Coaxial Speaker Build Thread with FaitalPro 6HX150

Ok time for a new build thread!

I’ve been planning my InDIYana event “Keeping up with the Jonzes” build for some time and am finally getting splinters from it!

So let’s start with the name, it’s a “coaxial” driver build, or coax, to coax is to be persuasive, these cabinets will be very beautiful and one of my favorite bands R.E.M. have a song called “Pretty Persuasion”. Marketing had a fit over it, they said it was too convoluted so I fired them all and now it’s just me in my garage doing what I want. Makes sense? Alright!

Cost of drivers per cabinet must be under $300 and there are a few other rules as well, check the official thread.

My choice of drivers are the FaitalPro 6HX150 coax ($179 was from online source) combined with the MCM Audio Select 55-5670 8” woofer ($40 each). These model well together and the 8” will have strong response down to 30hz ported and is efficient enough to keep up with the very efficient Faital.

21ec35713466a21f0e269bbd408364c6.jpg


a5c26818d26ce092e4dd5bc56659f4fe.jpg


71528b673d0dd5a755e10cca3f9e603b.jpg


Crossover will be passive as the contest dictates.

Mainly I’m going to be focusing on the enclosure construction for the next few posts. If you’ve been following along my projects over the last year or two, you’ll notice I’m constantly experimenting with new enclosure designs, construction and styles, this project will be no different as I’ll be diving into the world of Kerfing which I’ve never done before.

When I interact with a concept I usually like to do something special with it or something I haven’t seen too much before, and this time I’ll be kerfing solid popular to create a one piece baffle, the enclosure will look veneered but in reality it will be solid wood which I find special/notable.

I did a fair amount of testing initially, but this is a piece I did successfully with poplar, my goal here was to determine the optimal kerf depth so that the wood would bend without breaking

97a73aa6464a4ed3798b1d109218e47f.jpg


847d3175ee8d9eb0fd7db1242b8f4052.jpg


This is another test piece, this was more representative of the actual speaker ID building, however it was with plywood, but it gave me an idea of the curve depth with and spacing and what radius curve it would generate. I used an online calculator to get me in the ballpark, then I fine-tuned using this type of experimentation

d4a008b9bc52cac19f09638010239f72.jpg


dd65b49ef99e94f46aba78fcee863e9a.jpg


This is the wood I’ll actually be using For the speakers, as you can see I found two boards so that the grain will be continuous from one speaker to the other from left to right, as you can see the boards are matched across both speakers. This is very beautiful Poplar heart wood.

f67acb8429c233e4430792956de42a9b.jpg


aedc654a71b0d1d2d9ac41d19b6760d3.jpg


Cutting the boards to their rough final length, the length is determined by the baffle width, the circumference of the radiuses, and the lengths of the sides.

b91d66533ba4cfb43160ac95c78445f3.jpg


To create the height of the speaker, these boards were glued together and reinforced with biscuits

ac0ba2e37de0b8d3b464ba596d81d11e.jpg


6a4e3e2464e6a6a44fb209fe34d8fb98.jpg


0c4bf6f7372c43024b491401d62cb536.jpg


dfeb2763841e1c494a9c6acf00203935.jpg


233d7907ce360d434675d3bb27b98ae4.jpg


The glue up,I used Titebond type III which sets up a little slower in case I want work on the alignment, noticed the clamping techniques ensuring the boards are tight against the clamp bars

Once the glue dried after about 45 minutes, I square one end in my panel saw, them the whole panel in the table saw, I have this set up to cut perfectly square and it does a great job

e18340b7bcc31957976a1a809455879b.jpg


aad7aa4a3cdd755169da93eac1e6f9a0.jpg


Getting ready to cut the kerfs, this is a little fixture I built to reference the fence and allow for subsequent fence movements when Kerfing

56971b58c76efdc1921c943c30f88640.jpg


After the first cut is made, each subsequent cut is spaced 5/16 of an inch using this drillbit, then the next cut is made. Stop block is slid over to the fence and then it’s once again space with the drill bit

ca697252c4c951ce45ef62f3fa104ea6.jpg


And so it goes. The kerfs are all the same distance from each end which locks in the baffle width which will be about 12 inches wide. Kerf depth results in about 1/16” material left.

a8cb6a5cf4d0ce9f17b9fc97a6839d01.jpg


67caa6e86f9e551f7ce939afee4e6994.jpg


First board curved and cut, final angle is about 95° which is intentional to gives the sides some rake

27950ff3b377866b1f99e60ae41a0f97.jpg


7df2604be2e30c18418762943b17cfa8.jpg


Both curves done on both sides, again the middle piece is the baffle and the end pieces are the sides

0588070215f6d2569ce195ca0e5aa755.jpg


I created some spacer boards to go in the back to lock in the final dimensions, there will be three for each glue up

bf0937a48427466fffa049ccfa00d533.jpg


Here you can see how perpendicular the assembly is, with some like clapping it’s sits perfectly flat on my workbench

34699796222b01c8660e9958136330d2.jpg


Next up some glue!

