
Home  Forums  Rules  Articles  diyAudio Store  Blogs  Gallery  Wiki  Register  Donations  FAQ  Calendar  Mark Forums Read 
MultiWay Conventional loudspeakers with crossovers 

Please consider donating to help us continue to serve you.
Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving 

Thread Tools 
3rd June 2017, 02:53 PM  #1 
diyAudio Member
Join Date: Oct 2015

Inductor unwinding calculations?
Hello people of diyaudio!
I was given by a friend a set of generic Visaton crossover networks (HW2/70NG). I would like to put them in use for a pair of 2 way speakers. I have already established the values for the 2nd order filters using XSim, and i need to lower the 1mH low pass inductor to around 0.56mH (exact value is not critical, what matters most is that i reduce both by the same amount). The inductor has 16 verical layers (or stacks?) by 14 horizontal layers (hope the pictures make more sense). So there should be around 224 turns of 1mm copper wire. The coil internal diameter is 18mm, the outer diameter is 45mm, and the coil hight is 15mm. Is there anyone cunning enough to tell me how many turns should i unwind in order to achieve this value (0.56mH)? 
3rd June 2017, 04:14 PM  #2 
diyAudio Member
Join Date: May 2002
Location: Westende Resort, BE coast

It is probably possible to calculate the required windings for that value using an average winding diameter. Assuming that you are able to measure, I would proceed to remove say 1/3rd of the layers, then measure, then again remove some windings, etc. Should be able to home in to the required value in a few iterations.
After all, this is diy ;) Jan
__________________
Linear Audio  Articles  SilentSwitcher  Treg hivoltage regulator  Hivoltage delay unit  AutoRanger 
3rd June 2017, 04:22 PM  #3 
diyAudio Member
Join Date: Feb 2012
Location: Croatia

Approximately calculating, there is dcr values on Visaton web for the SP1 air core coils. 0,68 mH= 0,4 ohm; 0,47 mH=0,3 ohm; since there is no 0,56 mH to choose from, the middle dcr value of the two would be about 0,35 ohm. 1 mH = 0,5 ohm, so you'd need to remove the excess of 0,15 ohm of wire to arrive closer to 0,56 mH. Find the characteristic resistance per meter for the copper wire of 1 mm diameter and you can solve for the length of wire by dividing the two values.
You could build this jig to measure directly with a 1 kHz mp3 pure sine wave or search for a coil calculator.
__________________
https://www.diyaudio.com/forums/mult...ildplans.html 
3rd June 2017, 06:17 PM  #4 
diyAudio Member
Join Date: Oct 2015

OK,
after a little more search, i found this really old post http://www.diyaudio.com/forums/multi...tml#post293905 which helped me calculate the number of turns to be removed. If i did this correctly, i should remove around 56 turns. Thanks all! Last edited by filthyone; 3rd June 2017 at 06:25 PM. 
5th June 2017, 09:52 PM  #5 
diyAudio Member
Join Date: Aug 2006

Decent LCR meters are only $4050
__________________
~Brandon Please help my waveguide and box construction research by donating to my gofundme via my website:Soma Sonus 
5th June 2017, 10:22 PM  #6 
diyAudio Member
Join Date: Nov 2005

If i did this correctly, i should remove around 56 turns.
That sounds about right. 
6th June 2017, 12:59 AM  #7 
diyAudio Member
Join Date: Aug 2008
Location: Portsmouth UK

56 turns, or about a 1/4 of the 224 sounds dead right.
Inductance is the square of the number of turns, disregarding varying size of turns. 3/4 squared is 1mH X 9/16, which should be about 0.56mH. I'd always take off a bit less, then measure. SP coils The data for 1mm windings is saying the resistance should drop from 0.5R to about 0.37R.
__________________
Best Regards from Steve in Portsmouth, UK. 
6th June 2017, 03:37 AM  #8 
diyAudio Member
Join Date: Mar 2009
Location: Buenos Aires  Argentina

You have 16 layers of 14 turns each, so 224 turns total
To reduce from 1mH to 0.56mH you must reduce inductance to 56% of original value. Since inductance varies with the square of turns, you need to reduce winding to square root of 56% so to 0.75 of turns , so to 168 turns. You must unwind and discard 224168=56 turns.
__________________
Design/make/service musical stuff in Buenos Aires, Argentina, since 1969. 
Thread Tools  


Similar Threads  
Thread  Thread Starter  Forum  Replies  Last Post 
Unwinding a steel laminate core inductor? Formula?  AudioLapDance  Parts  1  18th February 2009 02:27 AM 
unwinding a 1mh. steel laminate inductor into .8mh, good idea or not?  marchel  MultiWay  17  20th February 2008 09:44 AM 
unwinding inductor  chainenoble  MultiWay  2  31st January 2007 10:29 AM 
Inductor calculations  jaudio  MultiWay  4  12th August 2006 11:48 PM 
Unwinding my inductor to obtain lower inductance  michael  MultiWay  11  6th January 2004 07:10 AM 
New To Site?  Need Help? 