Hello
I have bought an old amplifier Blaupunkt GTA 400 for 20 euros
i change 4 mosfet to the SMPS supply because 1 was burnt....
the sound of this amp is verry bad, so i keep only the smps to build my own amplifier
but i need to change other components because i can here a zzzz when the amp is power on without music
I think the noise is due to the rust on the resistance
the resistor is a 22 ohms and it comes verry hot when the supply works i don't know why ? can someone can explain me that please ?
I surrounded the rust on the resistor
This is the power supply with other condensators
i use 2 condensators of 10000µF low ESR for the secondary
2 condensators of 2200µF for the primary and 1 condensator of 1000µF near the terminals to replace the old condensator
I search the schematic of this amp, if someone have it can you give me please ?
Thanks in advance
hervé
I have bought an old amplifier Blaupunkt GTA 400 for 20 euros
i change 4 mosfet to the SMPS supply because 1 was burnt....
the sound of this amp is verry bad, so i keep only the smps to build my own amplifier
but i need to change other components because i can here a zzzz when the amp is power on without music
I think the noise is due to the rust on the resistance
the resistor is a 22 ohms and it comes verry hot when the supply works i don't know why ? can someone can explain me that please ?
I surrounded the rust on the resistor
An externally hosted image should be here but it was not working when we last tested it.
This is the power supply with other condensators
i use 2 condensators of 10000µF low ESR for the secondary
2 condensators of 2200µF for the primary and 1 condensator of 1000µF near the terminals to replace the old condensator
An externally hosted image should be here but it was not working when we last tested it.
I search the schematic of this amp, if someone have it can you give me please ?
Thanks in advance
hervé
it seems my photos don't appears on the forum
i post another
the rust on the resistor and i mesure the temperature and i have musered 75°C on it but the supply works is it normal
the smps supply
Thanks for your help
i post another
the rust on the resistor and i mesure the temperature and i have musered 75°C on it but the supply works is it normal
An externally hosted image should be here but it was not working when we last tested it.
the smps supply
An externally hosted image should be here but it was not working when we last tested it.
Thanks for your help
hello
Thanks for your answer
this is a photo
a photo where are solder the resistor who are verry hot 75 °C
The C is condensators with a value of 0.1µF "i think " on the condensator i can see 0.1 J 63 so i think 0.1µF 63 V ?
and i would like to know how can i do to have a +/-12 volts to power a preamp please?
Thanks for your answer
this is a photo
An externally hosted image should be here but it was not working when we last tested it.
a photo where are solder the resistor who are verry hot 75 °C
The C is condensators with a value of 0.1µF "i think " on the condensator i can see 0.1 J 63 so i think 0.1µF 63 V ?
An externally hosted image should be here but it was not working when we last tested it.
and i would like to know how can i do to have a +/-12 volts to power a preamp please?
The snubber resistors will run hot but they may be running hotter than normal due to the two missing caps. From what I can see in the photos, there is one 2200uf on each side of the inductor. That leaves only one on the transformer's primary. That could cause more ringing on the primary which could cause the snubber resistors to run hotter.
The simplest option for the regulated preamp supply would be to use 7812 and 7912 regulators (if you want 12v instead of 15v).
The caps are 0.1uF@63 ±5%. Have you confirmed that they're not shorted?
The simplest option for the regulated preamp supply would be to use 7812 and 7912 regulators (if you want 12v instead of 15v).
The caps are 0.1uF@63 ±5%. Have you confirmed that they're not shorted?
Thanks Perry
i will put the 2 missing condensators, but they are hot before i remove the 2 condensators so is it normal that resistors are hot ? and why?
Can you explain me what is the function of theses resistors please ?
for the capacitor i think there are ok i change them but i haven't tools to test them....
the preamp is this product
the aop are NE-5532 but i can change them and i put OPA2134PA from burr brown
Préamplification - Module Préamplificateur Buffer Stéréo AOP NE-5532
it works with a +/-15 V but i don't know the consump in A
Thanks for your help
i will put the 2 missing condensators, but they are hot before i remove the 2 condensators so is it normal that resistors are hot ? and why?
Can you explain me what is the function of theses resistors please ?
for the capacitor i think there are ok i change them but i haven't tools to test them....
the preamp is this product
the aop are NE-5532 but i can change them and i put OPA2134PA from burr brown
Préamplification - Module Préamplificateur Buffer Stéréo AOP NE-5532
it works with a +/-15 V but i don't know the consump in A
Thanks for your help
The missing caps were getting hot?
The snubbers (RC network) are used to damp ringing on the transformer. Under normal operating conditions, they will operate at slightly elevated temperatures. 75C is hotter than normal but, in some amps, they run that hot.
The 5532 is a perfectly good op-amp. There's no reason to change it. Current consumption of most op-amps used for preamp audio have negligible current draw unless you have a large number of them.
The snubbers (RC network) are used to damp ringing on the transformer. Under normal operating conditions, they will operate at slightly elevated temperatures. 75C is hotter than normal but, in some amps, they run that hot.
The 5532 is a perfectly good op-amp. There's no reason to change it. Current consumption of most op-amps used for preamp audio have negligible current draw unless you have a large number of them.
the missing caps are not hot but they are old i'll change them with the same 2200µF because they are in // on the circuit
I change the NE 5532 because the sound was not clear with it but now with the burr brown it's better
This supply power up 4 channel amplifier
do you think i can use it with 2 module like that ?