Thanks!
Javad
 
  • Like
Reactions: 1 user
I tested several adhesives to glue the kerfs including media filled epoxy (was overkill and messy to work with), wood glue(too runny) and Loctite construction adhesive which I ended up using. It was thick and didn’t run, squeezed nicely into the voids to support the “veneer surface”, and had great adhesive strength.

Since the cabinet would be heavily braced, ultimately there will be very little load on the kerfs, I think even with proper construction you wouldn’t even have to glue the kerfs, the bracing and ribs of the enclosure will hold everything to shape. It’s also interesting to note how much spring pressure there is on a kerf like this, it takes substantial pressure the bottom out the kerfs and hold the shape so really gluing is a great idea.

fe04adc7563c3d620a5ec4badc0521e7.jpg


88d4a5c6a7a811696c04f55652a84fe7.jpg


8ce9f5cfd06fec1b2f2180c6ec2335a3.jpg


259a91af435ab2aeb0936ebc614dd494.jpg


I built some spacer blocks to set the final width out of MDF, and used a combination of straps and bar clamps to hold everything while the glue dried for about three days. After 3 days the clamps essentially fell off and all the spring load of the kerfs was gone, a good sign.

4f943d5364a1fd5ed13e028fac164d9b.jpg


16437335f9bca97ab0ec05aa9695154b.jpg


While the glue was drying I decided to work on the midrange sub-enclosure, i used a technique I’ve done before in my Rally Sports and also the 135Hz horn, the reverse horn, The idea being to reduce the number of parallel surfaces and allow the backwave to diffract and be absorbed better than in a simply square or rectangle or enclosure.

An easy way to build one is to cut your parallel top and bottom angles on the tablesaw, for this I chose about 20°, then create a fixture to hold the piece at that angle in the radial chopsaw, and in this case I cut 45° angles to create a three-dimensional trapezoid or a four sided pyramid.

0b63e7f306cd40156eb4b96073a7e2b6.jpg


f1353ce894c8621ecb356157859652a9.jpg


Each time a cut is made the board is flipped and cut the other way

4439b9c72ade650b5e26ed64ceb5a249.jpg


And this is easily glued together with tape

a73e9a9a496ba7201b8544cd186f8923.jpg


ea98325e4a0fc290f796e8648197fbd8.jpg


2e724ab5ca705f3d1a7176f78d1a5a8d.jpg


I wanted to add a little more volume and depth so I created a small riser block of 1.5 inches high

884ab0246e74fe0f08c1e4a70c81bf2d.jpg


ad463f706ba0afaf519f26585b657cec.jpg


To finish it off I added another small deflector at the bottom flat part of the enclosure, just to interact with any higher frequencies

45ecc2167d098d367a1b494195753d0b.jpg


473696ac4c23849866e74e46a409da3b.jpg


Since my back panels now had angles, I wanted to the square them to each other so I can simply add a back without having to cut any fancy angles. For this I used my handy new cross cut sled that I built, and simply fixtured each enclosure on the sled and easily made the cuts.

2f0973df6026e2c0b1ddc2de2941aaf8.jpg


547752ce22af01c4726c20e7805bc60e.jpg


Gluing up more panels for the back top and bottom of enclosure

df2ec846e4593e6a2bf98b0c1c2e6d1f.jpg


Next up I’ll document the bracing.

Thanks!
Javad
 
  • Like
Reactions: 1 user
Ok time for some bracing!

I started with a tracing of each enclosure since they vary slightly, this gave me a template for all the other braces. Ultimately I needed a top and bottom brace, a brace for the midrange enclosure and 3 additional braces approx every 4”

d9466694b8917f97733ddcad0ea79ece.jpg


4d9362b672a746f1caef915f00520f47.jpg


Each brace was cut out with a jig saw and finalized to shape in my Wen desk top oscillating sander (love it btw!)

