Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Multi-Way Conventional loudspeakers with crossovers

12" & Horn 2-way build
12" & Horn 2-way build
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 4th January 2020, 03:15 AM   #1
benno25 is offline benno25  Australia
diyAudio Member
 
Join Date: May 2006
Default 12" & Horn 2-way build

Hi all,

I have some RCF HF94 90x40 horns which I'd like to use for a 2-way active speaker build. I'll be building 3 speakers (left, centre, right) for home theater.
Goal is for something which can play loud effortlessly with plenty of dynamic range. The will also be used for music and need to stand up to the occasional party when the volume gets turned up also!

Anyway, I'm currently seeking any tips or suggestions for a 12" woofer and 1-1.4" inch compression driver that would work in this scenario. Budget caters for higher end components if worthwhile (without going super expensive though).
What do people recommend?

As for compression drivers, the B&C DE250 seems to get good reviews. Would this be suitable and be able to crossover low enough, or should I perhaps aim for something different or a 1.4" driver?

As for woofers, I'm looking at a pro audio driver to meet the output needs.

Finally, is it worth considering using a sealed enclosure for the woofer to better integrate with subs?

Thanks for your help.
Benno
  Reply With Quote
Old 4th January 2020, 01:26 PM   #2
kipman725 is offline kipman725  United Kingdom
diyAudio Member
 
kipman725's Avatar
 
Join Date: Jun 2007
Location: Warrington
Send a message via MSN to kipman725
The horn and woofer are going to be bout 300 mm minimum C2C spacing, this results in 1/4 wavelength been at 1147 Hz, ideally you want to crossover below this frequency to avoid irregular polar response in the vertical plane. For this low frequency you will want a driver with a larger diaphragm than the typical 1.75" dome found in 1" compression drivers, so I would tend towards 1.4" throat drivers. The sacrifice with larger throat drivers is sometimes the high frequency dispersion is constrained by the throat size. Saying that there are so many cravats on that actually happening (for example):
1. Plane wave condition at the throat, if the wavefront is bent into a circular cap the narrowing is at a higher frequency.
2. No diffraction
In your case the HF94 has a diffraction slot for the wider horizontal plane so I can see no disadvantage apart from cost to go with the larger throat. Another advantage of larger throat and diaphragm drivers is that the distortion in a compression driver is mainly due to air non linearity and so as they have a greater spacial volume they typically have lower THD at a given SPL. However larger diaphragm drivers can also have more problems with the dome breaking up, particularly Ti diaphragms due to the lack of damping, so I would recommend choosing a driver using a polymer diaphragm. Be diaphragms avoid breaking up in the audible band even for a 4" diaphragm but are not in the non super expensive category:

This Faital pro driver looks great, capable of very low crossover and smooth frequency response curve indicating well controlled breakup behaviour. Not sure if its actually available yet?
HF1440

There is also the DCX464 coaxial compression drive.
  Reply With Quote
Old 5th January 2020, 01:47 AM   #3
LineSource is offline LineSource  United States
diyAudio Member
 
LineSource's Avatar
 
Join Date: Sep 2003
Location: SiliconValley
The B&C DE250 is a very good 1" compression driver.... smooth.... capable of 1.2 - 1.3kHz crossover.
=============
A few 12" midbass capable of smooth 1.1 - 1.3kHz crossover to 1" horn.
--Dayton paper Dayton 12" woofer DS315P-8 $80
--Eminence DeltaPro 12A $130
--Eminence Kappalite 3012HO $190
--Faital 12PR320 $230 (I have and like the Failtal 12PR300)
=============
A properly designed sealed 12" cabinet will produce better transients than a ported alignment, BUT sealed has a higher -F3 frequency so woofer selection and placement is more important. A single cabinet 3-way may be more difficult to design, but it both limits the scope of the challenge and forces the designer to create a complete CAD before spending money and cutting wood. Your center channel can still be a 1" CD + horn + sealed 12" midbass.

