Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Digital Source Digital Players and Recorders: CD , SACD , Tape, Memory Card, etc.

KSS-272A Substitution of laser diode
KSS-272A Substitution of laser diode
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 4th July 2020, 01:09 PM   #11
ManoloMos is offline ManoloMos  Spain
diyAudio Member
 
Join Date: Dec 2019
Location: Canary Islands
Quote:
Originally Posted by vt4c View Post
ManoloMos,
Thank you for sharing your excellent work. I own a CDP with KSS-151A pick-up and are looking forward to your experiment again on changing the laser diode.
Hello. I've bought some ffc/fpc 20 pin 1,25 pitch cables and connectors for the KSS-151A, I'll try to change the diode laser in an KSS-151A and I'll tell in this forum.
For the KSS-151A we have to do a little circuit, to polarizase each a-b-c-d-e-f diode separately. I have to do this circuit because in almost all CD's player with KSS-151A or KSS-190A, the A C and B D diodes are joined, we need to see these diodes serparately.
  Reply With Quote
Old 4th July 2020, 01:20 PM   #12
ManoloMos is offline ManoloMos  Spain
diyAudio Member
 
Join Date: Dec 2019
Location: Canary Islands
Quote:
Originally Posted by Salar View Post
Tried to contact Ken Klements for my laser diode swap project.
There are some photos floating arond by laser repairers
What struck me was the fact that one can see the beam spots
superimposed over the photodiode-array spots.
Maybe this effect can be used for aligning?
See photos below:
Hello. No, in fact, I doubt that in reality, the laser impact in the photodiode array be like in this picture.
If you see, almost all laser pickups has a part when you can see the A-B-C-D-E-F diodes. This makes me think that the method used in factory for to adjst the laser diodes is with a machine reading the A...F diodes. To adjust it, you have to put a mirror front the pickup, and to excite the focus coil with low frequency signal and a bit of dc voltage.

When you are triying to adjust the laser, you see that the first diodes to reach signal are E and F, then the others. Find E-F is easy, to calibrate A-B-C-D diodes is the most difficult. So, when you are triying to find the best position, you make a mental representation of how the laser are lighning the photodiodes. So, that makes me think that this pictures is a artistic representation, I don't think it be true in reality. E-F.

I hope another technician or engineers trying to do the same like I, so with more experiences, we can reach more knowledge in this issue.

In the manual service of the Pioneer P-D70 appears how to adjust the laser pickup, with an oscilloscope and a external device, this manual is the key.
  Reply With Quote
Old 4th July 2020, 02:07 PM   #13
ManoloMos is offline ManoloMos  Spain
diyAudio Member
 
Join Date: Dec 2019
Location: Canary Islands
Quote:
Originally Posted by percival007 View Post
It would have been interesting if you had reassembled the Laser Block at this point, I suspect it may have worked.

In my experience repairing CD Players, very few emitting Diodes have failed, it is usually the Receiving Diode array or more likely dust where it's ''not usually'' accessible.
You have proved that it is accessible and a good clean 'probably' cured your problem.

I slute your perseverence !!

Hello. The second KSS-272a, belongs to a CD i bought 8 or more years. It used to skip some tracks in some cds. The solution was to adjust the position of the part who contains the movil lens. This part has two screws underneath which are very difficult to adjust while the cd is playing. But adjust wasn't this screws, the screws are above, and the best performance was moving this piece to a side. This made me think that:

1 The laser pickup was bad ajusted in factory.
2 The plastic pieces were deformed, a tiny deformation, but enought for to worse the performance.

So, repair this kind of lasers is nos only to changle the laser, is necesary to adjusto, to clean and to solve any problem that could appear.

It's not easy.

The laser was replaced because the signal was a bit noise. Though the power laser was good, it seemed a bit noise and I wanted to experimentize.

When the laser gets older, it seems that besides to get weaker, the signal is noisy in the oscilloscope. I don't know why it happens.
One of the main property of the laser, is the phase cleanliness. I think maybe it appears phase noise, and without phase cleanliness, the performance get poor.
 

Reply


KSS-272A Substitution of laser diodeHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Accuphase DP65/Sony - KSS 272A laser head markaudio Digital Source 17 18th February 2019 11:59 PM
quick question about improper PS diode substitution gary h Chip Amps 3 12th January 2012 07:19 PM
laser diode petronius Parts 0 7th March 2010 08:00 PM
WTB: Sony KSS 272A laser vadimgal Swap Meet 2 24th January 2010 01:58 PM
Ultrafast Diode bridge substitution fr0st Parts 10 16th February 2003 04:00 PM


New To Site? Need Help?

All times are GMT. The time now is 01:14 PM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.00%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Copyright ©1999-2020 diyAudio
Wiki