Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Solid State Talk all about solid state amplification.

Marantz SR5300 Receiver Problems
Marantz SR5300 Receiver Problems
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 15th July 2007, 11:16 AM   #1
Thomo is offline Thomo  United Kingdom
diyAudio Member
Thomo's Avatar
Join Date: Nov 2006
Default Marantz SR5300 Receiver Problems

I have a Marantz SR5300 Home Cinema amp which has a problem. When I switch on, the power led lights up, but that is it. No relay click, no display, nothing.

I am just wondering if anyone has any knowledge of common faults with these units, or has any ideas of how to find the fault.

I have removed all of the boards at the rear of the unit from the "motherboard" one at a time and still nothing happened so I don't think the fault is with any of those.

I am quite stuck as to where to start looking.

Regards, Lee.
  Reply With Quote
Old 15th July 2007, 11:35 AM   #2
Burnedfingers is offline Burnedfingers  United States
Account disabled at member's request
Join Date: Nov 2002
Are you hearing the speaker relay click in? If your not there could be a malfunction that will probably end up being excessive DC on the output of the amplifiers. The protection circuit monitors the amplifier output and latches up the speaker relay when everything is ok. There could also be a problem with the preamp section of the unit. I have seen this result in a no display condition.

The company I work for sells Marantz as a product and they haven't had a real good track record. If you aren't skilled in the field I would send it to a Marantz repair station. If it has taken a hit as a result of a storm I would head to the nearest dumpster and deposit it.
  Reply With Quote
Old 15th July 2007, 04:02 PM   #3
Thomo is offline Thomo  United Kingdom
diyAudio Member
Thomo's Avatar
Join Date: Nov 2006
Hi again. I think I have narrowed it down a little.

I have removed all of the plug-in boards from the mainboard. I have disconnected the board with the output transistors.

If I disconnect the main power feed from the mainboard and power on, the display works, registers volume and selects sources so I don't think the preamp / control section is faulty.

With the main supply reconnected I read -50v across one res. cap but 0v across the other. If I then press a source select button the display flickers and relays click and the non-charged cap charges to +50v. That cap then discharges very, very quickly making it impossible to check voltages in the circuit. The other cap, negative supply stays charged for ages.

Any ideas anyone?

Regards, Lee.
  Reply With Quote


Marantz SR5300 Receiver ProblemsHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
problems with a Setton RS-660 receiver theblackknight Solid State 7 22nd December 2008 01:37 PM
CS8414 receiver problems Skorpio Digital Source 9 29th October 2007 12:25 PM
marantz receiver odysseybmx414 Solid State 12 30th December 2006 08:36 PM
Marantz receiver repair SoundQuest Parts 0 4th June 2004 05:24 AM

New To Site? Need Help?

All times are GMT. The time now is 07:25 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.79%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio