Go Back   Home > Forums > >

Tubes / Valves All about our sweet vacuum tubes :) Threads about Musical Instrument Amps of all kinds should be in the Instruments & Amps forum

Direct-Coupled Tube (or Tube-MOSFET) Headphone Amp Circuit
Direct-Coupled Tube (or Tube-MOSFET) Headphone Amp Circuit
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools
Old 8th July 2015, 05:12 PM   #1
TavishDad is offline TavishDad  United States
diyAudio Member
Join Date: Aug 2014
Location: New York
Default Direct-Coupled Tube (or Tube-MOSFET) Headphone Amp Circuit

Hereís an idea for a direct-coupled tube (or tube-MOSFET) headphone amplifier. It is a simple variant on a widely used circuit, so Iím sure something similar is already out there. A DC level shifter allows the circuit to be direct coupled, with the output at 0 V DC, while also allowing the tubes to operate at high voltages (200 V), where they work best. I canít claim any creativity on the level-shifter idea, since similar techniques were used to direct-couple tube operational amplifiers back in the 1950s & 1960s. Back then, neon lamps were used instead of the zener diodes. But I havenít seen this exact circuit for a headphone amplifier before, and it elegantly eliminates the low-frequency phase shift and distortion from an output coupling capacitor or transformer.

The output device could be a MOSFET, a tube, or an NPN. I use high impedance Sennheiser headphones, so the tube output would probably work fine for me, but I suspect the MOSFET or NPN output would have lower distortion. With a negative high-voltage rail, the output device could even be a 6AS7 (although that is getting a little bit impractical for a headphone amp, assuming you want it to be compact).

Note that these 2 attachments are conceptual schematics, drawn to emphasize the direct coupling. I posted a more practical version on the ďdownloadsĒ page of my website, with a modified circuit to control DC offset, along with the required DC offset protection circuits.

Downloads – Tavish Design

I havenít built it yet, but Iím planning to develop a PCB and build it soon. Any suggestions before I do? I assume there are similar circuits out there? How much current is really needed for low impedance headphones? Is there a better output MOSFET than the IRF540? Thoughts about an NPN (or Sziklai) output version? And note, this basic topology could be used to build a direct-coupled hybrid power amplifier as well.

Attached Images
File Type: png headphone_amp_tube_MOSFET.png (39.9 KB, 439 views)
File Type: png headphone_amp_tube_out.png (42.1 KB, 426 views)
  Reply With Quote
Old 28th July 2015, 05:06 PM   #2
IwanS is offline IwanS  United States
diyAudio Member
Join Date: Jul 2015
I came here from your other thread. I personally am more interested in hybrid power amplifiers than headphone amps, so I'm looking at the circuit form that perspective.

I think the level shifters are a good idea, even if not new. For a power amp, one issue with your ckt might be gain. A power amp needs ~20dB gain and you probably want 20dB NFB. But the single tube differential pair will not give 40dB gain, even with the current-mirror load.

What output stage did you have in mind for a power amp?

  Reply With Quote
Old 29th July 2015, 05:34 PM   #3
TavishDad is offline TavishDad  United States
diyAudio Member
Join Date: Aug 2014
Location: New York
Hi Iwan,

Thanks, I think that's a good point - with a single tube gain stage, there is limited loop gain in the amp. I plan to experiment with the stage to see how much gain is possible, but with a 12AX7 and a current mirror load, 35 dB seems reasonable. That would leave about 15dB for feedback, and 20 dB for the gain of the amplifier. If the output stage is sufficiently linear, that might be OK. Many tube amps work with well 15 dB NFB (or even less).

Adding another gain stage would make things much more complicated and detract from the elegant simplicity, I think.

I think the topology would work with almost any single-ended or complementary output stage. For a headphone amp, any of the single-ended stages I showed would work well.

For a very simple hybrid power amplifier, a complementary MOSFET output stage is appealing, since the MOSFETs don't need safe operating area protection. But MOSFETs have low gain and are less linear than BJTs, so one possibility would be a complementary output stage with BJT-MOSFET complementary feedback pairs.

The CFP output stage is quite linear, so it might not need a lot of feedback, which might make it a good choice, given the limited loop gain.

  Reply to this post


Direct-Coupled Tube (or Tube-MOSFET) Headphone Amp CircuitHide this!Advertise here!
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Class A2 Direct MOSFET Coupled SE Michael Koster Tubes / Valves 178 15th June 2018 06:16 PM
GLASS-SAND CLASS A TUBE MOSFET HYBRID HEADPHONE AMP roline Headphone Systems 24 7th November 2013 11:46 PM
Direct-coupled amplifier circuit tca Solid State 4 7th July 2012 01:47 AM
Does this circuit consider a direct coupled amplifier? motbuddy Everything Else 9 29th September 2011 10:29 AM
headphone amp circuit diagram usinga 300b tube arvin Headphone Systems 3 21st May 2007 06:39 AM

New To Site? Need Help?

All times are GMT. The time now is 04:42 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 14.29%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
Copyright ©1999-2021 diyAudio