I think you forgot this one in the list.
http://www.creativesound.ca/pdf/plan-alp-10-advanced.pdf
http://www.creativesound.ca/pdf/plan-alp-10-advanced.pdf
Also did a design for the Alpair 10.3 as shown on the plans I have.Which is designed for Alpair 10.2.
dave
Also did a design for the Alpair 10.3 as shown on the plans I have.
do you have a pdf ?
thanks
Posted by Scott yesterday - Miscellaneous designs -Mark Audio, Fostex, TB, Dayton, Seas etc.
Hello,
I am resurrecting this thread because I do not want to open a new one, and I have a question that might fit here.
So, yesterday I became a happy owner of a new pair of 10.3!
Ultimately, I plan to build either a Pensil or an MLTL, but since my woodworking skills are not so advanced, that may take a while...
In the meantime, I had an idea of using some existing BR boxes (some older "Technics" two-way speakers. They use an 8" woofer, but I can build an adaptor to fit the Alpair).
Box external dimensions are 42x25x22 cm, while internal (if I measured correctly) should be around 38.4x21.4x18.4cm.
That results in a volume of around 15L which should be just fine for Alpair 10.3 s...
Where I am getting confused is the port.
It has one in front (see pic).
It has 4cm diameter and is 6 cm long. Can I use the same port, or just prolong it a bit?
If yes, if I use thee same diameter port, what lengh should it be?
Thanks a lot!
Vix
I am resurrecting this thread because I do not want to open a new one, and I have a question that might fit here.
So, yesterday I became a happy owner of a new pair of 10.3!
Ultimately, I plan to build either a Pensil or an MLTL, but since my woodworking skills are not so advanced, that may take a while...
In the meantime, I had an idea of using some existing BR boxes (some older "Technics" two-way speakers. They use an 8" woofer, but I can build an adaptor to fit the Alpair).
Box external dimensions are 42x25x22 cm, while internal (if I measured correctly) should be around 38.4x21.4x18.4cm.
That results in a volume of around 15L which should be just fine for Alpair 10.3 s...
Where I am getting confused is the port.
It has one in front (see pic).
It has 4cm diameter and is 6 cm long. Can I use the same port, or just prolong it a bit?
If yes, if I use thee same diameter port, what lengh should it be?
Thanks a lot!
Vix
Attachments
Thanks Dave.
I know that the box is not ideal, but should do the trick until I get to build something properly.
So, why 10.3?
Well, compromise. Neither the biggest one, nor the smallest. Neither the most expensive, nor the cheapest...
A midddle ground.
(Truth being that I dream of a pair of Lii-18 s in Open Baffle, but that is not doable for the moment, due to the room siz3 and wallet depth limitations)
So, I hope that 10.3 will be goodenough...
Regards from France,
Vix
I know that the box is not ideal, but should do the trick until I get to build something properly.
So, why 10.3?
Well, compromise. Neither the biggest one, nor the smallest. Neither the most expensive, nor the cheapest...
A midddle ground.
(Truth being that I dream of a pair of Lii-18 s in Open Baffle, but that is not doable for the moment, due to the room siz3 and wallet depth limitations)
So, I hope that 10.3 will be goodenough...
Regards from France,
Vix
It is very nice driver. It does take sometime to break in so do get it moving. Your temposary box will be better than the cardboard one sthey come in.
The volume is close, a couple “bricks” (or braces) to shrink the volume would not hurt. 13 litres is near optimum so you are close.
dave
The volume is close, a couple “bricks” (or braces) to shrink the volume would not hurt. 13 litres is near optimum so you are close.
dave
- Home
- Loudspeakers
- Full Range
- Compilation of Alpair 10.3 designs