Go Back   Home > Forums > >

Solid State Talk all about solid state amplification.

the (in-) famous mini-Crescendo by elektor
the (in-) famous mini-Crescendo by elektor
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools
Old 27th February 2002, 06:59 PM   #1
Mr. Triatic is offline Mr. Triatic  Sweden
diyAudio Member
Mr. Triatic's Avatar
Join Date: Feb 2002
Location: SWE EU
Default the (in-) famous mini-Crescendo by elektor

i'm about to begin my mini-crescendo project, i have all the parts needed.
The big question is, are there any 'must-do' modifications to the original, to improve stability, to get rid of oscillation, ripple rejection, and so on...

-any suggestions to what kind of volumecontrol/drivestage/inputselector i should use?

-any comments or help greatly appreciated!
  Reply With Quote
Old 27th February 2002, 07:52 PM   #2
wuffwaff is offline wuffwaff  Netherlands
diyAudio Member
wuffwaff's Avatar
Join Date: Aug 2001
Location: Ingolstadt Germany
Hi Triatic,

I donīt know if you already have a pcb but if not try to use 2pairs of Fets per channel. The 7A max current with just one isnīt very much. Get rid of the coupling cap in the feedback and use a dc-servo with an OP77 (described in a few other elektor projects).

Donīt use wirewound source resistors cause this will def. lead to oscillation. Use MJE340/350 as drivers. These can be used in place of the BF469/470 without changes and do sound a lot better. ( BD139/140 are a second choise if the first is not available)

Try to change the input filter to something like 100-160kHz (-3dB).

If you want to do more use a regulated supply for the driver section (LT137AT/LT337AT) at about 3-4 volt above main supply level.

if possible use a double mono configuration for the (unregulated) power supply.

Iīve removed the output inductance in all of the crescendos Iīve build without any problems, you can use 33 and 330pF ceramic caps for the 2SK135 (33 between D and G, 330 between G and S)

  Reply With Quote
Old 28th February 2002, 03:56 AM   #3
diyman is offline diyman
diyAudio Member
Join Date: Nov 2001
Location: Malaysia
Default Crescendo

Hi Triatic

Since Wuffwaff suggested you to try 2 pairs of Fets, you might as well look at the Crescendo, which is the "big brother" giving about 150W if I'm not mistaken. The circuit, if I remember correctly is "similar" with different component values, that's all. Just solder in the component values of the bigger unit into the Mini Crescendo layout and you'll have a mini version of the big Crescendo.
I have built both and the big brother sounds definitely better. As Wuffwaff had pointed out, you'll be very much better off with the dc servo. It opens up the sound whereas the vocals in the original arrangement can sound somewhat compressed at times. Please remember the voltage ratings of the caps need to be much higher if you build the bigger version.
If oscillation happens(which some of my friends experienced!), the DC offset will wander and the 10R resistor in the Zobel network becomes really hot!

  Reply With Quote
Old 28th February 2002, 08:20 AM   #4
Samuel Jayaraj is offline Samuel Jayaraj  India
diyAudio Member
Join Date: May 2001
Location: Bangalore, India
I have built both the Crescendo and Mini-Crescendo with output Mosfets being 2SK1058 and 2SJ162. I designed my own boards, eliminating wirewound Source resistors and replacing these with paralleled 1ohm 1watt resistors. I had oscillation problems with the big brother. The input section was powered separately through a regulated supply - 4 volts higher than the output section. I moved the Zobel network after the 'output choke' rather than the more usual 'before' the choke configuration. This move alone stopped the oscillations. However, I further added caps as already stated by 'wuffwaff' just to be doubly sure. The sound quality is good but not upto the standard of more modern designs.
  Reply With Quote
Old 28th February 2002, 08:28 AM   #5
wuffwaff is offline wuffwaff  Netherlands
diyAudio Member
wuffwaff's Avatar
Join Date: Aug 2001
Location: Ingolstadt Germany
Hi Diyman,

when building the big brother (70-75V supply) maybe 3 or better 4 paralled fets would do. For my self I build one with 3 paralled fets and the supply voltage of the mini crescendo. This gives about 80W/8Ohm and almost double into 4 Ohms and again into 2 Ohms (with 2x 500VA power supply).

With the lower voltage power supply (42V) you can use BC550/560 in the driver stage (instead of 546/556) and the choice of caps for your power supply is a lot easier.

Since I donīt need the extra power (I measured about 240W/8Ohm with 3 paralleled fets and 75V) Iīm very happy with this configuration.
It drives my pair of thiel cs6 without any problems.

  Reply With Quote
Old 21st April 2016, 08:57 PM   #6
eaglemaster is offline eaglemaster  Germany
diyAudio Member
Join Date: Sep 2012
Default I might be a little late!

Originally Posted by Samuel Jayaraj View Post
I have built both the Crescendo and Mini-Crescendo with output Mosfets being 2SK1058 and 2SJ162.
Hello all!
I know this post is ages back and I should use PM, but this didn't work.
I tried to get Samuel Jayaraj without success. So if you read this here, pls PM me maybe u have an email address then available, because I can't PM you.It's about mini-crescendo!

Thank you in advance!
  Reply to this post


the (in-) famous mini-Crescendo by elektorHide this!Advertise here!
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Update for Elektor Crescendo Power Amplifier 1982 bjornagain Elektor 202 2nd April 2021 09:01 AM
Elektor Crescendo from cadsoft.de haseeb Elektor 2 29th September 2011 12:27 AM
Elektor Crescendo Millenium umdem Solid State 4 17th May 2011 02:43 PM
Elektor Crescendo original Knaster Solid State 7 18th July 2005 10:49 PM
Elektor crescendo ME vs ESP project101 supernet Solid State 25 20th March 2005 07:41 AM

New To Site? Need Help?

All times are GMT. The time now is 08:52 AM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 16.67%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
Copyright ©1999-2021 diyAudio