Mark Levinson has made BIG & TALL attractive with his Daniel Hertz M1 speaker. 1" horn + 12" midbass + 18" woofer

The Tweek Geek audio Boutique in Colorado uses a pair of counter-force 12" woofers to match the area one 18" woofer.
Attached Images
File Type: jpg Daniel Hertz M1 1x12x18.jpg (162.9 KB, 629 views)
File Type: jpg BMF-12x12.jpg (175.7 KB, 638 views)
File Type: jpg tall 1x12x18.jpg (160.5 KB, 634 views)
  Reply With Quote
Old 5th January 2020, 08:37 PM   #4
kipman725 is offline kipman725  United Kingdom
diyAudio Member
 
kipman725's Avatar
 
Join Date: Jun 2007
Location: Warrington
Send a message via MSN to kipman725
As this is got HT I would omit those 18" drivers as the frequency range <80 Hz should be taken over by your subs. Bass reflex is very useful to control cone excursion when used with appropriate high pass filtering and aids driver cooling if operating at sustained high power (by selection of a high tuning frequency). Reducing cone excursion reduces the modulation of higher frequencies the midwoofer has to produce and reduces harmonic distortion so increases fidelity.

For me the downside to ported boxes are the inevitable pipe pipe modes and mid-range leakage. This can be reduced by careful application of damping material and keeping ports short such that any problems are pushed up in frequency where the damping is effective.

Here is the kind of performance a 12" high end pro driver can get:
Test Bench: The PD.124NR1 High Power 12” Neodymium Midbass Driver from Precision Devices | audioXpress
You can observe that its above 120dB/1m down to 70 Hz which should be enough unless your home theatre is huge.
  Reply With Quote
Old 6th January 2020, 08:11 AM   #5
LineSource is offline LineSource  United States
diyAudio Member
 
LineSource's Avatar
 
Join Date: Sep 2003
Location: SiliconValley
Quote:
Originally Posted by benno25 View Post
Goal is for something which can play loud effortlessly with plenty of dynamic range. They will also be used for music and need to stand up to the occasional party when the volume gets turned up also!
Geddes: “The mains should be designed for the best possible direct field with as flat a power response as possible. Room bass equalization using the mains could only make them worse.” Initially put your single subwoofer along the rear wall to help equalize room bass modes at the listener.
=====

There are benefits to building a pair of high quality 3-ways with -F3 ~30Hz to generate an optimal stereo soundstage.

1) Stereo bass down to 20Hz has been produced in low distortion, high SPL since 1982 on CDs, DVD-As, SACDs, and 5.1 movies.
2) Most people with normal hearing can identify the difference between stereo vs. mono bass. Stereo bass has phase for location.
3) At frequencies below 80Hz most people with normal hearing cannot isolate the physical location of the woofer.
-----Expert listeners can isolate location of woofers down to 60Hz by focusing on impact harmonics, port noise, upper harmonic distortion.
4) Not being able to locate the subwoofer is a good cost simplification, but summing low bass into mono degrades true stereo recordings.
5) With stereo woofers & subwoofers, any out-of-phase bass information in a true stereo (acoustic) recording is reproduced properly at full level, adding immensely to the perceived width and depth of the room in which the recording was made.
=====
Attached Images
File Type: jpg Stackable 12 x 18.jpg (111.3 KB, 522 views)
  Reply With Quote
Old 6th January 2020, 08:29 AM   #6
benno25 is offline benno25  Australia
diyAudio Member
 
Join Date: May 2006
Thanks for the input guys, much appreciated.

Based on comments and research so far, I'm leaning towards a 1.4" compression driver, as I feel this will give me more flexibility with crossover points and allow it to go lower if required. The Faital HF1440 sounds like a good choice (if available). Are there any other 1.4" drivers that get good reviews people would recommend?

