PeeCeeBee V4H GB

[shaan]

Boards home.

Invoice for shipping charge will be sent from tonight. Members who have already paid shipping charge please notify me if there is any change in delivery address.

Thanks for your patience.
shaan

 

[shaan]

GB3 Update

CitizenKane - 6 PCBs - SHIPPING PAID
delange - 4 PCBs + 4 Pair MOSFETs - SHIPPING INVOICE SENT
gusto142 - 2 PCBs - SHIPPING INVOICE SENT
samratsarkar - 2 PCBs - SHIPPING PAID
md_Stryker - 2 PCBs + 4 Pair MOSFETS - SHIPPING PAID
outtek - 2 PCBs - SHIPPING INVOICE SENT
supernet - 2 PCBs - SHIPPING INVOICE SENT
anilrao - 2 Modules - SHIPPING PAID
janho12345 - 2 PCBs (+2 PSU PCBS) - SHIPPING PAID
force of 1/2 - 2 PCBs + 4 Pair MOSFETs - SHIPPING INVOICE SENT
Rick G - 2 PCBs - SHIPPING INVOICE SENT

 

[kpsthakur]

H Shaan, please add a pair of fully loaded V4H Boards for me too, I would also need a PSU board. Will add my name to the over all tally for reference

 

[kpsthakur]

GB3 Update

CitizenKane - 6 PCBs - SHIPPING PAID

delange - 4 PCBs + 4 Pair MOSFETs - SHIPPING INVOICE SENT

gusto142 - 2 PCBs - SHIPPING INVOICE SENT

samratsarkar - 2 PCBs - SHIPPING PAID

md_Stryker - 2 PCBs + 4 Pair MOSFETS - SHIPPING PAID

outtek - 2 PCBs - SHIPPING INVOICE SENT

supernet - 2 PCBs - SHIPPING INVOICE SENT

anilrao - 2 Modules - SHIPPING PAID

janho12345 - 2 PCBs (+2 PSU PCBS) - SHIPPING PAID

force of 1/2 - 2 PCBs + 4 Pair MOSFETs - SHIPPING INVOICE SENT

Rick G - 2 PCBs - SHIPPING INVOICE SENT

Kamal Thakur -2 PCB (full kit) + PeeCeeBee PSU Board (full kit) for 54V operation

 

[shaan]

GB3 Update

CitizenKane - 6 PCBs - SHIPPING PAID
delange - 4 PCBs + 4 PAIR MOSFETs - SHIPPING PAID
gusto142 - 2 PCBs - SHIPPING PAID
samratsarkar - 2 PCBs - SHIPPING PAID
md_Stryker - 2 PCBs + 2 PSU PCBS + 4 PAIR MOSFETS - SHIPPING PAID
outtek - 2 PCBs - SHIPPING PAID
supernet - 2 PCBs - SHIPPING PAID
anilrao - 2 MODULES - SHIPPING PAID
janho12345 - 2 PCBs + 2 PSU PCBS - SHIPPING PAID
force of 1/2 - 2 PCBs + 4 PAIR MOSFETs - SHIPPING PAID
Rick G - 2 PCBs - SHIPPING PAID
kpsthakur - 2 MODULES + 1 PSU MODULE - SHIPPING PAID

 

[shaan]

GB3 Update

CitizenKane - 6 PCBs - SHIPPED
delange - 4 PCBs + 4 PAIR MOSFETs - SHIPPED
gusto142 - 2 PCBs - SHIPPED
md_Stryker - 2 PCBs + 2 PSU PCBS + 4 PAIR MOSFETS - SHIPPED
outtek - 2 PCBs - SHIPPED
supernet - 2 PCBs - SHIPPED
janho12345 - 2 PCBs + 2 PSU PCBS - SHIPPED
force of 1/2 - 2 PCBs + 4 PAIR MOSFETs - SHIPPED
Rick G - 2 PCBs - SHIPPED
samratsarkar - 2 PCBs - SHIPPING PAID
anilrao - 2 MODULES - SHIPPING PAID
kpsthakur - 2 MODULES + 1 PSU MODULE - SHIPPING PAID

 

[gtose]

My V4H update

Time for an update from my original post in February (https://www.diyaudio.com/forums/group-buys/317151-peeceebee-v4h-gb-72.html#post5691617). 2 months into daily listening and I haven't run into any stability issues and the V4H has continued to occupy my number 1 spot in my listening setup! Again, thank you for such a great amp Shaan!

