18 2012-02-24 5:51 pm #18 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:22 pm #19 2012-02-24 7:22 pm #19 Why is that odd? Are you sure someone else wasn't in there. sent from my RF T1000 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-24 8:14 pm #20 2012-02-24 8:14 pm #20 One is probably for the small transformer. The other for the rails supply. ••• More options Share 1 2 Next 1 of 2 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link
B brandes.cm Member Joined 2009 2012-02-24 1:34 pm #16 2012-02-24 1:34 pm #16 It has 4 supplies, do they split two for the upper rail and two for the lower? sent from my RF T1000 ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:34 pm #17 2012-02-24 5:34 pm #17 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:51 pm #18 2012-02-24 5:51 pm #18 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:22 pm #19 2012-02-24 7:22 pm #19 Why is that odd? Are you sure someone else wasn't in there. sent from my RF T1000 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-24 8:14 pm #20 2012-02-24 8:14 pm #20 One is probably for the small transformer. The other for the rails supply. ••• More options Share 1 2 Next 1 of 2 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link
T timwebb Member Joined 2010 2012-02-24 5:34 pm #17 2012-02-24 5:34 pm #17 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share T timwebb Member Joined 2010 2012-02-24 5:51 pm #18 2012-02-24 5:51 pm #18 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:22 pm #19 2012-02-24 7:22 pm #19 Why is that odd? Are you sure someone else wasn't in there. sent from my RF T1000 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-24 8:14 pm #20 2012-02-24 8:14 pm #20 One is probably for the small transformer. The other for the rails supply. ••• More options Share 1 2 Next 1 of 2 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link
T timwebb Member Joined 2010 2012-02-24 5:51 pm #18 2012-02-24 5:51 pm #18 Its set up weird.but I'm sure that it. It uses irfz48 which I thought was odd. ••• More options Share B brandes.cm Member Joined 2009 2012-02-24 7:22 pm #19 2012-02-24 7:22 pm #19 Why is that odd? Are you sure someone else wasn't in there. sent from my RF T1000 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-24 8:14 pm #20 2012-02-24 8:14 pm #20 One is probably for the small transformer. The other for the rails supply. ••• More options Share 1 2 Next 1 of 2 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button. Share: Facebook Twitter Reddit Pinterest Tumblr WhatsApp Email Share Link
B brandes.cm Member Joined 2009 2012-02-24 7:22 pm #19 2012-02-24 7:22 pm #19 Why is that odd? Are you sure someone else wasn't in there. sent from my RF T1000 ••• More options Share P Perry Babin Member Joined 2003 bcae1.com 2012-02-24 8:14 pm #20 2012-02-24 8:14 pm #20 One is probably for the small transformer. The other for the rails supply. ••• More options Share 1 2 Next 1 of 2 Go to page Go Next Last Show hidden low quality content Status This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button.
P Perry Babin Member Joined 2003 bcae1.com 2012-02-24 8:14 pm #20 2012-02-24 8:14 pm #20 One is probably for the small transformer. The other for the rails supply. ••• More options Share