PSC-Audio | Module PsC-Audio | FET100 - 100W @ 4Ohm; 65W @ 8Ohm ± 45V; 0,1%THD
the maximum current consump is 3 A by amp
the manual in *.pdf
http://www.psc-audio.ro/catalog/html/fet100/FET100_print.pdf
Thanks
I change the NE 5532 because the sound was not clear with it but now with the burr brown it's better
This supply power up 4 channel amplifier
do you think i can use it with 2 module like that ?
PSC-Audio | Module PsC-Audio | FET100 - 100W @ 4Ohm; 65W @ 8Ohm ± 45V; 0,1%THD
the maximum current consump is 3 A by amp
the manual in *.pdf
http://www.psc-audio.ro/catalog/html/fet100/FET100_print.pdf
Thanks
If the audio wasn't clean from the 5532, it was defective or there was a problem with its power supply or the circuit it was in. No one can hear the distortion produced by a 5532 in a properly designed circuit. For those who want to argue this point, you'll have to go elsewhere. I won't be dragged into a senseless discussion. Douglas Self published distortion curves showing that it produced less than 0.001% THD + noise, even when loaded to 500 ohms (tough load for an op-amp).
What is the rail voltage produced by this power supply?
If it's more than 35v, you'll have to do something to drop the voltage before it's fed into the 7815/7915 regulators.
I wouldn't use this supply for much more than ~200 watts if you're going to drive the amps hard for long periods of time.
What is the rail voltage produced by this power supply?
If it's more than 35v, you'll have to do something to drop the voltage before it's fed into the 7815/7915 regulators.
I wouldn't use this supply for much more than ~200 watts if you're going to drive the amps hard for long periods of time.
Hello
Thanks Perry for your help it's nice
for the 5532 when i say the audio wasn't clean, I meant the sound isn't detailed but works fine without distortion.
So i change it with 2 OPA2134 from burr brown and i prefer this sound
the rail voltage with the supply is +/- 25 Volts
for the amp i'll put this simple mono modul
SELECTRONIC ::: L'univers électronique :::
Power RMS on 8 ohms 70 W on 4 ohms 100W
Dist 0.02% @ 1KHz/10W
Damping factor: > 800
sensibility: 0.6Vrms
signal to noise ratio: 115dB
frequency reponse: 3Hz à 200KHz (-3dB)
recommended power supply: 2 x 25 V to 30V / 120VA
Do you think it's a good amp?
Thanks
Thanks Perry for your help it's nice
for the 5532 when i say the audio wasn't clean, I meant the sound isn't detailed but works fine without distortion.
So i change it with 2 OPA2134 from burr brown and i prefer this sound
the rail voltage with the supply is +/- 25 Volts
for the amp i'll put this simple mono modul
SELECTRONIC ::: L'univers électronique :::
Power RMS on 8 ohms 70 W on 4 ohms 100W
Dist 0.02% @ 1KHz/10W
Damping factor: > 800
sensibility: 0.6Vrms
signal to noise ratio: 115dB
frequency reponse: 3Hz à 200KHz (-3dB)
recommended power supply: 2 x 25 V to 30V / 120VA
Do you think it's a good amp?
Thanks
Hello Perry
Thanks
I have two of this amp velleman and they works fine but i just need advices of i can choose a amp like that
Hypex - Module amplificateur Hypex UCD180ST 180W
I have a question perry
i have seen a car amp
Grandes marques autoradio sono navigation - A1 Competition argent - Mono - AMPLI - AUDIO - promotions car audio subwoofer sono tuning ampli gps
on this amp we can set the damping factor 50 to 1800
can you explain me how is it possible ? and is it possible to tweak an ampfier to increase its damping factor and how ?
Thanks a lot
Thanks
I have two of this amp velleman and they works fine but i just need advices of i can choose a amp like that
Hypex - Module amplificateur Hypex UCD180ST 180W
I have a question perry
i have seen a car amp
Grandes marques autoradio sono navigation - A1 Competition argent - Mono - AMPLI - AUDIO - promotions car audio subwoofer sono tuning ampli gps
on this amp we can set the damping factor 50 to 1800
can you explain me how is it possible ? and is it possible to tweak an ampfier to increase its damping factor and how ?
Thanks a lot
For most amps, it's not easy to change the damping factor. The overall design of the amp determines the damping factor. In most instance, it's unimportant. As soon as you insert a few feet of speaker wire into the circuit, the damping factor drops significantly.
There were a few amps (infinity, kenwood?) that had a second set of terminals that allowed the amp to take the feedback signal directly from the speaker terminals. This increased the effective damping factor significantly because it effectively removed the resistance of the speaker wires.
There were a few amps (infinity, kenwood?) that had a second set of terminals that allowed the amp to take the feedback signal directly from the speaker terminals. This increased the effective damping factor significantly because it effectively removed the resistance of the speaker wires.
ok perry i have replaced 4 capacitors because all are 1000µF and the supply seems to work well and the output voltage is verry stable 2x24.2V at output
the supply is power on for about 10 minutes without noise except the resistor ..
the resistors are very hot 70.2°C at max
do you think i can change them with other
it smell hot
thanks
the supply is power on for about 10 minutes without noise except the resistor ..
the resistors are very hot 70.2°C at max
do you think i can change them with other
it smell hot
thanks
- Status
- This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button.
- Home
- General Interest
- Car Audio
- search schematic Blaupunkt GTA 400