6120b39ad6fdcd6b128235c0c832c1cc.jpg


b3c0cc02d3e266d77fc77ac447f1b965.jpg


Tracing the midrange enclosure

79a94a30168d36ad1fb1d16b656a69d0.jpg


860b6f6625e94b168d792a84da4a0aed.jpg


39a9427ceefabacc94dc7a020125dabd.jpg


e8f0f49cf9e682ced64302412d9689b1.jpg


c9c70991c63b7134ff679db709db4f93.jpg


a44bc709704edb34151ea131d1d03af7.jpg


a0ac05bc040ad77e791e2374b3c9ad41.jpg


Port tube plate

5ba3111edc148cc4457afa71608787f3.jpg


Ports are recessed and the ID is purposely undersized so I can flush trim them through the baffle

f25d6fa9f74c8365e48b6c99b0754172.jpg


Here is a vlog I made describing the braces

YouTube

And all glued and finalized braces

Detail of the mid enclosure

6f6edbf2bdefdbbb00a2d057af796da9.jpg


911c325477dc3f4273e50765790b3580.jpg


The end caps are spaced 1/8” from the eventual top/bottom for some CLD treatment

a42718aa33040138d5f7494130a6c769.jpg


Thanks!
Javad
 
  • Like
Reactions: 1 user
Doppler9000 said:
Very nice build.

For others who may try this, I will reiterate the recommendation for Bondo auto body filler. It fills well, is easy to apply and is about one third the cost of the Loctite.



Thanks! I’ve got about $12 of Loctite in the entire build (2 tubes) so not bad at all, I didn’t test bondo as it’s more a filler than an adhesive (obviously has adhesive properties) but media filled epoxy worked very well. The amount of spring is tremendous with these kerfs and the Loctite did a great job of holding the shape of the kerfs until I added all the bracing in to completely lock it together.

Appreciate your comments and your following along!

Javad
 
Time to install some drivers!

This is the layout

465fba5afa2772f9fb56ea843c7111da.jpg


As I’ve done before, this is the process for an odd shaped driver Template.

First protect your driver and screw it down to a sacrificial MDF panel, 1/2” works great.

8effab9c963a5ea575bf3ccef4eb277c.jpg


Next with a perfectly centered router base, trace around the frame with a 1/4” spiral bit, put an even layer of masking tape around the driver frame to slightly over size the template

d3b18cf4ec3f4baf90e36f6e698199ca.jpg


Now on a new sacrificial piece, trace around the inside of the first sacrificial Template

f21d8f19914b8c963662b37df92d707a.jpg


This leaves you with a template 1/4” oversized

586cb09c58d784cad2af0d9b12a3e951.jpg


Now using a 3/4” Templating fixture, trace around the second sacrificial template to get the final template perfectly sized to the driver

3b89540da456767916bfcd2cb1b7ee08.jpg


a0d1326fc6d6dc24939e6082af5dc3a4.jpg


f84f16ad448ed9684838fa100afe23a2.jpg


With centering reference lines it is quick and easy to align the fixture on your baffle

b595531623e38ca01c657f8cd91ca450.jpg


Here is a quick blog describing the process: YouTube

Here we have two enclosures ready to destroy, I mean flush mount drivers in! =)

e80c754a23ea985da3c9e1fef520028f.jpg


Test cuts finalizing OD, ID and recesses

5e3d28bc9d1712b10cd64b8fe82a8b34.jpg


Marked and ready to go with logic check tracings

2cc279432e642fcec5c834e3f008d157.jpg


Midrange ID cut

b892f6fc19a09a8d2550cba26848bf10.jpg


8” recess and cutout

c4ef76bc8264e0e2081c88ba9857c61a.jpg


5193562dd0ebc2c7fbde82b864566902.jpg


Position driver exactly where it needs to go, install fishing line in driver holes

4bdd20177791f5e1362ef656c46da6e0.jpg


Now with double sided tape on template, slide it over the driver frame and attach it firmly, then pull the driver out. This process perfectly positions the template centered around the driver cutout

c09f1b45ecfd37e8b32286aa4b7233b3.jpg


a03440a4a23632b9a496b5e630c13d69.jpg


2518e5f8debc31c105f243ba6db5f8b9.jpg


Flush trim bit

2780baa145b5df54d423d64b78a66e66.jpg


And router

850b6c7f9abb82242f5ccc4daa6536ee.jpg


Test fit

dbfa625dd76c7301788b79e07420be36.jpg


Next port tube routering.

Thanks!
Javad