diyAudio

diyAudio (https://www.diyaudio.com/forums/index.php)
-   Tubes / Valves (https://www.diyaudio.com/forums/tubes-valves/)
-   -   First shot at a battery DHT preamp stage (https://www.diyaudio.com/forums/tubes-valves/344733-shot-battery-dht-preamp-stage.html)

mondogenerator 2nd November 2019 02:30 PM

First shot at a battery DHT preamp stage
 
3 Attachment(s)
Hi!

I've had a few of those cheap Soviet battery valves sat around for a while (1J29B and 1P24B)

I'm a relative novice in valve circuit design, but I've studied a few schematics on the www, and come up with a couple of 'first shot' ideas. Dont expect perfection, I've only ever made simple stages using 3 or 4 variety of valves, and a simple output stage.

I plan to build and test these ideas, and optimise them (provided they work at all)

My planned applications are probably instrument based effects, but whilst a harmonic generator may be useful, I also plan on making an iteration as clean as possible, so I will also be making effort to reduce THD, as well as create musical THD.

Something about DHTs seem to make circuits more difficult to design (perhaps that's all in my head)

I have drawn a couple of basic designs for using 1J29B in pentode mode, B+ 60V Vg2 45V; and also a triode wired operating on 45 to 60V. For the time being these will be powered using multiple PP3 batteries.

I would be grateful if some of the more seasoned designers could look over the schematics, simple as they are, and offer some practical critique/advice.

PRR 3rd November 2019 05:12 PM

The filament battery is important for correct bias. You want the middle of the heater to be positive relative to grid to get correct negative bias. The way your filament battery is drawn look wrong to me.

I have not looked-up your tube but 22k seems an awful heavy load for a very small thin tube. You won't get a lot of signal voltage before distortion. Maybe that's "good"?

But what is your question?? You say the tubes are cheap. TRY THEM! You'll learn more in a couple sessions than forum-yack can ever tell you. Don't get the filament across a fat B battery (not a problem for the old 67V batts which would just sag, but you are probably using wall-plug supplies). Be sure there is many-K resistance in series with the plate so it can't try to suck infinite current.

jhstewart9 3rd November 2019 07:33 PM

These toobs look like something designed for a proximity fuse. That might be a good sign indicating better microphonics. And perhaps no!:)

PRR 3rd November 2019 07:40 PM

> designed for a proximity fuse.

While tube is tube, these seem aimed at battery radio. If well done, the filaments run HOT for better battery economy at the cost of shorter tube life. (In hearing aids, battery cost was 10X tube replacement cost over the life of the aid.)

piano3 3rd November 2019 09:45 PM

I built a mic amp with 1j24b which is similar to 1j29b but with even lower heater power. They were happiest with 90-100 volts on the anode and a couple of milliamps. I think I biased them with several 1N4148 and a current source. The filament was powered by a D cell and a dropping resistor. They were utterly non-microphonic and the sound was very clean but I didn't keep it as the hiss was a bit high for purpose (this could possibly have been oscillation, although I did take the usual precautions). I also wondered if the hiss was a consequence of the very low heater power.

Edit: They were triode wired.

Hearinspace 3rd November 2019 10:05 PM

You might also enjoy a look at member Thomasha's work with these tubes. He did a very cool lithium ion battery powered guitar amp. Thread is here and link to his YouTube vid of it is in post #61. More helpful stuff from PRR there as well.

mondogenerator 3rd November 2019 10:22 PM

Hi,

Firstly,

PRR, the anode load much more than an arbitrary value that I inserted for the sake of having a number.

Maximum cathode current is 5 to 8mA at most, so 22k is the absolute minimum. More likely it would be double or more, say 47k to 100k.

The exercise of drawing a crude schematic is more to form up the idea in my head. Admittedly DH are more difficult for me to get my noggin around.

Regarding the filament, design voltage is 1.2V in parallel connection, centre tap being the earthy end. So I'll probably use a alkaline cell, with resistor to drop 0.3V.

After posting in haste, I did consider that I would probably need a cathode resistor, which I hadn't thought through (still havent...) - cathode bypass isnt something I have thought about just yet either.

The 1J24B, if I recall, is lower dissipation than 1J29B, although I'll add the remark that there is conflicting information online, incorrect links and tube codes, even on Radiomuseum.

However, these are cheap. I have 10 and they're probably about 1 each or less by the time shipping costs included.
1J29B are from what I read useful for 500mW front end AF

1P24B, the "power" tubes, are more costly but I have a few of those too! The history behind them (Sputnik) is fascinating.

They certainly arent proximity fuse types, judging by the information online, though some of this type certainly were (1J17B?)

I have also seen the headphone amp schematics using variants of these rod pentodes, and in might just build one of those in time. The biggest problem with that is my 300R Sennheiser is not the intended 600R load!

HearinSpace,

Indeed I have read Thomasha thread, viewed his videos, some months ago, and that lead me to try and find out more. It certainly helped me get a feel for what is possible if I utilise more than 1% of my brain!
His mini amp, even sounded pretty good - not amazing, but hell, I'd be chuffed to bits with it if I designed it. But it kind of drops off the edge of a cliff, as so many threads do.

So, ok...a couple of mA anode current. I can do that.
90V is pretty much datasheet max anode volts.
Diode or LED bias is definitely something I'll try with these, maybe a CRD diode at 1-2mA.

Thanks, really helpful stuff!

PRR 4th November 2019 02:53 AM

> I would probably need a cathode resistor

No. This is awkward when you do not have insulated heater-cathode tubes. These tubes are normally biased with a combination of a large (5Meg) grid resistor, and the ~~ Volt drop across the heater (grid tied to one end, +1V at the other end, the "average" grid bias is -0.5V, which with grid-R drop is often enough).

Plagiarize plagiarize plagiarize!!! Study all the beach-radio schematics you can find.

disco 4th November 2019 08:21 AM

Heaters are 100mA? Just stick a 330R in one filament leg, put the other to ground and run 'm from a 12V supply. For ultra low noise I would drop 50V -> 12V.

mondogenerator 4th November 2019 12:08 PM

Disco, you've lost me a bit there.

Yes, heaters in || are about 100mA. (50mA each)

Dropping 0.3V from 1.5V cell, by my simple reckoning, requires 0.3/0.1 = 3R stopping resistor. 3R3

12V supply at 100mA, needs about 0.1A*11V drop, 110R resistor. Probably 120R nearest value.

Unless I am missing something (quite possible)


All times are GMT. The time now is 03:55 AM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 17.65%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Copyright ©1999-2020 diyAudio

Wiki