
Home  Forums  Rules  Articles  diyAudio Store  Blogs  Gallery  Wiki  Register  Donations  FAQ  Calendar  Search  Today's Posts  Mark Forums Read  Search 
Tubes / Valves All about our sweet vacuum tubes :) Threads about Musical Instrument Amps of all kinds should be in the Instruments & Amps forum 

Please consider donating to help us continue to serve you.
Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving 

Thread Tools  Search this Thread 
9th June 2019, 08:32 PM  #1 
diyAudio Member

Understanding load on triode and impedance matching
Hi,
I've looked around and asked this question in various threads but still haven't fully understood this. The context of the question is that I'm trying to build a 45 based SE headphone amp. Let's assume a standard 5K:8R transfomer is used, and that it would have 2W available to 8ohm speakers. Now, what happens when 32ohm and 300ohm headphones are connected to the 8ohm tap? This is my understanding: If headphones are connected directly, 32ohm will have 500mW and 300ohm will have 50mW. The reflected load on the primaries should ideally be around 5K. When connected directly, the load will be 20K and 187K respectively. OTOH, connecting a 12ohm/3W resistor across the output would "fake" the reflected load to 5.4K7.2K, which seems better. In this case though, how much power is being "wasted" on the load resistor and how much remains for the HP's? I've basically gotten conflicting answers on whether the load resistor is required or not, hence my confusion. Lastly, I would like to understand what are the differences in Voltage swing for the headphones, if they were connected to an 8ohm tap vs. a 32ohm tap. Thanks! 
9th June 2019, 09:00 PM  #2 
diyAudio Member
Join Date: Apr 2011

Can you post the circuit? A resistor in parallel with the load will split the power according to 1/R for each, since power = V^2/R, and V is the same for both.
Last edited by rayma; 9th June 2019 at 09:03 PM. 
9th June 2019, 10:35 PM  #3 
diyAudio Member

The circuit is a Tubelab SE. I don't think there is any NFB.
OK so assuming the same 8ohm output, 32ohm HP  12ohm load resistor gets ~72% of power and 32ohm gets 27%, HP will have 545mW. 300ohm HP gets ~3.8% which is 76mW. If these calculations are correct, then overall power to the HP's seems the same with or without the load resistor, but the reflected load on the triode is different in both cases. Without load resistor, the tube is being "under" worked, while with the load resistor, it's being loaded to full power. Is this correct? If so, which is the preferred scenario? There has to be a "correct" way to do it. 
9th June 2019, 10:39 PM  #4 
diyAudio Member
Join Date: Apr 2011


9th June 2019, 10:41 PM  #5  
diyAudio Member

Quote:
It seems that in terms of overall power it doesnt make much difference, but there is a big difference in terms of the load on the triode. I simply don't know what are the tradeoffs of each approach 

9th June 2019, 10:45 PM  #6 
diyAudio Member
Join Date: Apr 2011

George designed the circuit, so you should best go with his approach. Changing the load moves the load line around, and may limit the available voltage swing, increase distortion, and/or be asymmetrical. Most output transformers are optimized for a particular impedance, and should be used with this in mind.
The power is not an issue, since headphones need little power. Also, a parallel resistor will tend to flatten the impedance curve seen by the amplifier and make it more resistive, which is a good thing, especially for a circuit with highish output impedance and no loop nfb. The voltage output with frequency will then be more flat with a flatter impedance curve. Last edited by rayma; 9th June 2019 at 11:01 PM. 
9th June 2019, 11:15 PM  #7 
diyAudio Member

Thank you, this makes sense.
So, assuming a parallel resistor is used, what would be the difference between using an OPT that is tapped at 8ohm and one with 32ohm? With the 8ohm tap, a 1012 resistor would be used to match impedance. ~47 ohm would be used with a 32ohm tap. Power output would be the same in both cases, right? But, with the 32ohm tap there would be a higher voltage swing. Is this correct? 
9th June 2019, 11:24 PM  #8 
diyAudio Member
Join Date: Apr 2011

Right on both. I suspect that you will prefer the sound one way or the other though, so it try both ways. Using the lower impedance tap (and lower resistor) will result in a flatter impedance curve for a given headphone. The higher impedance tap may have different advantages, like better hf.
Last edited by rayma; 9th June 2019 at 11:29 PM. 
9th June 2019, 11:27 PM  #9 
diyAudio Member

Thanks again!
I still haven't ordered the transformer. The amp will primarily used with high impedance HP's which benefit from a high voltage swing, so I think I'll go ahead with a single 32ohm secondary. Lastly, is there a simplified way to calculate the available voltage? Is it as simple as dividing the output voltage from the triode by the transformer ratio? 
9th June 2019, 11:31 PM  #10  
diyAudio Member
Join Date: Apr 2011

Quote:
If output power is 8W into a load R of 32 ohms, then the rms output voltage is sqrt (8 x 32) = 16 Vrms. Last edited by rayma; 9th June 2019 at 11:41 PM. 

Thread Tools  Search this Thread 


Similar Threads  
Thread  Thread Starter  Forum  Replies  Last Post 
Understanding load lines  merlin el mago  Tubes / Valves  86  6th December 2018 08:08 PM 
EL34,KT66,6L6GC,KT77:who works better with high impedance OT load in SE Triode Mode?  yggit  Tubes / Valves  3  22nd May 2015 07:20 PM 
Understanding load lines  tvrgeek  Tubes / Valves  20  18th January 2010 07:16 PM 
Need help understanding transformer impedance ratios and impedance matching  percy  Tubes / Valves  5  28th February 2005 09:35 PM 
Understanding OPT primary Z and load matching.  percy  Tubes / Valves  4  21st August 2004 01:30 AM 
New To Site?  Need Help? 