A while back I bought a bunch of these tubes and sockets and put them aside awaiting time and motivation to use them. I am now at a point where I'd like to put them to use. I'd like to build a PP amp preferably using octal support tubes. I've done a bit of searching here and on Google and found a few interesting things but none yet that scream "build me". I've also looked at a few classic KT88 designs to possibly modify. I figured it would be best to post here before I get to far along and get some input from people with experience with these.
Does anyone have any sage advice or any favorite PP amp designs for these?
Thanks,
Dave
Does anyone have any sage advice or any favorite PP amp designs for these?
Thanks,
Dave
Maybe if you use Google or Babel to translate this....unless you read german?
I do, and this looks like a well worked project, but that's all I know about it, except the designer seems to have a name in Germany....
Gegentakt-Verstärker in AB-Betrieb fuer GU 50
I do, and this looks like a well worked project, but that's all I know about it, except the designer seems to have a name in Germany....
Gegentakt-Verstärker in AB-Betrieb fuer GU 50
Last edited:
First of all, you need to think about output and power transformers, before thinking about octal tubes. GU-50 amp needs 8K P-P tranny capable of 100 Watt on rated bandwidth. It is not so easy to get good transformers with such parameters.
Also, you will need 12V 4A for filaments, 250-300V for screen grids and 700-900V for plates.
Are you scared already?
Also, you will need 12V 4A for filaments, 250-300V for screen grids and 700-900V for plates.
Are you scared already?
Last edited:
I did not mean high voltages; I meant very unusual transformers.
GU-50 sound like a charm in my amps. I don't have a complete schematic drawn, they have almost directly coupled drivers with servo, parallel feedback by voltage across output tubes, and regulated voltages for screen grids and drivers.
www.wavebourn.com • View topic - Pyramid-VII: home stereo vacuum tube amp
GU-50 sound like a charm in my amps. I don't have a complete schematic drawn, they have almost directly coupled drivers with servo, parallel feedback by voltage across output tubes, and regulated voltages for screen grids and drivers.
www.wavebourn.com • View topic - Pyramid-VII: home stereo vacuum tube amp
Try this one:
Google Translate
Seite 1 Startseite
Wavebourn: What do you think about this one. Maybe you could help us figure out how to make these transformers (for US) or better yet separate them (power xfmrs) into several smaller (modular type psu).?? I KNOW you've the skill and talent for it!!! Or use it as a launching platform for a different design here... maybe even group buy project? OHHHHHHHHHHHHHH, GU-50 OTLs.... now that's to drool for!!
Google Translate
Seite 1 Startseite
Wavebourn: What do you think about this one. Maybe you could help us figure out how to make these transformers (for US) or better yet separate them (power xfmrs) into several smaller (modular type psu).?? I KNOW you've the skill and talent for it!!! Or use it as a launching platform for a different design here... maybe even group buy project? OHHHHHHHHHHHHHH, GU-50 OTLs.... now that's to drool for!!
Last edited:
I ordered my transformers from EDCOR Electronics Corporation
I can draw full schematic of my Pyramid-VII, but I'm short of time currently. I even wanted to write an article for Elektor magazine about it, probably I will do that later.
I can draw full schematic of my Pyramid-VII, but I'm short of time currently. I even wanted to write an article for Elektor magazine about it, probably I will do that later.
Maybe if you use Google or Babel to translate this....unless you read german?
I do, and this looks like a well worked project, but that's all I know about it, except the designer seems to have a name in Germany....
Gegentakt-Verstärker in AB-Betrieb fuer GU 50
Google Translate
First of all, you need to think about output and power transformers, before thinking about octal tubes. GU-50 amp needs 8K P-P tranny capable of 100 Watt on rated bandwidth. It is not so easy to get good transformers with such parameters.
Also, you will need 12V 4A for filaments, 250-300V for screen grids and 700-900V for plates.
Are you scared already?
What do you think of GU-50 designs with around 400 volt on the plates en 5K or 6K outputtransformers ?
Tubes for input and drive are 2 dissimilar duo-triode13DR7 with inter-stage transformers (1+1:1+1; 10k:2,5k+2,5k; my own construction, calculated and winding in my hoby room).
I still have not the whole scheme drawn, but I will show you very soon.
Currently I'm looking for a suitable analogue VU-meter (large, but not too expensive!), and the entire project was temporarily stopped.
I still have not the whole scheme drawn, but I will show you very soon.
Currently I'm looking for a suitable analogue VU-meter (large, but not too expensive!), and the entire project was temporarily stopped.
Last edited:
I still have the whole scheme drawn, but I will show you very soon.
I look forward to see that.
What do you think of GU-50 designs with around 400 volt on the plates en 5K or 6K outputtransformers ?
I am curious too! Had something like this in planning...
GU-50 is copy of Telefunken LS50.
GU-50 - Wikipedia, the free encyclopedia
http://frank.pocnet.net/sheets/043/l/LS50.pdf
Simple and relatively low voltage (+Ub = 400V) version of GU-50 PP.
This uses budget OPT Indel TGL40/001.
GU-50 - Wikipedia, the free encyclopedia
http://frank.pocnet.net/sheets/043/l/LS50.pdf
Simple and relatively low voltage (+Ub = 400V) version of GU-50 PP.
This uses budget OPT Indel TGL40/001.
Attachments
Last edited:
- Status
- This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button.
- Home
- Amplifiers
- Tubes / Valves
- GU-50 PP amp project - Any favs?