Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

what's a good power supply?
what's a good power supply?
what's a good power supply? Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 18th November 2019, 09:30 AM   #1
myleftear is offline myleftear  Switzerland
diyAudio Member
 
myleftear's Avatar
 
Join Date: Sep 2017
Location: Luzern
what's a good power supply?
Default what's a good power supply?

Hello everybody

Being fascinated of all diy and audio, I try hard to follow all these very elaborated conversations. Problem is, I haven't the experience to understand it.

I built my ACAmp and am very happy with it, but—of course—want the project to continue, mind you

Next steps are to build another one or two and run them bridged/parallel, and to tweak it as suggested here and there. Many are saying that a great improvement can be made with the use of a good PSU...

But, what exactly IS a good one? How do I identify a good (or not so good) without spending money on it and trying it out (that is, by reading the specs and stuff)?

You know, is this (MeanWell 24V150W) good enough, or that (another one) , or should it be some shiny high end mega-beast like that?

Oh, and don't worry, I'm being cautious, and won't burn down the house. I'm just reading (yet).

Thanks very much!
__________________
dobedobedo...
  Reply With Quote
Old 18th November 2019, 10:01 AM   #2
ubergeeknz is online now ubergeeknz  New Zealand
diyAudio Member
 
Join Date: Aug 2018
I believe a good power supply:

1. Has the required voltage output for the application

2. Can provide all required current for the application

3. Has a low impedance within the operating range (that is, the voltage stays much the same regardless of current drawn)

4. Injects minimum ripple and noise

Ideally, a power supply would have the exact voltage you want, zero impedance, an infinite current capability, zero ripple, and no noise.

But of course these things are impossible so it becomes a balancing act between cost and meeting or exceeding the required performance parameters.
  Reply With Quote
Old 18th November 2019, 10:49 AM   #3
FauxFrench is offline FauxFrench  France
diyAudio Member
 
Join Date: Dec 2017
Location: The mountains, calm and quiet.
To the above good list I will add from practice and for audio amplifier use a regulator with "fast load response". Fast load response means the ability very fast to establish the nominal voltage when the loading is changed. When the load current is suddenly increased or decreased, the regulator circuit will have to adapt the output current to the new loading in order to return to the nominal voltage. Some regulation loops react fast, some much slower. The need for fast reaction heavily depends on the speed at which the load changes and also the design of the power stage. Audio power amplifiers (except pure class A) are very fast changing loads that may make an else low noise power supply change heavily in output voltage due to constant changes of the load current. Changes in output voltage influence amplifier distortion and thus sound quality.
While most other parameters are specified in the power supply specification sheet, load response is more rarely addressed.

A current limiter may be a very useful feature, in particular for a laboratory supply. The current limiter serves to protect the power supply and often also the load from destruction.
  Reply With Quote
Old 18th November 2019, 12:01 PM   #4
amplidude is offline amplidude  Denmark
diyAudio Member
 
Join Date: Feb 2016
I tend to oversize my amp psu, a good psu is essential for good performance, don't save on money that.
The list above is good answer
  Reply With Quote
Old 18th November 2019, 06:43 PM   #5
Mark Tillotson is offline Mark Tillotson
diyAudio Member
 
Join Date: May 2018
Location: Cambridge UK
Good (class A/B/AB) amps generally have good PSRR and place little demand on the power supply other than they supply the power demanded (ie the first three bullet points of post #2).
Lower quality amps place greater demands on the PSU to compensate for poor PSRR.

Class D can be another matter, some demand very quiet supply rails, others compensate for variations in supply voltage to various extents.

Basically high PSRR in the amp, simple supply will work well, poor PSRR in the amp, PSU has to nurse the amp into performing.

Switch-mode PSU's can be an issue with high frequency noise they generate intermodulating in an amp. Probably no simple rules of thumb here.
  Reply With Quote

Reply


what's a good power supply?Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
A good power supply for the LDR attenuator? max1979 Power Supplies 3 15th September 2015 08:43 PM
Is this switching power supply any good - srinath Power Supplies 7 8th October 2014 07:49 PM
Good Power Supply?? denny9167 Tubes / Valves 12 25th December 2013 02:26 AM
BOZ power supply - is it good enough? beppe61 Pass Labs 3 26th May 2005 08:19 AM
What makes a good power supply? Calimero Solid State 7 28th August 2003 10:52 AM


New To Site? Need Help?

All times are GMT. The time now is 05:39 AM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.00%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Copyright ©1999-2020 diyAudio
Wiki