Go Back   Home > Forums > > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Twisted Pear Superior quality electronic kits

Reply
 
Thread Tools Search this Thread
Old 24th May 2015, 01:33 AM   #21
pawlus is offline pawlus  Canada
diyAudio Member
 
Join Date: Oct 2008
Location: Vancouver BC
Yes - used the through hole option. I checked for signal at the resistors and also checked resistance from the output pads to the input side of the resistors. I have no signal at the resistors and they all measure approximately 33 ohms.
  Reply With Quote
Old 24th May 2015, 12:17 PM   #22
Russ White is offline Russ White  United States
diyAudio Member
 
Russ White's Avatar
 
Join Date: Jan 2005
Location: Nashville, TN, USA
Quote:
Originally Posted by pawlus View Post
Need some help. I've installed my Hermes-Amanero-Cronus. I configured the Amanero using Russ's example without issue and it responds properly during playback. However there is no lock on my BII and checking with a scope I have no output on DCK, D1 or D2 on the Cronus. I have those inputs from the Amanero-Hermes at the Hermes connector on the Cronus and the Rhea clocks are running. Any suggestions as to what to check next?
Which firmware on the Amanero?

Did you check with the scope at the Cronus inputs?

Can you get a picture of the setup - with focus on the cronus?

Cheers!
Russ
__________________
Less pulp more juice Twisted Pear
Audio
/Twisted Pear Audio Blog
  Reply With Quote
Old 24th May 2015, 09:42 PM   #23
pawlus is offline pawlus  Canada
diyAudio Member
 
Join Date: Oct 2008
Location: Vancouver BC
All better now. Turned out to be a cold solder joint on one of the Potato pins. I didn't mention (guess I should've) that I was seeing sporadic activity on the outputs but it wouldn't last and certainly wouldn't allow the DAC to lock. I started to think a cold solder joint based on that this morning. When I started to scope the in/outs on the Potato, I got a lock but that didn't last. Then I took an iron to the Potato pins and everything seems solid. Thanks for the help Russ.
  Reply With Quote
Old 24th May 2015, 11:57 PM   #24
kannan_s is offline kannan_s  United States
diyAudio Member
 
Join Date: Jun 2009
Introducing the Hermes-Amanero Send a message via Yahoo to kannan_s
Where should i use the Resistors R1- R7 (33 Ohm ) in the setup? Also user manual ( simple) should help person like me who needs to go through so many places to find answers?
  Reply With Quote
Old 24th May 2015, 11:58 PM   #25
kannan_s is offline kannan_s  United States
diyAudio Member
 
Join Date: Jun 2009
Introducing the Hermes-Amanero Send a message via Yahoo to kannan_s
I found these resistors in my pack????
  Reply With Quote
Old 25th May 2015, 08:39 PM   #26
pawlus is offline pawlus  Canada
diyAudio Member
 
Join Date: Oct 2008
Location: Vancouver BC
Quote:
Originally Posted by kannan_s View Post
I found these resistors in my pack????
See post #176 in the Cronus thread from Russ.
  Reply With Quote
Old 26th May 2015, 12:30 AM   #27
kannan_s is offline kannan_s  United States
diyAudio Member
 
Join Date: Jun 2009
Introducing the Hermes-Amanero Send a message via Yahoo to kannan_s
What is the correct orientation of plugging the Crystal Oscillator?-
  Reply With Quote
Old 26th May 2015, 01:27 AM   #28
BrianDonegan is offline BrianDonegan  United States
diyAudio Member
 
BrianDonegan's Avatar
 
Join Date: Dec 2004
Location: TPA HQ (The Basement)
Introducing the Hermes-Amanero
Quote:
Originally Posted by kannan_s View Post
What is the correct orientation of plugging the Crystal Oscillator?-
The XO, Rhea and Cronus board each have an alignment dot in one corner.
  Reply With Quote
Old 2nd June 2015, 05:49 PM   #29
ivigueras is offline ivigueras  Spain
diyAudio Member
 
ivigueras's Avatar
 
Join Date: Oct 2006
Introducing the Hermes-Amanero
Hi, Russ & Brian,

I want use the spdif-4 and the sidecar with my amanero & BIII. What would be the best configuration adding the Hermes and Cronus boards?

Regards,
Ignacio
  Reply With Quote
Old 2nd June 2015, 07:32 PM   #30
Russ White is offline Russ White  United States
diyAudio Member
 
Russ White's Avatar
 
Join Date: Jan 2005
Location: Nashville, TN, USA
Just wire the Cronus as a normal I2S source into the sidecar.

Cheers!
Russ
__________________
Less pulp more juice Twisted Pear
Audio
/Twisted Pear Audio Blog
  Reply With Quote

Reply


Introducing the Hermes-AmaneroHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Hermes-BBB/Botic cape for BeagleBone Black Russ White Twisted Pear 656 22nd July 2019 01:53 PM
WTB: amanero board janos_904 Swap Meet 7 10th May 2015 10:50 AM
WTB: Amanero ristar Swap Meet 5 5th December 2014 07:55 AM
amanero merlin2069er Swap Meet 3 19th April 2014 09:32 PM
WTB - Amanero ThuyTN Swap Meet 0 31st January 2013 10:21 AM


New To Site? Need Help?

All times are GMT. The time now is 09:32 AM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 14.29%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright ©1999-2019 diyAudio
Wiki