Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

TABAQ TL for Tang Band
TABAQ TL for Tang Band
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 30th June 2020, 07:45 AM   #3051
nas3000 is offline nas3000  Lithuania
diyAudio Member
 
Join Date: Sep 2016
Location: Vilnius
Quote:
Originally Posted by GM View Post
Translating to nothing........ Per the chart, a shelf vent has a 2.227 'pipe' end correction, though without access to my own calculator based on measurements, not on pipe end corrections per se, I can't say how accurate it is other than it's my understanding that the chart has been vetted/well proven by others, both pro and DIY.

Re when does a reflex, which is presumed to have a uniform particle density air mass 'plug', change to a 1/4 WL resonator [MLTL, etc.], is when simmed using accurate pipe/horn theory, the 'visible' and/or measured turnover point is when the reflex calculated alignment is 'stretched' to a high enough aspect ratio [pipe compression ratio [CR] to my way of viewing it] that the vent is becoming too long for a given vent area [Av], i.e tuning [Fb, Fp] is 'creeping' lower due to increasing 1/4 WL pipe action increasingly damping the vent with increasing CR.

I currently only have Hornresp [HR] loaded, which has no shelf vent option and otherwise WRT accuracy only know that it's good enough when the vent is a reflex [hole in a box], be it just a box or some type of MLTL and one pipe vent MLTL recently done by 'Scottmoose' in MJK's software for comparison.

All that said, historically it was recommended to start with too large and or too long a vent and do final tuning in-room and IME, many times I had to tune each cab individually for best overall in room performance; though admittedly I'm from the era of 'acoustic solutions to acoustic problems' since highest practical acoustic efficiency was a primary goal, whereas today with ~affordable, high SQ, all encompassing DSP, cheap high power; speaker design has become mostly moot in [casual] DIY, consumer HIFI/HT apps.

GM



Dear GM,


It may be my language barrier, but... Are you talking about personal calculator, which differs a little from the publicly known formulas?



Or there is another things to consider vent tuning, when building MLTL?


Both???
  Reply With Quote
Old 30th June 2020, 07:54 AM   #3052
perceval is offline perceval  Taiwan
diyAudio Member
 
perceval's Avatar
 
Join Date: Feb 2014
Location: Taiwan
So, tilting works fine.
I have the SB65 pushed back 15cm from a plumb line aimed at the base.

It is also great to better time align the woofer to the full range.

Nas, as I have stated, only the frequencies higher than 200Hz were affected, anything under, I guess the wavelengths are just too great to be affected by such a small change.

That room has bass traps in all 4 corners, but I still get dips and peaks in the lower frequencies if I move around the room.
  Reply With Quote
Old 2nd July 2020, 08:35 AM   #3053
Entas is offline Entas  Lithuania
diyAudio Member
 
Join Date: Jun 2019
Location: Kretinga
Hello,

I have attached a picture of two TABAQs. Which one looks better for you? Left one has a vent at the bottom and the right one, has a vent in the middle of the CSA (second attachement).
Attached Images
File Type: jpg Front.jpg (78.1 KB, 89 views)
File Type: jpg Front2.jpg (52.5 KB, 88 views)
 

Reply


TABAQ TL for Tang BandHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Tang Band W3-593SF vs. Tang Band W3-926SD Zaputh Full Range 17 5th June 2009 11:37 PM
Tang Band MTM ? wrenchone Multi-Way 11 21st November 2007 06:39 PM
8 x 12 Tang Band troystg Subwoofers 3 2nd February 2007 03:37 AM
Tang-band 2-way (W3+W8) haffe Multi-Way 10 31st January 2007 11:11 PM
New Tang Band is BUSTED! Zero Cool Subwoofers 6 8th May 2006 04:15 PM


New To Site? Need Help?

All times are GMT. The time now is 02:40 AM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.79%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Copyright ©1999-2020 diyAudio
Wiki