As for woofers, I'm pretty sure I'll aim for a ported configuration.
As mentioned I'll have subs to fill in the <80Hz region so getting deep bass extension isn't a big priority. I consider it more of a nice to have if possible.

Kipman, I'm interested in your comment regarding pipe modes, mid-range leakage and keeping ports short. How short would you consider short?
I've been playing around with B&C 12NDL88 woofer numbers in WinISD where 2x 4" ports seem to be over 20cm in length for the manufacturer recommended box volume (40L) and tuning frequency (65Hz). Should I aim for smaller diameter ports to reduce their length, as any port chuffing is likely inaudible at high SPL's anyway?

I've also played around with the Faital 12PR320 numbers in WinISD which appears to have a little more bass extension than the B&C. Additionally it seems to extend higher in frequency also, so I'm thinking it may be a good choice and provide some added flexibility in the crossover again if required?
Are there any other popular driver people use with good results which are recommended?

Finally, from my understanding all 12" woofers seem to suffer off axis response (beaming) once they start getting up over 1-1.5kHz, so I'm running under the assumption if my target crossover frequency is around 1kHz or less, I should be fairly safe with it integrating with the horn ok? Assuming the woofer has adequate high frequency extension and doesn't start breaking up or show any irregular behaviour or off-axis response around the 1-2kHz region?
Is this a reasonably safe assumption?

Again, thanks for the comments guys.
I apologize for the noob questions
  Reply With Quote
Old 6th January 2020, 08:41 AM   #7
benno25 is offline benno25  Australia
diyAudio Member
 
Join Date: May 2006
Quote:
Originally Posted by LineSource View Post
Geddes: “The mains should be designed for the best possible direct field with as flat a power response as possible. Room bass equalization using the mains could only make them worse.” Initially put your single subwoofer along the rear wall to help equalize room bass modes at the listener.
=====

There are benefits to building a pair of high quality 3-ways with -F3 ~30Hz to generate an optimal stereo soundstage.

1) Stereo bass down to 20Hz has been produced in low distortion, high SPL since 1982 on CDs, DVD-As, SACDs, and 5.1 movies.
2) Most people with normal hearing can identify the difference between stereo vs. mono bass. Stereo bass has phase for location.
3) At frequencies below 80Hz most people with normal hearing cannot isolate the physical location of the woofer.
-----Expert listeners can isolate location of woofers down to 60Hz by focusing on impact harmonics, port noise, upper harmonic distortion.
4) Not being able to locate the subwoofer is a good cost simplification, but summing low bass into mono degrades true stereo recordings.
5) With stereo woofers & subwoofers, any out-of-phase bass information in a true stereo (acoustic) recording is reproduced properly at full level, adding immensely to the perceived width and depth of the room in which the recording was made.
=====
This is something I'd like to consider or play around with by moving my subs next to or below my left/right speakers and running them stereo in future.
For the time being home theater is the primary goeal and I'm planning to stick with a 2-way setup. My only concern however is whether the 12" drivers being ported will cause issues when integrating with the subs?
  Reply With Quote
Old 6th January 2020, 03:58 PM   #8
kipman725 is offline kipman725  United Kingdom
diyAudio Member
 
kipman725's Avatar
 
Join Date: Jun 2007
Location: Warrington
Send a message via MSN to kipman725
I like to run 4 subs at home that are approximately equi distant to the listening position in the corners of the room as this gives a very even bass throughout the room. My personal preference that I like a surrounded by sound sensation. I am also unsure of how stereo bass is compatible with room equalisation which I consider to be essential. I crossover at 120 Hz (acoustic): I can't localise the bass but I run very large subs far below their maximum output so don't have the higher frequency noise ques other people may have. I think a lot audibility of 'high' sub crossover points may be because its common to set the sub crossover electrically and assume the sub crossover is at that point acoustically. If the sub is louder than the tops then the actual acoustic crossover point is higher in frequency than the electrical. But after all try various things and see if they work, after all its not like there is a standard mastering studio.

