After trawling through many threads here and elsewhere, I decided to have a go at building a nice pair of speakers for my nearfield desk setup. I have a pair of small monitor now, but I wanted something a bit more snazzy, and I love to do a little DIY every now and then.
To have a good pair of speakers for the music I like to listen to at work (mainly light classical music) I settled on a full range design, to mitigate some of the directionality and tweeter sharpness I find rather annoying in my current set-up. I selected the Markaudio CHR-70 for looks, good reviews and forgiving characteristics for first-time builders, and, being a total n00b in the matter, I just picked the design on the Markaudio site that would fit my desk.
Without much further ado:
Drivers:
IMG_3882 by https://www.flickr.com/photos/ctjr/, on Flickr
Taping up the wood. I ordered some great ply from a guy that specialises in flight cases, but saws speaker wood on the side. Amazing quality stuff: straight, cuts right on spec and a lot more plies than at the hardware store. No voids so far and pretty faces on some of the pieces.
IMG_3874 by https://www.flickr.com/photos/ctjr/, on Flickr
Glueing (this is a dry run, but fit was good):
IMG_3875 by https://www.flickr.com/photos/ctjr/, on Flickr
Stain test. No fancy veneers on my first build, just some nice wood oil. Looks real good:
IMG_3876 by https://www.flickr.com/photos/ctjr/, on Flickr
Sealing the box:
IMG_4076 by https://www.flickr.com/photos/ctjr/, on Flickr
Acoustic foam lining:
IMG_4079 by https://www.flickr.com/photos/ctjr/, on Flickr
Next up is routing holes in the faces, mounting the drivers, drill some holes for the terminals and get some push-on connectors for the wiring.
To have a good pair of speakers for the music I like to listen to at work (mainly light classical music) I settled on a full range design, to mitigate some of the directionality and tweeter sharpness I find rather annoying in my current set-up. I selected the Markaudio CHR-70 for looks, good reviews and forgiving characteristics for first-time builders, and, being a total n00b in the matter, I just picked the design on the Markaudio site that would fit my desk.
Without much further ado:
Drivers:
![](https://farm2.staticflickr.com/1690/25966933416_f86621b00b_c.jpg)
Taping up the wood. I ordered some great ply from a guy that specialises in flight cases, but saws speaker wood on the side. Amazing quality stuff: straight, cuts right on spec and a lot more plies than at the hardware store. No voids so far and pretty faces on some of the pieces.
![](https://farm2.staticflickr.com/1710/25966936136_6b9a611019_c.jpg)
Glueing (this is a dry run, but fit was good):
![](https://farm2.staticflickr.com/1544/25872052872_cb8751d1ec_c.jpg)
Stain test. No fancy veneers on my first build, just some nice wood oil. Looks real good:
![](https://farm2.staticflickr.com/1496/25692288550_52b14fe182_c.jpg)
Sealing the box:
![](https://farm2.staticflickr.com/1614/25992845015_9c2b83d60d_c.jpg)
Acoustic foam lining:
![](https://farm2.staticflickr.com/1674/25897888021_e6656d2fd0_c.jpg)
Next up is routing holes in the faces, mounting the drivers, drill some holes for the terminals and get some push-on connectors for the wiring.
Last edited:
Lohengrimas, how are the speakers coming along? You were almost done when you posted.
Easter holidays are keeping me... And I need to make a hole guide for my router. Unknown territory for me, the last time I did any significant woodwork was when I build push karts with my dad
Easter holidays are keeping me... And I need to make a hole guide for my router. Unknown territory for me, the last time I did any significant woodwork was when I build push karts with my dad![]()
I can understand...Spent my Easter holiday playing contractor at home, remodeling my kid's bedroom. To make the holes of my CHR70's I used the following:
1. Inexpensive (MDF is fine, Plywood might last 2 or 3 holes)
2. Mid (I have done approximately 10 holes in 12mm MDF and 13mm Plywood)
3. Expensive
These are good to do holes, but for flush mounting you will need a router. To do holes easily with router, Jasper has a couple of good template tools.
![](https://c2.staticflickr.com/9/8119/29878329321_f49e96f9e7_b.jpg)
Done! this is pre-staining, I'll probably add nothing more than a thin coat of furniture oil.
For those missing the port: it's on the back.
So far, first impressions are mostly positive, except the highs do suffer from some weird defect. There is a slight sibilance, almost like a lisp, on voices, if listened to with a lot of toe in. This largely disappears when reducing toe-in to ) degrees, but for the sake of a coherent soundstage, 15 degrees of toe-in or thereabouts works best.
Bass is surprisingly good for a desktop set up and the imaging is above reproach, the single driver mojo really does work.
Last edited:
Cheap , easy , reasonably good drivers. What's not to like.
Just don't go off bleating that they are better than Sex![]()
You’re right bout sex, sorry admin I know this is not the for but had to agree to him.
- Status
- This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button.
- Home
- Loudspeakers
- Full Range
- First build: Markaudio CHR-70 Bass Reflex