I don't have PIN6
I test all the wires with my tester and tester doesn't sound PIIIIII..
My wires of "control" are 7,8 and 12. I think my pin12 is like PIN6 of other systems.
In this xmas holidays I will open my subwoffer and look for any broken component. I think my problem begin into the amplifier...
Thanks Adrian Vista. I will post my progress here too
I test all the wires with my tester and tester doesn't sound PIIIIII..
My wires of "control" are 7,8 and 12. I think my pin12 is like PIN6 of other systems.
In this xmas holidays I will open my subwoffer and look for any broken component. I think my problem begin into the amplifier...
Thanks Adrian Vista. I will post my progress here too
I could not wait
I opened the subwoffer and have not found anything bad . Here I leave some photos taken of the subwoffer PCB now.
The problem I have now is that when I touch with my finger the signal wires for each of the 5 speakers would have to hear a buzz. Well, that makes it buzz only when I touch the blue wire, which is the center speaker, it is as if the other speakers were not connected ...
The photos:
you can find something bad?
Gallery:
ImageShack -
Direct Links:
http://img300.imageshack.us/img300/4986/19122009339.jpg
http://img42.imageshack.us/img42/4264/19122009340.jpg
http://img300.imageshack.us/img300/659/19122009341.jpg
http://img38.imageshack.us/img38/9837/19122009342.jpg
Thank you.
This is an automatic translation from Spanish to English. Reviewed by me and I think this well written
I opened the subwoffer and have not found anything bad . Here I leave some photos taken of the subwoffer PCB now.
The problem I have now is that when I touch with my finger the signal wires for each of the 5 speakers would have to hear a buzz. Well, that makes it buzz only when I touch the blue wire, which is the center speaker, it is as if the other speakers were not connected ...
The photos:
you can find something bad?
Gallery:
ImageShack -
Direct Links:
http://img300.imageshack.us/img300/4986/19122009339.jpg
http://img42.imageshack.us/img42/4264/19122009340.jpg
http://img300.imageshack.us/img300/659/19122009341.jpg
http://img38.imageshack.us/img38/9837/19122009342.jpg
Thank you.
This is an automatic translation from Spanish to English. Reviewed by me and I think this well written
I have spring clip version but the board with the vga connector looks different
http://i49.tinypic.com/2rgks9g.jpg
on my version pin 12 is from a input
sure you have spring clip version?
or maybe my version is old and they changed some things
http://i49.tinypic.com/2rgks9g.jpg
on my version pin 12 is from a input
sure you have spring clip version?
or maybe my version is old and they changed some things
Last edited:
My speakers are 4 years old.
My subwoffer is like that:
http://www.theinquirer.net/img/6686/logitech_z-5500_01.jpg
Where can I loof for issues? I'm little bit lost..
Thanks!
My subwoffer is like that:
http://www.theinquirer.net/img/6686/logitech_z-5500_01.jpg
Where can I loof for issues? I'm little bit lost..
Thanks!
post a image like firs but with the other side
is another way to turn on the amps
to connect the white wire(on my system) to +8v
if not working you must connect the white with black wire to gnd and it will work
take care when i turnned on the tda's and the stabilizer was heating fast
is another way to turn on the amps
to connect the white wire(on my system) to +8v
if not working you must connect the white with black wire to gnd and it will work
take care when i turnned on the tda's and the stabilizer was heating fast
http://img69.imageshack.us/img69/4986/19122009339.jpg
Try this disconnect that wire from board
Connect pin 12 to gnd(pin 13)
the disconnected wire connect-it to +8v
see if all channels have sound
this works in my version
Try this disconnect that wire from board
Connect pin 12 to gnd(pin 13)
the disconnected wire connect-it to +8v
see if all channels have sound
this works in my version
Last edited:
I have to dessold this wire?? but if I dessold this wire and then connect to the same wire to GND there is no conection no?
Wire dessolated ------------------ GND
There is no sound . I have connected all the wires to the pod but signal wires no. Now, I can turn ON the speakers correctly, but if I touch the signal wires the speakers doesn't buzz! :S. I don't know what's wrong...
Thanks.
Wire dessolated ------------------ GND
There is no sound . I have connected all the wires to the pod but signal wires no. Now, I can turn ON the speakers correctly, but if I touch the signal wires the speakers doesn't buzz! :S. I don't know what's wrong...
Thanks.
If I connect the blue wire (i think is PIN8) All the speakers sound, incude the subwoffer. And they are buzzing, buuuuuuuuuuuuu....
And with this wire, if I touch any signal wire, the speaker of this wire sounds PFPFFFFfffPFP . And the same for the subwoffer.
To eliminate this buuuuuuuu.... I have to connect the subwoffer signal to gnd or any signal and this buuuuuu.. disapear. I have to buy a 10kpot for subwoffer signal.
Thanks!
And with this wire, if I touch any signal wire, the speaker of this wire sounds PFPFFFFfffPFP . And the same for the subwoffer.
To eliminate this buuuuuuuu.... I have to connect the subwoffer signal to gnd or any signal and this buuuuuu.. disapear. I have to buy a 10kpot for subwoffer signal.
Thanks!
- Home
- Amplifiers
- Chip Amps
- Hacking the Logitech Z5500