Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

MLTL minus correction circuit
MLTL minus correction circuit
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 11th October 2007, 05:21 AM   #1
Shae is offline Shae  Australia
diyAudio Member
 
Join Date: Oct 2007
Default MLTL minus correction circuit

hi, does anyone here have much experience with the martin j king fostex fe206e MLTL design -

http://www.quarter-wave.com/Project05/Project05.html

my question is; not being much of a circuit person (apprenctice carpenter) would it be feasible to build the MLTL design with the fe206e but omit the correction circuit? has anyone tried this out? Or would this idea destroy the design? any advice would be appreciated
  Reply With Quote
Old 11th October 2007, 09:27 AM   #2
Scottmoose is offline Scottmoose  United Kingdom
diyAudio Member
 
Scottmoose's Avatar
 
Join Date: Mar 2005
Location: UK
Well, your ears might start bleeding after a few minutes of listening. The 206 needs correction to work properly in a resonant box. You might get away with it if you can get them near a rear wall and / or corners, tweak the positions so they're a few degrees off-axis, and add 3 - 4 ohms of series resistance. The circuits aren't difficult to make though -there's only 4 components & Martin provides all the values & the diagram.
__________________
"'That'll do", comes the cry of the perfectionist down the ages.' James May -The Reassembler
www.wodendesign.com Community sites www.frugal-horn.com http://frugal-phile.com/
  Reply With Quote
Old 11th October 2007, 09:42 AM   #3
Shae is offline Shae  Australia
diyAudio Member
 
Join Date: Oct 2007
ah i see. well thanks for the advice scottmoose, you have been invaluable throughout my research into full range speakers. but lazyness has triumphed again, and i shall forsake the MLTL and focus my efforts on a pair of ML TQWT's (looks like a separate subwoofer will have to go in place of larger drivers). thanks again for your advice!
  Reply With Quote
Old 11th October 2007, 12:48 PM   #4
Scottmoose is offline Scottmoose  United Kingdom
diyAudio Member
 
Scottmoose's Avatar
 
Join Date: Mar 2005
Location: UK
99.99% of ML TQWT need a BSC circuit too, unless positioned as I indicated above. As do FR units if mounted in a bass reflex, sealed box, transmission line, aperiodic enclosure etc., if you want to run them fairly low.

'Laziness triumps again'? Ye Gods. Is it really such a hardship to to solder two components in parallel in the + lead (and an optional two components across the + & - leads)? Rocket science it isn't. Before reaching the driver you break the + lead. You take two small pieces of wire, which are attached to one end of the + lead. One of these you solder to one end of an inductor, the other you solder to one end of a resistor. You then take an additional two pieces of wire, one soldered to the opposite end of the inductor, the other soldered to the opposite end of the resistor, and the free ends connect back to the other section of the + lead. You could even use cold welds & crimp the wires together, so no soldering required. This is hardly going to cause great mental and physical strain.
__________________
"'That'll do", comes the cry of the perfectionist down the ages.' James May -The Reassembler
www.wodendesign.com Community sites www.frugal-horn.com http://frugal-phile.com/
  Reply With Quote

Reply


MLTL minus correction circuitHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Hawksford output error correction circuit? Jorge Solid State 96 12th December 2011 11:31 PM
Has anyone tried this BS correction circuit? G Full Range 4 14th January 2008 09:11 PM
Modeling a Baffle Step Correction Circuit Seadweller Full Range 4 28th December 2007 09:51 PM
MLTL correction circuit position Lostcause Full Range 7 24th September 2005 01:10 PM
Baffle step correction circuit - how to design? mr_push_pull Multi-Way 28 9th November 2004 08:27 PM


New To Site? Need Help?

All times are GMT. The time now is 06:34 PM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.79%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio
Wiki