100W Ultimate Fidelity Amplifier

[apexaudio]

Guys let me know if you found any error.

Regards,

Nice work, track mising and wrong pins order on BC547 ( C-B-E instead E-C-B )
Regards

 

[wiljj78]

Nice work, track mising and wrong pins order on BC547 ( C-B-E instead E-C-B )
Regards

Thanks Mr. Mile, it's now corrected.

Regards,

 

[apexaudio]

Thanks Mr. Mile, it's now corrected.

Regards,

Thank You for this PCB design.
Regards

 

[wiljj78]

Thank You for this PCB design.
Regards

Welcome..... Here's the file.

Regards,

 

[wiljj78]

Greetings mister whether these protectors can also be used to ax 17

thank you

Let's hear the answer from Mr. Mile about this question.

Regards,

 

[Vostro]

Lets get confirmation from Mile, but this protection should be generic for any amplifier.
Some component values might need to change,

This protect is a great share.
Thanks Mile

Regards

 

[apexaudio]

This PSU with protect can be use for any amplifier, just change 680R/2W resistor to get 24V on relay or 12V for lower rail voltage and 12V reley.

 

[wendipassundan]

ax 11 desain

This PSU with protect can be use for any amplifier, just change 680R/2W resistor to get 24V on relay or 12V for lower rail voltage and 12V reley.

thank you sir Mile who have shared her design and host wiljj78 very helpful for people like me who want to make the power amp


greetings, arif sumadireja

 

[apexaudio]

This simple shunt regulator can be use with AX amplifiers for preamp supply. Amp rail voltage can be use for regulator input (without 1N4007 diodes and 4700uF caps).

 

[wiljj78]

This simple shunt regulator can be use with AX amplifiers for preamp supply. Amp rail voltage can be use for regulator input (without 1N4007 diodes and 4700uF caps).

Here's the PCB.

Regards,

 

[44250]

great job!

Here's the PCB.

Regards,

great job!

i have tried to do it too but not even near as good as you did it

 

[apexaudio]

Here's the PCB.

Regards,

Very nice PCB design, thank you.

Regards

 

[wendipassundan]

bottom layout

Here's the PCB.

Regards,

Her design is very nice, is there a bottom layout ..

Thank you so much ..


regards ,arif

 

[wiljj78]

Thank's

Here's the buttom layout.

Regards,

 

[DAMANHURI]

Thanks Sir Wiljj78, my question : how the size of the image?
Regards,

 

[davidus]

Thanks Sir Wiljj78, my question : how the size of the image?
Regards,

PCB size: 57 x 72 mm

 

[44250]

it is written at pictures in previous page.

 

[borys]

I've played a bit. A small heatsink connected with thermal adhesive (more for peace of mind;-). Some photos for 20kHz, 10kHz and 1 kHz with signal generator until 30V peak to peak at output. Load resistance and heatsink are good warm (too small).
In each perspective the amplifier operates stable and has a warm and transparent sound.
It is a very nice, cool amplifier - typical apex.
It's fun to build it and you get an impressive sound.

Thanks again to Apex.
regards

I do not know if I am asking for too much but can You repeat one square wave measurement on 8 r with small cap in parallel please ( someting like 0,47uf or similar)

Thanks

 

[olafk]

Yes, no problem, but not before next week - because i am not at home this weekend.

Regards

 

[apexaudio]

Here's the buttom layout.

Regards,

Thanks I'm gone to use it.
Regards