Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Tubes / Valves All about our sweet vacuum tubes :) Threads about Musical Instrument Amps of all kinds should be in the Instruments & Amps forum

Cathode Biasing a 6L6 quartet power stage
Cathode Biasing a 6L6 quartet power stage
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 7th February 2008, 12:18 PM   #1
Dave Z is offline Dave Z  United States
diyAudio Member
Join Date: Dec 2007
Default Cathode Biasing a 6L6 quartet power stage

I have a tube guitar amp that has 4 6L6's in the 100W power stage. I want to convert it to a Cathode Bias configuration. I have heard two ways of doing this. The first is that ALL of the power tubes would have the cathodes connected together and then have a SINGLE cathode resistor with bypass cap to GND. The second method I've heard is to have the two tubes which are in parallel on the same phase of the output transformer, to run through a common cathode resistor with a bypass cap, and the other two tubes on the other phase run though another common cathode resistor with bypass cap. I was hoping for comments on each method. Are both valid? Tone differences? Matching difficulties? I would be checking the output with a scope and adjusting the bias based on visual illimination of crossover distortion. I want to a point of reference what different levels of crossover distortion sounds like for the dirty channel of the amp

  Reply With Quote
Old 7th February 2008, 01:39 PM   #2
SY is offline SY  United States
On Hiatus
SY's Avatar
Join Date: Oct 2002
Location: Chicagoland
Cathode Biasing a 6L6 quartet power stage
Common cathode resistors generally work best with matched tubes. Otherwise, one tube does more work than the other (push and pull are not symmetric). And idle current mismatches will tend to increase output transformer distortion. This may or may not be desirable in MI amps. You could either have one resistor in common for all tubes, two resistors separate for each side, or even four resistors individual to each tube.

One thing is for sure- the size of the cathode resistor's bypass cap will very much affect tone and overload. That might be the most interesting thing to experiment with.
"You tell me whar a man gits his corn pone, en I'll tell you what his 'pinions is."
  Reply With Quote
Old 7th February 2008, 05:03 PM   #3
tubewade is offline tubewade  United States
diyAudio Member
tubewade's Avatar
Join Date: Jun 2007

S.Y. may correct me. Going to cathode bias will cut your power nearly in half. May be a good thing. It will also move your operating point close to Class A. In Class A both valves are always on and there will be no crossover distortion. If you use a single cathode resistor with nearly perfectly matched valves you can probably dispense with the cathode bypass capacitor. I prefer the sound this way. On the other hand, if you use a separate resistor for each pair of valves, you must use a bypass capacitor on each, but you can use a configuration similar to that in a Williamson amplifier to balance the output stage even with less than perfectly matched valves. As for whether that is necessary in an instrument amp, only you can decide. As S.Y. said, the bypass capacitor and the amount of unbalanced current saturating the core of the transformer will probably have the greatest effect on the tone.


  Reply With Quote


Cathode Biasing a 6L6 quartet power stageHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Biasing a cathode follower? G Tubes / Valves 110 23rd August 2010 03:59 PM
cathode biasing question puginfo Tubes / Valves 7 3rd June 2009 03:24 PM
LED cathode biasing in push-pull input stage exeric Tubes / Valves 14 18th August 2008 01:35 AM
EL84/6BQ5 triode pp with no cathode biasing DrewP Tubes / Valves 19 17th May 2006 12:31 AM

New To Site? Need Help?

All times are GMT. The time now is 09:13 AM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.79%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio