Go Back   Home > Forums > > >

Elekit News and products from Elekit

Reply
 
Thread Tools
Old 17th May 2020, 09:51 PM   #1
vkung is offline vkung  Canada
diyAudio Member
 
Join Date: May 2005
Location: Vancouver BC Canada
Default ELEKIT PS 3250 MC/MM phono stage

ELEKIT PS-3250 Phono stage MM/MC $90.00
PS-3250 works well with TU-8200
Itatakachi YM -150 case + the DC input socket +PS-325. All for $175 (available NOW)

The box set includes; $165
1. ELEKIT PS-3250
2. Metal box x 1 pcs Tatakachi YM-150 (pre-drilled)
3. DC jack x 1 pcs
4. Switching AC adapter (5V1A) x 1 pcs
5. 3P toggle SW : x 1 pcs
6. Screw M3 x 6 : 5pcs
7. Alternative source of power supply : USB type C adaptor - to use phone battery ADD: $7.50)




. Cartridge / MM type (about 47 kΩ), MC type (about 100 Ω or 30 Ω)
. Circuit configuration / CR type equalizer (RIAA), two-stage op-amp
amplification
・ RIAA deviation / within 0.5 dB (20 to 20 kHz)
・ Gain (@ 1kHz)
27dB (MM, LOW-G), 32dB (MM, MID-G), 36dB (MM, HIGH-G)
56dB (MC, LOW-G), 62dB (MC, MID-G), 65dB (MC, HIGH-G)
・ Non-clip maximum output (@ 1kHz) / 9V r.m.s.
・ Power supply voltage / DC 5-12V
・ Current consumption / 100mA (at 5V), 30mA (at 12V) [with NJM2068DD]
・ PCB size / 100 80 mm
MADE In JAPAN

Features ]
● In addition to MM type cartridges, it is also compatible with MC type cartridges by replacing jumpers on the PCB board.
The gain can also be set in 3 stages according to the output of the cartridge.
● The op-amp is NJM2068DD (low noise). The op-amp can be replaced, and you can enjoy the fun of op-amp rolling.
● CR type is used for the equalizer circuit, so even if the operational amplifier is replaced with another one, there is no concern that the equalizing characteristics will shift.
● Adopting 1% metal film resistors and 2% film capacitor, RIAA deviation is small and low noise.
● The power supply section is equipped with a positive / negative voltage generation circuit. High sound quality and wide dynamic range are secured by supplying 15V to the op-amplifier.
● Equipped with a POP noise suppression circuit when the power is turned on / off.
● Since the level of noise (especially hum) is greatly affected by the routing of the input / output lines and the ground point of the equalizer amplifier, this kit comes with an input / output jack for mounting on the board, and a grounding bracket.


Click the image to open in full size.


Click the image to open in full size.

Prepare PS-3250 first by soldering it. You also require these parts that are not included in the kit: DC jack, aluminum case, M3, and 5 screws about 8mm long. These parts are included if you purchase the $99 package.
For metal processing your will require center punches, reamers, metal files, drill bits for aluminum and drills.

Click the image to open in full size.

Click the image to open in full size.

takachi ym-180 case (pre-drilled after July 11, 2021)
Click the image to open in full size.

Pre drilled BOX - after July 11, 2021

Click the image to open in full size.

Click the image to open in full size.


DC 12V (solder the DC Jack - does not include in the kit)
The DC jack used has an outer diameter of 5.5 mm and an inner diameter of 2.1 mm.
The inner pin is positive and the outer and outer peripheries are negative.
The AC adapter uses the same standard plug, 5V-12V.
"2.1mm standard jack".
Click the image to open in full size.

USB power source - from phone power or battery pack
Click the image to open in full size.

Click the image to open in full size.

Case Preparation (as at July 11, 2021... Pre-drilled)
Click the image to open in full size.

1. Make a copy of the floor plan found on page 4 in the menu
2. Cut out the floor plan and attach it to the back of the case
3. Follow the guides on the floorplan to drill the holes on the case
Click the image to open in full size.

Click the image to open in full size.

Click the image to open in full size.

Click the image to open in full size.

[Click the image to open in full size.


Click the image to open in full size.

Click the image to open in full size.

Click the image to open in full size.

Last edited by vkung; 21st July 2021 at 01:50 AM.
  Reply With Quote
Old 18th May 2020, 03:26 AM   #2
Wansmith is offline Wansmith  Australia
diyAudio Member
 
Join Date: Feb 2017
Cool! Is the design the same as the phono stage in the Tu8500?
  Reply With Quote
Old 18th May 2020, 03:55 AM   #3
vkung is offline vkung  Canada
diyAudio Member
 
Join Date: May 2005
Location: Vancouver BC Canada
No they are different. This one can adjust the loadings of the cartridge..
Also you can use power source from phone or battery pack via USB adaptor.
  Reply With Quote
Old 12th June 2020, 07:59 PM   #4
vkung is offline vkung  Canada
diyAudio Member
 
Join Date: May 2005
Location: Vancouver BC Canada
Click the image to open in full size.


Available now

USB power source - from phone battery pack via USB-C

Last edited by vkung; 12th June 2020 at 08:12 PM.
  Reply With Quote
Old 10th September 2020, 04:31 AM   #5
vkung is offline vkung  Canada
diyAudio Member
 
Join Date: May 2005
Location: Vancouver BC Canada
ENGLISH MANUAL IS READY
  Reply With Quote
Old 30th May 2021, 05:39 PM   #6
vkung is offline vkung  Canada
diyAudio Member
 
Join Date: May 2005
Location: Vancouver BC Canada
Totally forgot this sleeping beauty
  Reply With Quote
Old 4th June 2021, 05:05 AM   #7
HarryY is offline HarryY  United States
diyAudio Member
 
HarryY's Avatar
 
Join Date: Aug 2017
Location: NY
A ready made case would make this a good seller.

For many making a case is the hardest part.
  Reply With Quote
Old 4th June 2021, 07:28 AM   #8
vkung is offline vkung  Canada
diyAudio Member
 
Join Date: May 2005
Location: Vancouver BC Canada
it is a diy kit...
  Reply With Quote
Old 12th July 2021, 01:41 AM   #9
vkung is offline vkung  Canada
diyAudio Member
 
Join Date: May 2005
Location: Vancouver BC Canada
Today Maker Labs in Vancouver helps me to drill each box.
Now the Box is pre-drilled. You can pick USB-C power supply or from DC adaptor

This unit is ideal for TU-8200R to work with TT
Click the image to open in full size.

Last edited by vkung; 12th July 2021 at 01:56 AM.
  Reply With Quote
Old 20th July 2021, 05:25 AM   #10
vkung is offline vkung  Canada
diyAudio Member
 
Join Date: May 2005
Location: Vancouver BC Canada
Click the image to open in full size.Untitled

Click the image to open in full size.

You can use phone battery to power PS-3250
Click the image to open in full size.

Click the image to open in full size.Untitled

Last edited by vkung; 20th July 2021 at 05:29 AM.
  Reply With Quote

Reply


ELEKIT PS 3250 MC/MM  phono stageHide this!Advertise here!
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Elekit TU-8500 Phono Amp vkung Elekit 15 9th November 2020 11:40 AM
FS: NAIM phono cards, good for diy phono stage. piecor Swap Meet 11 29th May 2015 11:04 AM
Adding a 3rd gain stage to an MM phono stage, to make it suitable for LOMC? andyr Analogue Source 10 16th August 2012 04:10 AM
Should I replace Scott 222C phono stage with Claret phono stage? Bing Yang Analogue Source 0 22nd August 2005 06:41 AM


New To Site? Need Help?

All times are GMT. The time now is 01:45 PM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.00%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.
Copyright ©1999-2021 diyAudio
Wiki