Go Back   Home > Forums > >

Solid State Talk all about solid state amplification.

What causes BJT based amplifier distortion?
What causes BJT based amplifier distortion?
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools
Old 4th February 2021, 07:51 AM   #1
edbarx is offline edbarx  Europe
diyAudio Member
 
edbarx's Avatar
 
Join Date: May 2018
Location: Maltese Archipelago
Default What causes BJT based amplifier distortion?

The obvious answer is active device non-linearity, but this is too generic and abstruct. BJTs have an exponential input characteristic, which means, the more current passes through the base, the easier it is to pass more. The output characteristic, that is, the collector current at a constant base current, is not a horizontal line. It is neither a line with a positive gradient, but a curve albeit with small positive gradients. As if these imperfections were not enough, there is also a voltage dependent capacitance formed by both depletion layers at the emitter-base interface and at the base-collector interface. Since, a transistor silicon chip is thin, the emitter-base depletion layer and the base-collector depletion layers are in close proximity, and the electric field at the latter affects the electric field at the former. All these unwanted characteristics of NPN and PNP doped silicon crystals contribute to a transistor operation that is not simply linear, but depends on device voltages and applied frequencies.

Since, this forum is intended for enthusiasts to build their own amplifiers, I would like those who have primarily the understanding of the concepts to comment. The question is how does amplifier topology circumvent these unwanted transistor properties? I would like the discussion to first consider simple three stage amplifiers, differential inputs, VAS and the power stage including its driver.

Please note, I am not asking to repair my amplifier. That, thanks to this forum, specifically, Mooly and mjona and other contributors, still works and is daily filling my home with beautiful music.
__________________
Any fool can make things bigger, more complex, and more violent. It takes a touch of a genius, and a lot of courage, to move in the opposite direction. [Albert Einstein]

Last edited by edbarx; 4th February 2021 at 08:31 AM.
  Reply With Quote
Old 4th February 2021, 08:00 AM   #2
indra1 is online now indra1  Indonesia
diyAudio Member
 
Join Date: Nov 2010
Location: Bogor
Perhaps Dr. Arto Kolinummi book can shed some light for you. Audio Power Amplfiers - towards inherently linear amplifiers.
  Reply With Quote
Old 4th February 2021, 08:48 AM   #3
nigelwright7557 is offline nigelwright7557  United Kingdom
diyAudio Member
 
nigelwright7557's Avatar
 
Join Date: Apr 2008
Location: Carlisle, England
A transistor doesn't need to be linear as feedback forces it to be linear.
A typical LTP front end just matches output signal to input signal.

The only place this can cause a problem is crossover distortion.
And this has been solved for many years with a bias circuit.
  Reply With Quote
Old 4th February 2021, 09:00 AM   #4
edbarx is offline edbarx  Europe
diyAudio Member
 
edbarx's Avatar
 
Join Date: May 2018
Location: Maltese Archipelago
Thank you for the link. I read the book preview and it is clear the book has been properly proof read before it was sent for printing.
__________________
Any fool can make things bigger, more complex, and more violent. It takes a touch of a genius, and a lot of courage, to move in the opposite direction. [Albert Einstein]
  Reply With Quote
Old 4th February 2021, 09:42 AM   #5
edbarx is offline edbarx  Europe
diyAudio Member
 
edbarx's Avatar
 
Join Date: May 2018
Location: Maltese Archipelago
Quote:
Originally Posted by nigelwright7557
A transistor doesn't need to be linear as feedback forces it to be linear.
A typical LTP front end just matches output signal to input signal.
Mathematically, for global negative feedback to reduce the difference between the non-inverting and inverting input to zero, the open loop gain must be infinite. Besides, an infinite gain can never be achieved, if such a gain were possible, it would send the amplifier into self oscillation. Self oscillation is why an amplifier employing global negative feedback, has to have its open loop gain reduced, using Miller capacitor compensation, notwithstanding real amplifiers do not have an infinite open loop gain. The capacitor shunts the main audio signal to the VAS's collector, and this shunting becomes more and more pronounced with increasing frequency. So, an amplifier employing global negative feedback behaves differently for all frequencies in the audio range and beyond. At the lowest extreem, negative feedback compensation is most effective because of more open loop gain. However, this effectiveness, decays with increasing frequency, forcing an even bigger voltage difference between the inverting and non-inverting inputs for the same output voltage. This means, the distortion components, that is, the non-linear components that should be added to the distortionless signal to get the voltage difference signal, increase with increasing frequency.

Global negative feedback as used in audio amplifiers is a sword with two edges: it simplifies amplifier design and it introduces problems that would not be present without it.
__________________
Any fool can make things bigger, more complex, and more violent. It takes a touch of a genius, and a lot of courage, to move in the opposite direction. [Albert Einstein]

Last edited by edbarx; 4th February 2021 at 09:46 AM.
  Reply With Quote
Old 4th February 2021, 03:41 PM   #6
Mark Tillotson is offline Mark Tillotson
diyAudio Member
 
Join Date: May 2018
Location: Cambridge UK
Bipolar transistors are fairly linear if used in common-base or emitter-follower configuration though - and not too bad if current-driven in common-emitter. Its only voltage drive that exposes the exponential characteristic, and good amp designs seek to minimize that.

For instance the standard 3-stage BJT amp uses a differential pair, then a current-driven VAS, then emitter-follower output devices.

The differential pair linearizes the characteristic to arctangent, and global feedback then reduces the signal swing over that arctangent region to a very low voltage indeed.

The VAS is linearized at higher frequencies by a capacitor, which also serves to swamp the non-linear capacitance. The capacitor means the global feedback decreases at higher frequencies though, but then there is less VAS distortion for it to cure due to the capacitor.

Basically clever design reduces non-linearities.


There are also some clever front-end designs using the translinear loop principle, where exponentials are used to advantage.
  Reply With Quote
Old 4th February 2021, 05:21 PM   #7
N101N is offline N101N
diyAudio Member
 
Join Date: May 2018
You can`t in any way circumvent the bipolar structure comprising two strongly distortive junction diodes.
  Reply With Quote
Old 4th February 2021, 05:27 PM   #8
stanislav1957 is online now stanislav1957  Russian Federation
diyAudio Member
 
Join Date: Dec 2018
Location: НОВГОРОД
How, then, do they achieve ultra-low distortion on these transistors ?
  Reply With Quote
Old 4th February 2021, 05:28 PM   #9
N101N is offline N101N
diyAudio Member
 
Join Date: May 2018
They don`t.
  Reply With Quote
Old 4th February 2021, 05:36 PM   #10
stanislav1957 is online now stanislav1957  Russian Federation
diyAudio Member
 
Join Date: Dec 2018
Location: НОВГОРОД
Quote:
Originally Posted by N101N View Post
They don`t.
Yes, they seem to reach it.
  Reply With Quote

Reply


What causes BJT based amplifier distortion?Hide this!Advertise here!
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
XLR to RCA adapter causes gross amounts of distortion... shredhead Analog Line Level 13 7th June 2015 02:00 PM
Class D amp distortion causes zigzagflux Class D 20 13th November 2014 12:10 PM
Amp causes speaker distortion blubberboy Solid State 4 11th August 2013 02:49 PM
Determining causes of distortion shzmm Solid State 4 9th February 2010 01:58 AM
What causes distortion? matthias Parts 1 5th June 2004 04:47 AM


New To Site? Need Help?

All times are GMT. The time now is 07:50 PM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.00%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
Copyright ©1999-2021 diyAudio
Wiki