Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Construction Tips Construction techniques and tips

attic horn subwoofer
attic horn subwoofer
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 14th April 2019, 04:11 PM   #1
Lewis Goudy is offline Lewis Goudy
diyAudio Member
 
Join Date: Apr 2019
Default attic horn subwoofer

The listening room is the master bedroom of a single story saltbox with the ridge running E/W. It is on the SE corner and the mains will be on the W wall which is 16' with an adjoining bath to the N adding 6' which flows into the BR through a 30"x74" aperture. Listener seating will be 14' from the wall but there will be live performance interiorly sometimes on top of recorded program. The BR/Bath combo reaches to the ridge line with an attached garage to the N taking up the rest, with the service panel and ground at the end.

I have two Altec Lansing 515 (no suffix, i.e. 20 ohm Hollywood) and eight RCA MI-9449 15" drivers. All have been reconed so the Thiele-Small parameters are uncertain but I can measure them.

The attic plenum has loose fiberglass to the top of the (6") joists. l can do whatever I want. I play rock organ and want concert SPL as close to the bottom as I can get, but I don't want to spend a lot of money on different drivers for the sub 20Hz region. I just want to squeeze as much as I can out of what I've got with stuff from Home Depot.

One question up front: it seems like I could get design geometry easier using plane facets with polyurethane foam fill in the corners, rather than bracing bent plywood. Is there a reason not to? I will use a tractrix with the speaker wall extending the mouth, which can include the entire ceiling if that is what is called for.
  Reply With Quote
Old 15th April 2019, 12:09 AM   #2
PRR is online now PRR  United States
diyAudio Member
 
PRR's Avatar
 
Join Date: Jun 2003
Location: Maine USA
If you have EIGHT fifteens, and a 30"x74" hole, there's little advantage in a horn.

*Maybe* for rock organ. However I think you should get a 30"x74" cut of 3/4" plywood, cut the eight holes, and try it. (I have done 500-head venues with less woofer.)
  Reply With Quote
Old 15th April 2019, 06:38 AM   #3
Lewis Goudy is offline Lewis Goudy
diyAudio Member
 
Join Date: Apr 2019
No, you are misunderstanding--the room is about 14x16 but it adjoins a bathroom about 6x12 and the doorway is 30x74. I just added that detail for completeness, it doesn't matter much. Total of ten 15" (2 Altec and 8 RCA). These are all short throw (underhung, i.e. voice coil never protrudes from the gap) drivers designed for horn enclosures with fairly low power handling (~75 WRMS) and XMAX. The idea is to frame in the horn in the attic and remove part or all of the ceiling for the mouth. I thought a reasonable throat configuration would be an elongated hexagon with the Altecs side by side facing forward and pairs of RCAs firing up and down on the near-horizontal panels with the other four loading the same volume obliquely from the sides. I know that the non-vertical mounting can cause them to take a set (they have been stored vertically and rotated 180 degrees every six months) so I will arrange it so they can be rotated periodically (T-nuts and access to them if they don't simply speak to the entire attic from the rear, which is one of the things I hoped to get advice about).
  Reply With Quote

Reply


attic horn subwooferHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Attic find AMP secant Tubes / Valves 9 26th April 2012 02:32 AM
Folded horn - volume between subwoofer cone ane th start of the horn benpalmer Subwoofers 8 9th April 2012 01:10 PM
Thorens TD124 mk1 'attic find' gopher44 Analogue Source 8 17th February 2012 11:37 PM
Repeater for attic FM antenna Alex Barnett Everything Else 2 15th April 2007 08:34 AM
TL subs in the Attic? and Triangular Cabinets ralph-bway Multi-Way 23 16th September 2002 06:22 AM


New To Site? Need Help?

All times are GMT. The time now is 12:00 AM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.79%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright ©1999-2019 diyAudio
Wiki