Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Headphone Systems Everything to do with Headphones

RJM Audio Sapphire Desktop Headphone Amplifier
RJM Audio Sapphire Desktop Headphone Amplifier
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 11th February 2019, 01:31 AM   #1471
itsikhefez is offline itsikhefez  United States
diyAudio Member
 
Join Date: Aug 2015
RJM Audio Sapphire Desktop Headphone Amplifier
Quote:
Originally Posted by rjm View Post
14 ohms is quite punishing, even if the efficiency is reasonable. You can see from the attached image that the output power of the Sapphire in the standard 37.5 mA bias configuration drops off considerably below 60 ohms.

There is nothing about the circuit that makes it incapable of driving these loads with low distortion however, it's just that raising the bias current would be optimal.
Thanks for the info.
What changes need to be made to increase the bias current? (I believe mine was a 4.1t version).
How much higher would you go? 75, 150?
  Reply With Quote
Old 11th February 2019, 04:38 AM   #1472
itsikhefez is offline itsikhefez  United States
diyAudio Member
 
Join Date: Aug 2015
RJM Audio Sapphire Desktop Headphone Amplifier
Quote:
Originally Posted by rjm View Post
14 ohms is quite punishing, even if the efficiency is reasonable. You can see from the attached image that the output power of the Sapphire in the standard 37.5 mA bias configuration drops off considerably below 60 ohms.

There is nothing about the circuit that makes it incapable of driving these loads with low distortion however, it's just that raising the bias current would be optimal.
Quote:
Originally Posted by itsikhefez View Post
Thanks for the info.
What changes need to be made to increase the bias current? (I believe mine was a 4.1t version).
How much higher would you go? 75, 150?
OK I took a look at the notes in the spreadsheet and seems like I need to change R11, R12.

A few questions:
1) Based on your graph, 75mA seems insufficient still. Since it's hard to see where 14ohm lands on the graph, what would be the optimal value? I assume somewhere between 100-150 ?
2) I assume that even if I go for 150mA, the default R17/R18 of 4.75 should remain?
3) Is the gain calculation the same after changing R11/R12?

EDIT:
Just stumbled upon #5443967 and saw the values in the updated BOM.
I will follow that for 150mA...would appreciate any other thoughts worth considering.

Thanks!

Last edited by itsikhefez; 11th February 2019 at 04:47 AM.
  Reply With Quote
Old 11th February 2019, 07:29 AM   #1473
itsikhefez is offline itsikhefez  United States
diyAudio Member
 
Join Date: Aug 2015
RJM Audio Sapphire Desktop Headphone Amplifier
To my understanding these headphones require 200mW @ 16ohms. Based on the graph, the 75mA is not sufficient but 150mA seems overkill.
Given the large caps required, perhaps 100mA or 125mA would be better?
  Reply With Quote
Old 11th February 2019, 12:05 PM   #1474
rjm is offline rjm  Japan
Richard Murdey
diyAudio Member
 
rjm's Avatar
 
Join Date: May 2004
Location: Kyoto
RJM Audio Sapphire Desktop Headphone Amplifier
Quote:
Originally Posted by itsikhefez View Post
To my understanding these headphones require 200mW @ 16ohms. Based on the graph, the 75mA is not sufficient but 150mA seems overkill.
Given the large caps required, perhaps 100mA or 125mA would be better?
My answer I tried to post earlier got zapped as diyaudio went offline for a while.

Anyway ... the latest BOM you can download from my website gives more info on the bias current mods. There is no change between it and the 4.1t BOM, other than the electrolytic capacitors have been reduced in number and increased in size.

But, no, no one "needs" more than a couple of mW of headphone output power. Much like solid state power amplifiers, its a question of headroom and dynamic reserve rather than clipping distortion. So it's a matter of will it sound better, which in turn is a question of whether the additional distortion and noise from running at higher bias current will or will not balance the reduction in distortion achieved by the increased headroom.

My recommendation stands: for 60-300 ohms, use the standard configuration. for 16*-60 ohms, use 75 mA.

*14 or 15 ohms, also. Close enough.
__________________
RJM Audio | phonoclone.com
  Reply With Quote
Old 13th February 2019, 08:38 AM   #1475
rjm is offline rjm  Japan
Richard Murdey
diyAudio Member
 
rjm's Avatar
 
Join Date: May 2004
Location: Kyoto
RJM Audio Sapphire Desktop Headphone Amplifier
pcb-sapphire-42b2-bom

New BOM for review. I've changed the Power Options sheet to remove the 150 mA version, keeping the 37.5 mA and 75 mA version.

I've heard the story that the burger restaurants offer a choice of three sizes as a psychological ploy in order to upsell customers to at least buying the medium-size burger.

For the Sapphire amp, the same psychology was operating in a negative sense. The additional choice was causing indecision and confusion. It would be better to settle on just "regular" and "large" options, rather than "small" "medium" and "large". That way most people would go with the normal bias mode, and anyone who didn't would have a clear single choice remaining.

Also, the scaling was wrong anyway. As usual I was overthinking the problem. And 12 W heat dissipation for the stereo circuit at 150 mA is kinda nuts. 75 mA provides plenty of power into low impedance loads. Let's leave it at that.
Attached Files
File Type: zip pcb-sapphire-42b2-bom.zip (424.6 KB, 5 views)
__________________
RJM Audio | phonoclone.com
  Reply With Quote
Old Yesterday, 10:01 AM   #1476
itsikhefez is offline itsikhefez  United States
diyAudio Member
 
Join Date: Aug 2015
RJM Audio Sapphire Desktop Headphone Amplifier
Thanks for the update Richard.. the latest BOM is clearer.

Reading the power graph posted earlier, I was under the impression that both 37.5 and 75mA version would perform the same way for loads above 60ohm, thus the 75mA would be a more versatile choice for any headphone from 16-300ohms.

Quote:
Originally Posted by rjm View Post
So it's a matter of will it sound better, which in turn is a question of whether the additional distortion and noise from running at higher bias current will or will not balance the reduction in distortion achieved by the increased headroom
Does the 37.5mA perform "better" for high impedance cans because the extra headroom is not needed and distortion is added?
  Reply With Quote
Old Today, 08:08 AM   #1477
itsikhefez is offline itsikhefez  United States
diyAudio Member
 
Join Date: Aug 2015
RJM Audio Sapphire Desktop Headphone Amplifier
Silly question but which caps are considered in the power supply and which signal path ?
  Reply With Quote

Reply


RJM Audio Sapphire Desktop Headphone AmplifierHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
RJM Audio Sapphire Headphone Amplifier rev14a1 kit rjm Group Buys 14 3rd September 2016 12:23 AM
RJM Audio Gainbloc Preamplifier Mk. I rjm Analog Line Level 11 8th September 2011 12:59 AM
Parts for RJM Audio/47 Labs Phoneclone jim rose Swap Meet 0 15th May 2011 07:55 PM
New Desktop Tube Amplifier, 6V6 SE Musik007 Twin Audio 11 6th October 2010 05:23 PM
FS: DIY Cavalli Audio Embedded Hybrid Headphone Amplifier sachi Swap Meet 4 19th May 2010 10:43 PM


New To Site? Need Help?

All times are GMT. The time now is 09:41 PM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.00%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright ©1999-2019 diyAudio
Wiki