If you model your ported box in Hornresp and correctly put in your box dimensions and port lengths you see the undesirable resonances in the frequency response graph, this will be very accurate. Hornresp also predicts vent air velocity which you should keep <17m/s. Here is some data on stuffing subs:
dB v2
Here are the calcuations you need for an open pipe (port):
Acoustic resonance - Wikipedia
I would use a single port just large enough to keep the velocity under 17m/s at maximum output with your intended high pass filter.

Crossover to your horn around 800 Hz (90 degree directivity point of the 12" driver - see audioxpress review above) however I'm not sure the horn able to control directivity this low or if distortion will rapidly increase below this point. Realistically a two way is a bit of a fudge and the crossover point is going to have to be a compromise. Perhaps you could use 48dB/octave slopes? or even steeper FIR? these can have group delay implications though.

*another unusual thing I like to do is have my speakers above sitting height and aim downwards as this produces a larger in room listening window and minimises ceiling bounce. This is a bit tricky if you speaker can't be pole mounted because its got an 18" bass driver.

Last edited by kipman725; 6th January 2020 at 04:04 PM.
  Reply With Quote
Old 6th January 2020, 04:42 PM   #9
kipman725 is offline kipman725  United Kingdom
diyAudio Member
 
kipman725's Avatar
 
Join Date: Jun 2007
Location: Warrington
Send a message via MSN to kipman725
Some driver choice discussion here:
Compression driver to suit RCF HF94 waveguide

The HF95 is a similar (larger?) horn so this data may be useful:
Test Bench: RCF ND950 Neodymium Compression Driver and HF950 Horn | audioXpress
  Reply With Quote
Old 8th January 2020, 12:53 AM   #10
LineSource is offline LineSource  United States
diyAudio Member
 
LineSource's Avatar
 
Join Date: Sep 2003
Location: SiliconValley
Quote:
Originally Posted by benno25 View Post
This is something I'd like to consider or play around with by moving my subs next to or below my left/right speakers and running them stereo in future.

My only concern however is whether the 12" drivers being ported will cause issues when integrating with the subs?
If you plan to put the (sub)woofers below or next to the 12" midrange, a sealed cabinet will give you better transients and still integrate with the adjacent (sub)woofer.

If plan to put the (sub)woofers around the room, the lower frequency bass from ported midrange cabinets typically allows better room integration.
===========
===========
How deep of a speaker cabinet will fit your room / goals?

You want the center of the compression driver at a height of 36" - 39" for ear level. For breathing room around a 12" midrange you want a 15" - 18" wide cabinet.

So, consider building a cabinet of similar size like the Tweek Geek BMF-1 43”high x 16”wide x 20”deep
-OR-
A wider cabinet for larger radius edge cuts to reduce distortion, and less depth might come in about H46" W18" D17" This wider cabinet matches the 14.5" width of the popular PRV WG35 waveguide which I use (now Parts Express B-52 PHRN-1014) .

This will allow you to add a pair of counter-force 12" woofers in the future.
  Reply With Quote

Reply


12&quot; &amp; Horn 2-way buildHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Horn Help: 2" 400-500Hz Horn Justauby Multi-Way 6 12th October 2017 01:46 AM
Horn Build using a tapped horn as a frame?? 3GGG Multi-Way 1 18th January 2012 12:52 AM
12" full range on a backloaded horn, BIB, tappered quarter wave or other horn boxes? c3conv Full Range 1 27th July 2011 06:37 PM
Need opinions for 10" pro woofer + horn build dabbler Multi-Way 74 1st October 2010 11:46 AM
Grill Material for Stan White &quot;Curled&quot; Horn Reproduction rlabomb Multi-Way 0 26th May 2008 03:24 PM


New To Site? Need Help?

All times are GMT. The time now is 06:39 AM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 14.29%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Copyright ©1999-2020 diyAudio
Wiki