Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Tubes / Valves All about our sweet vacuum tubes :) Threads about Musical Instrument Amps of all kinds should be in the Instruments & Amps forum

My experience: the cheap punch set VS Greenlee punch
My experience: the cheap punch set VS Greenlee punch
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 21st July 2006, 04:36 PM   #1
vax9000 is offline vax9000  United States
diyAudio Member
Join Date: May 2006
Location: Cleveland
Default My experience: the cheap punch set VS Greenlee punch

Here is my experience.

I bought the cheap punch set from ebay. It has two bolts, 4 dies and 4 nuts. From the photo I guess it is the same set as that from HaborFreight. I punched six 7/8" holes and three 1 3/32" holes on a electric break box. The bolt used with the 7/8" punch was worn to a point that the nut was not straight with the die, and when I was punching the 7th hole the nuts stuck on the edge of the die. I did not notice and I kept turning the bolt. I heard a big sound and the bolt was broken into two pieces.

The bolt used with the 1 3/32" punch was severely worn after three holes. Fortunately I need only 3 big holes for my EL34 amp. I guess it may be able to punch another 3 holes before it dies.

I could not wait 1 week to buy on ebay, so I went to home depot and bought a 0.89mm(roughly 7/8") punch with $30. It is very good. I needed less force to punch the same break box. After 4 holes I observed the bolt and there was no sign of wearing.

This is my experience that might be useful to you guys. I guess the much better cutting edge design is the reason why less force is needed with GreenLee. Maybe the bolt quality is higher too. It well worths the price.

Edit: The break box is made of 1/16" steel sheet. It is the soft type steel often seen with break boxes, not hard steel or stainless steel.
Attached Images
File Type: jpg dscn6002.jpg (72.5 KB, 301 views)
  Reply With Quote
Old 21st July 2006, 05:22 PM   #2
EC8010 is offline EC8010  United Kingdom
diyAudio Moderator Emeritus
EC8010's Avatar
Join Date: Jan 2003
Location: Near London. UK
As you've discovered, cheap tools are more expensive in the long run - you have to replace them with proper tools. In the UK, we have Q-Max punches. Some of mine are twenty five years old.
The loudspeaker: The only commercial Hi-Fi item where a disproportionate part of the budget isn't spent on the box. And the one where it would make a difference...
  Reply With Quote
Old 21st July 2006, 06:22 PM   #3
smoking-amp is offline smoking-amp  United States
diyAudio Member
smoking-amp's Avatar
Join Date: Dec 2001
Location: Hickory, NC
I just checked the Harbor Freight knockout punch set I got and it does indeed have too much slack in the bolt threads. I have used them for a few holes in aluminum and thin steel (baking pans) so far without problem, but looks like they will likely fail on something heavier. I just tried some Greenlee bolts in them, but they do not fit. Wrong thread pitch, so no help there. Its a shame the H-F knockouts aren't made right. I think I will try using a smaller punch (backwards) as a security nut behind a bigger punch, next time I use them, to distribute the forces.

Only other option I can think of would be to bore out the punch thread and use the Greenlee bolt with a big nut behind the punch. (Mouser sells spare Greenlee bolts by the way. $20 for the big ones. Even the Greenlee's break bolts occasionally, but I never had the thread strip out on them.) Likely need a tungsten carbide boring bar to machine the hardened steel punch though.

Another problem with the H-F knockout punch design is that it has four points on the punches, this means 8 cuts occuring in the sheet metal simultaneously (very high forces required). The Greenlees only use two points and they also have a newer (and even more absurdly expensive) design that uses a spiral cutter with only one cutting point. Finally, the H-F kockout punches are not really the right sizes needed for tube sockets anyway (conduit punches).

  Reply With Quote
Old 21st July 2006, 06:34 PM   #4
Tom Bavis is offline Tom Bavis
diyAudio Member
Tom Bavis's Avatar
Join Date: Jun 2002
Location: Macedon NY
GREASE the threads before using ... even on a Greenlee. It'll reduce the torque required and maybe save the bolt a little longer. I've broiken a few Greenlee bolts too...

With the cheap ones, I wouldn't even TRY punching steel - only aluminum.
  Reply With Quote
Old 21st July 2006, 06:36 PM   #5
JohnAtwood is offline JohnAtwood  United States
diyAudio Member
JohnAtwood's Avatar
Join Date: May 2006
Location: Rural Nevada
Default Greenlee punches

I've got Greenlee punches my dad got for me when I was a ham in the 1960s plus I've bought used Greenlee punches at swap meets that look like they came from the 1930s. They all work great, and I never have had to sharpen them. I do occasionally put new grease on the threads and bearing surfaces. I mostly punch aluminum, but have used them on soft steel, too.

A friend turned me on to something new, which works much better than punches: the "Rotabroach". This is a drill-type tool with changeable cutters than comes in sizes from 5/16" to 3/4". My friend got it from Sanp-On, but they should be available other places, too. They make very smooth holes quite easily. I still use the Greenlee punches for the larger sizes.

- John
  Reply With Quote
Old 21st July 2006, 08:52 PM   #6
smoking-amp is offline smoking-amp  United States
diyAudio Member
smoking-amp's Avatar
Join Date: Dec 2001
Location: Hickory, NC
I assume you mean these things:

They do look nice. But they are even more expensive than the outrageous Greenlee prices.
Also it appears that they do not have 3 flats on the shank for a standard drill press chuck (I see a set screw type flat in their picture, may only fit their own special drill presses). And it will take a strong drill press to drive them for the bigger diameters (up to 60 mm, 16 cutting edges).

For up to 3/4 inch I would suggest using stepped drill bits. Some cheap titanium coated ones here:


H-F sells them even cheaper, I haven't tried theirs yet, (plastic?)

  Reply With Quote


My experience: the cheap punch set VS Greenlee punchHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Punch 200.4 PS problem? RJCRAFTS Car Audio 5 25th June 2008 02:21 AM
Selling a punch 250a2, old punch 75, and ppi epx 205 on EBAY ppia600 Swap Meet 0 23rd February 2008 02:17 AM
Punch 800.2 meepers Car Audio 26 16th January 2008 10:32 PM
Rockford Punch 75 (non HD) Clipped Car Audio 8 18th October 2007 11:56 AM
RF Punch 75.2, help plz JSmooth420 Car Audio 5 17th September 2006 11:20 AM

New To Site? Need Help?

All times are GMT. The time now is 09:18 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.00%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright ©1999-2019 diyAudio