Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Multi-Way Conventional loudspeakers with crossovers

DIY PMC MB2 clone
DIY PMC MB2 clone
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 15th July 2017, 10:10 AM   #1
WalterPPK is offline WalterPPK  Netherlands
diyAudio Member
Join Date: Apr 2012
Hi, a couple of years ago we built our own recording studio.
This week we sold our old monitors and I'm now looking at building PMC MB2 clones.
This is what I have in mind:
DIY PMC MB2 clone

First I took a look at JamieMatrix's thread but didn't find any definite dimensions for his build.

The following units are on the list:

Volt RV3143
Volt VM752
Scanspeak D3004/6600

In the first stage a DCX is going to be used. Later on maybe a DEQX or something similar.

I made a fair amount of subwoofers but never a transmission line. I hope that I can get some help with the internal dimensions.

I made a 3D model based on the PMC 2D drawing found in Stargeezerme's thread with the cross section unfolded. The lines of the unfolded section are equal to the lines in the model of the cabinet. Changes in the cabinet will be reflected in the cross section automatically.

Cabinet width (internal): 344mm
Gross cabinet volume: 134L
Nett cabinet volume (-woofer,-mid, -ribs): +/-125L
Sd woofer: 479 cm^2
Offset center woofer: 27mm
Fs woofer: 34hz (or 31hz I read in another thread?)
Sl: 297cm^2 (copied from PMC drawing, including fillet)
So: 1204cm^2
I have a lot of questions but the the first one that came to mind is how do you incorporate the fact that the mouth is bend 90 degrees to the baffle in the unfolded cross section?
As seen on this photo.

This is the first sketch I made from some assumptions of the drawing and photo's found.

DIY PMC MB2 clone

DIY PMC MB2 clone

Hopefully, with some help from you, I can make this thing!

Last edited by WalterPPK; 18th July 2017 at 09:44 AM.
  Reply With Quote
Old 15th July 2017, 10:26 AM   #2
Mooly is offline Mooly  United Kingdom
diyAudio Moderator
Mooly's Avatar
Join Date: Sep 2007
DIY PMC MB2 clone
Walter... we are experiencing some forum issues at the moment.

The reason your edited post disappeared is because as a new poster you are under moderation. Unfortunately we can't currently re-approve edited posts and so in this case I was able to paste your new reply into your following post.
  Reply With Quote
Old 15th July 2017, 11:01 AM   #3
WalterPPK is offline WalterPPK  Netherlands
diyAudio Member
Join Date: Apr 2012
Would a few extra ribs placed in the right bottom corner and near the mouth improve the cross section and reduce internal volume and reduce the TL length?

DIY PMC MB2 clone

Last edited by WalterPPK; 15th July 2017 at 11:25 AM.
  Reply With Quote
Old 15th July 2017, 11:03 AM   #4
WalterPPK is offline WalterPPK  Netherlands
diyAudio Member
Join Date: Apr 2012
Thanks Mooly for re-posting it! Cost me some time to make the post.
  Reply With Quote
Old 15th July 2017, 11:36 AM   #5
WalterPPK is offline WalterPPK  Netherlands
diyAudio Member
Join Date: Apr 2012
This also would be aesthetically more pleasing:

DIY PMC MB2 clone
  Reply With Quote
Old 15th July 2017, 01:46 PM   #6
WalterPPK is offline WalterPPK  Netherlands
diyAudio Member
Join Date: Apr 2012
Nett internal volume is now 120L
  Reply With Quote
Old 15th July 2017, 07:33 PM   #7
Bigun is offline Bigun  Canada
diyAudio Member
Bigun's Avatar
Join Date: Jan 2009
Location: Waterloo, ON or Herefordshire UK
DIY PMC MB2 clone
"The test of the machine is the satisfaction it gives you. There isn't any other test. If the machine produces tranquility it's right. If it disturbs you it's wrong until either the machine or your mind is changed." Robert M Pirsig.
  Reply With Quote
Old 12th August 2017, 12:00 PM   #8
wae is offline wae  Netherlands
diyAudio Member
Join Date: Sep 2013
Location: Aalten
Default PMC Clone?

