Hybrid with Nelson topology
We all know Nelson Pass patented output topology, the so-called active current source.
It works wonderfully, I've already built few Pass clones (prototypes, actually) and every one is amazing.
I have to add I also love tubes; so, why not to add Nelson art with some tube "signature"?
My idea has been to "invert the output topology, and realize a voltage follower, driven by a tube input stage:
As you can see the active curernt source has been moved in the lower part of the output stage, but its behaviour should be the same.
The upper mosfet works as a voltage follower; the DC operating point is controlled by the OP07 chip, while the audio signal comes from the tube long tail pair in the input.
I have not yet made any calculation, so I do not know if the circuit works in the current version and if the components values are accurate.
I even don't know if the choosen tubes (the only one I have) have enough gain to drive the output stage to full power.
I show you the schematic just to know if this could become a working amp.
But the aleph output stage usually have quite a lot of gain, so you will be in trouble if you wire it as a follower. If you want n type frontend, the standard way to go is to use p type output fets.
in any way ......... double dutchie ........ (speaking about jaccovity ;) )
with follower config - input tube must fight with input capacitance of big IRF
with standard Aleph config ( output stage with gain ) problem is that output mosfet's input is referenced to PSU's plus ....... and having same
pSU rail for both tube and mosfet is tricky ......... and having different rails ...... even more
tube input stage , with dedicated PSU + rail ....... neat cascoded current mirror/voltage shifter stage ...... regular Aleph output stage .....
but - is it worth ?
no , at least to my xperience .
jfets on input are exactly adequate tubes :rofl: for Aleph .
it's wise to save tubes for roles where sissy jfets are ..... sissy .
as always ..... YMMustV
Even simpler: THIS version uses only one triode; I'm not sure if the feedback can actually work this way, never seen before.
I know the source could have some problem driving the input stage, but I don't think my CD should.
If you invert the position of the two mosfet in the Nelson topology, the output stage gain will drop below 1, according to the source follower phisics.
The important thing is to DC bias the gate, thing done with the OP07.
Theoretically the input impedance of a voltage follower/source follower/common drain stage is infinite:
Even more, I know I will have to add some timed relay to realize a precise startup sequence:
1. Power the input stage filament
2. Power the output stage, and wait until the OP07 DC bias it.
3. Power the input stage and wait
4. Connect the output to the loudspeakers
And if it can be done, let's do it! :D
And, moreover, I LOOOOVE tubes, so why not to put them in a so sweet amp?
I'm looking at the current sink in the upper right corner.
Honestly, I don't think anything but your mosfet is active.
Below the set limit, the transistor might as well not even
Yes, if the current draw tries to rise above the "constant
current" limit it shunts gate to the output. I'm not sure
what ever pulls the gate back up again? I see no pullup
circuitry. And the cap C4 can't conduct DC...
Perhaps you are relying on the opamp to recharge C4
on the opposing downswing? Or maybe I don't get it...
You don't need all that useless current regulating crud
on Q7, as it seems to me that Q7's job is enforcing the
output voltage as a pure follower. And Q8's to set the
quiescent DC current, and perhaps swing an opposing
AC current in Aleph style paraphase.
I simply cut'd and paste my previous schematic from Aleph Mini...
The current limitng circuit on top is useless.
THIS should be correct.
The input is the second variation.
Stephen Moore did a ZEN based hybrid in aXp. I think the Akido on the front-end could be replaced (to good effect) with something simplier, but he does some intersting things with the ZEN.
Bbootstrap in that schematic may not be connected optimally.
He's got his music output shunted thru resistor R7 to PSU+.
Referring to moore2355, I havn't gotten to the other yet.
If he'd tied the lower end of cap C3 to Q2's source, any
bootstrap and PSU noise would remain hidden above &
behind the Aleph regulated current as seen thru R5...
And that article has to be the third time today I've read
some nonsense how a follower hides gate capacitance.
Its starting to become my pet peeve.
Granted, it doesn't multiply it by swinging an opposing
signal. But you still have to charge or discharge a gate,
or nothing of interest happens in the channel.
Simple case of cause before effect.
Love the doggy thing...
|All times are GMT. The time now is 07:12 AM.|
Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 17.65%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio