Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

PA Systems A forum for discussion of all parts of a sound reinforcement or DJ system: loudspeakers, mixers (desks) etc.

L2 WMP12 300watt active floor monitor
L2 WMP12 300watt active floor monitor
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 10th March 2020, 02:18 PM   #1
blockhead65 is offline blockhead65  United Kingdom
diyAudio Member
 
Join Date: Dec 2018
Location: Hampshire
Default L2 WMP12 300watt active floor monitor

Good afternoon to you
Now I might be being a dick here. But this amp is causing me pain
I'm not an electronics engineer by trade, I have some knowledge
and now do this for fun, But i'm like a dog with a bone, won't let go

It came in to me with a intermittent noise issue.
I found the fault IR9 was soldered in but leg cut short it wasn't really soldered. Replaced it.
Out the job went ok
1 month later it came back distortion after a while.
I found by heating and freezing the area around IQ5 it would go away. In the end I replaced all the transistors in that area IQ1 to 7 and 14. As all very close together.
All changed like for like.
Tested the amp heat and freezer it all seemed OK.

Then it went to about 1/2 volume without touching it I wasn't heating or freezing at that time was on for 20 mins before it went
When I tested it I can see its working perfectly without distortion but low output
PM12-AMP.pdf
On checking using scope and signal gen I can see the signal in and out of pre amp is OK and higher level leaving the pre amp than the input.
I'm I being a dick question
But the signal entering the power amp is at same level as the output.!!!!
Is this possible?
Check all voltages 54v +/- and 15v +/-
Checked all the transistor /diodes
Made sure the transistors I changed are good and correct ones
At output have around 3v ac with gain /vol max
I'm not an experienced tech. Just play for fun
Any assistance would be grateful thanks in advance

Blockhead
  Reply With Quote

Reply


L2 WMP12 300watt active floor monitorHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Small active 3-way floor stander with a punch DannerD3H Multi-Way 167 25th January 2020 11:06 AM
Active, 3-way monitor project studiotech Multi-Way 13 9th July 2014 01:11 AM
Initial thoughts - 3-Way active floor stander as first project... bushmeister Multi-Way 29 14th February 2013 01:41 AM
op-amp with filter for active monitor? jayless Chip Amps 1 17th March 2010 11:55 PM
Help me build an active monitor for dj'ing lunchmoney Multi-Way 14 6th April 2005 01:50 AM


New To Site? Need Help?

All times are GMT. The time now is 12:06 PM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.00%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Copyright ©1999-2020 diyAudio
Wiki