Hi WalterPPK,

I'm not sure you will find a specific detailed clone design here, for (my view) a number of reasons;

- We don't know what drivers they (specifications vary from the default drivers?) use, do we?
- SO, we don't know what we are designing. As you most likely are well aware, it starts with the driver. (The VOLT 3134 is a good driver for TL, but expensive. There are other very good drivers at half the price or even less). So we might think, Aaaha, they (PMC) use the Volt driver we can purchase, which might not be the case.
- Result, IF we would know in detail how the TL of PMC is designed AND use the standard Volt driver, we might still end up with a big misfit at "large" cost.
- I don't think that the forum members with detailed knowledge on this subject are willing to help you clone a commercial brand speaker, even if you just intend to use it for personal use only.
- There are some threads in the forum about these designs, I think the best would be
Transmission Line Question
- They use a spreadsheet from Martin J. King, who has published in detail how a TL works and can best be designed. This is no longer publicly available for reasons I'm unaware off. HOWEVER, there are VERY good articles from M.J. King on the internet explaining in detail how to design a TL

Which brings me to the following;

Why don't you use TL design software to build your own design, IF you like the appearance of the PMC and want to use the Volt, then THAT's your starting point.

I use Leonard Audio software (info on their forum as well) Transmission Line Modelling Software. If you read the King articles and use the basic principles for the TL design (derived from the T&S of the driver) you will be up and running in no-time.

I've also NEVER designed a TL, because "they say" it is a complicated animal. Now I dived into it, it seems that the damping could be a struggle. On the other hand, the LA software shows all detail about type of damping and volume of damping. I may post a new thread of these designs, ALSO found a nice theoretical design methodology for this damping questions (WHERE to place HOW MUCh of WHAT). The LA software tells me my methodology works. Don't have a clou how it will sound, that's future surprises (positive or negative).

I build a simpel spreadsheet myself (based on M.J. King design principles) to calculate the starting numbers for a TL for a given driver. ALSO modelled some PMC LOOK-ALIKEs. They come close to the dimensions of the real deal, although they differ, but I don't care, I want my own design.

Will start building 3 TL designs in very near future;
- A complete own design for a pair of Tannoy K3149 (as my personal home studio mid-fields)
- A PMC MB2 OR IB2 look alike, drivers to be decided but most likely low-end Dayton audio or Faital Pro. Look VERY promising on paper.
- A PMC look-alike 5" or 6" near field (as my personal home studio near fields).

I am planning to start a studio line / home recording speaker line in near future.

Which reminds me of your drawing for the control room, looks like you use those big MB2's as near fields? Are you SURE?

Any way, my first 5 cents
"If i ain't broken, DON'T fix it"
  Reply With Quote
Old 12th August 2017, 01:43 PM   #9
WalterPPK is offline WalterPPK  Netherlands
diyAudio Member
Join Date: Apr 2012
Hi Wae, you are absolutely right. This is also why I decided to divert from the MB2 design because they are too big to use in near field operation. Second; the outcome is too uncertain because of the difficulty of designing the TL enclosure.
The plan is now to build a bass reflex monitor around the following drivers:

1x SB Acoustics TW29RN-B
1x Volt VM752
2x SB Acoustics W024P-8

The units are ordered and the design pictures will follow. Outer dimensions will be approximately HxWxD 650x400x440 Gross internal volume 90 liter. Tuned to 28hz.
  Reply With Quote
Old 13th August 2017, 11:08 AM   #10
C37 is offline C37  Belgium
diyAudio Member
Join Date: Mar 2003
Location: Brussels
Just for Your information there is a thread here where a member has monted the Volt (or was it atc?) Midrange in a spherical enclosure and reported that a midrange dip he quite never managed to remove otherwise was gone and that it eased the filtering. Can't remember whom right now.
Ohm sweet ohm
  Reply With Quote


DIY PMC MB2 cloneHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
PMC OB1 clone vincentrubble Multi-Way 9 7th September 2018 10:38 PM
Clone of PMC DB1+ ??? Bigun Multi-Way 39 22nd April 2018 10:38 AM
PMC MB2S CLONE stargeezerme Full Range 41 30th December 2017 10:02 AM
fs PMC MB2'S...LOW PRICE!!! mitch112 Swap Meet 0 24th August 2010 07:59 PM
PMC XB2, MB2 vent dimension gengis Subwoofers 1 23rd March 2005 10:02 PM

New To Site? Need Help?

All times are GMT. The time now is 10:58 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 14.29%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio