Elekit 3249 R DAConvertor install in TU 8200DX

mrobertweiss · 12th January 2019, 07:53 PM

Where does one pick up the 5 volt DC supply to the usb module, from the 8200 board, if one does not wish to power the unit from the PC usb port? This appears to utilize the jumpers at 1,7,9 for "self" power as opposed to "B" for usb 3.3volt sourcing.
Most of the little manual is in Japanese, so I may be misconstruing how the component is to be used. The output from the DAC utilizes a 3.5 mm minijack which connects to another minijack next to the 8200 amp's Line 2 RCA inputs, (inactivating them when it is engaged)

vkung · 12th January 2019, 08:15 PM

send your email address to infp@vkmusic.ca I will send you the English manual

mrobertweiss · 13th January 2019, 12:37 AM

I read these instructions for the 8100, but it seems to me that is a different device, the minijacks on the back of the 8200 obviate the need for the shielded cable piece in the instructions you made for the 8100, if I am not mistaken.

I just wanted to pull the power for the little board from the amp, rather than from the computer via usb.....seemed more efficient, although i may just be ignorant.

vkung · 13th January 2019, 04:48 AM

TU-8100 requires shielded cable. TU-8200 use the 3.5mm male to male cable

12th January 2019, 07:53 PM	#1
mrobertweiss diyAudio Member Join Date: Jan 2019	Elekit 3249 R DAConvertor install in TU 8200DX Where does one pick up the 5 volt DC supply to the usb module, from the 8200 board, if one does not wish to power the unit from the PC usb port? This appears to utilize the jumpers at 1,7,9 for "self" power as opposed to "B" for usb 3.3volt sourcing. Most of the little manual is in Japanese, so I may be misconstruing how the component is to be used. The output from the DAC utilizes a 3.5 mm minijack which connects to another minijack next to the 8200 amp's Line 2 RCA inputs, (inactivating them when it is engaged)

13th January 2019, 12:37 AM	#3
mrobertweiss diyAudio Member Join Date: Jan 2019	old instructions for the TU 8100 I read these instructions for the 8100, but it seems to me that is a different device, the minijacks on the back of the 8200 obviate the need for the shielded cable piece in the instructions you made for the 8100, if I am not mistaken. I just wanted to pull the power for the little board from the amp, rather than from the computer via usb.....seemed more efficient, although i may just be ignorant.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Some thoughts on Elekit TU-8200DX	paczeltf	Elekit	11	18th February 2019 04:18 PM
ELekit TU-8200DX (internal View)	vkung	Elekit	0	23rd January 2014 03:36 AM
Elekit TU-8200DX LED Light	vkung	Elekit	0	15th January 2014 07:00 AM
Elekit TU-8200DX	vkung	Elekit	0	11th January 2014 07:35 AM
Elekit TU-8200DX	vkung	Elekit	0	24th December 2013 06:55 AM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read

12th January 2019, 08:15 PM	#2
vkung diyAudio Member Join Date: May 2005 Location: Vancouver BC Canada	send your email address to infp@vkmusic.ca I will send you the English manual

13th January 2019, 04:48 AM	#4
vkung diyAudio Member Join Date: May 2005 Location: Vancouver BC Canada	TU-8100 requires shielded cable. TU-8200 use the 3.5mm male to male cable