I've also now completed the work on the front panel and handles for my V4H chassis and wanted to share some glamour shots. The front panel is made up of a 1/4" 6061 base plate which is used to mount the softstart and resistor and mount the front to the inner frame. To hide those screws, I milled out 3x 1/2" plates that are tapped from the rear. Then brass hardware and an engraved nameplate was added. The handles were milled out of 1" 6061 (quite a challenge on my hobby desktop CNC), tapped, and bolted on from the inside.

Only thing left to cut are the top and bottom covers and then move it to its spot on the shelf!

 

[Vunce]

Hi G,
Fantastic V4H amplifier build!!
Your chassis work makes me envious, great job.
Enjoy your new baby, as you already know, it sounds excellent

 

[Harry3]

Congratulations. Neat wiring and plenty of heat sinks.
Envy the metal work.

 

[shaan]

Time for an update from my original post in February (https://www.diyaudio.com/forums/group-buys/317151-peeceebee-v4h-gb-72.html#post5691617). 2 months into daily listening and I haven't run into any stability issues and the V4H has continued to occupy my number 1 spot in my listening setup! Again, thank you for such a great amp Shaan!

I've also now completed the work on the front panel and handles for my V4H chassis and wanted to share some glamour shots. The front panel is made up of a 1/4" 6061 base plate which is used to mount the softstart and resistor and mount the front to the inner frame. To hide those screws, I milled out 3x 1/2" plates that are tapped from the rear. Then brass hardware and an engraved nameplate was added. The handles were milled out of 1" 6061 (quite a challenge on my hobby desktop CNC), tapped, and bolted on from the inside.

Only thing left to cut are the top and bottom covers and then move it to its spot on the shelf!

Awesome! I couldn't be happier to know the v4h topped for you! Happy listening.

And that frontplate is a looker!

 

[bvtrinh]

Fantastic looking amp Gtose! I bet it doesn’t get hot at all.

Bao

 

[abanico]

Gtose ,can you share the source of these green leds you are using ?

 

[gtose]

Thanks all for your kind comments! I just finished up the top and bottom panels and finally have it on the shelf

@abanico, the panel mount LED is 12V, 12mm panel diameter and is available in a number of different bezel types and colors: DC12V 12mm Thread Diameter Metal Red White Blue Green LED Signal Indicator Light | eBay.

Greg

 

[abanico]

Thanks for the link ,everything in your amp is nice .Really is was thinking on the boards leds , i don't like red ones and can't find any different colour close to 1,8 vf.

 

[gtose]

@abanico, oh those LEDs , too many green LEDs (or is there such a thing?). Here are the ones I ordered from DigiKey: https://www.digikey.com/products/en?keywords=160-1852-ND.

 

[abanico]

Thanks i can buy them on Mouser. I don't like much the led light ,as before i was with tube gears i used 2, 24 v mini incandescent lamps in serie just to see a part of the filament glow threw a round lens . Never blow one. At home i have two linestra lamps in serie working just 40 years now.

 

[delange]

... (quite a challenge on my hobby desktop CNC)...

Excellent work!
What kind of CNC desktop machine do you have?
I have been playing with the idea of buying one too.

 

[anilrao]

Received my modules yesterday, looks beautiful.
Great work Shaan.



Anil

 

[outtek]

Hi Shaan, can you please share the expedition details for my packet please (tracking number).
Thanks.

 

[gtose]

Thanks delange!

What kind of CNC desktop machine do you have?

It is a Shapeoko 3 XL with a bunch of upgrades, 1.5kW water cooled spindle, reinforced Z-axis, etc. Some details from a few years ago are at My 1.5kW water cooled SO3 XL - Shapeoko - Carbide 3D Community Site.