Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Class D Switching Power Amplifiers and Power D/A conversion

Help - TA2024 Board Trimmer Adjust
Help - TA2024 Board Trimmer Adjust
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 6th October 2019, 07:01 PM   #1
jechus26 is offline jechus26
diyAudio Member
 
Join Date: Apr 2019
Default Help - TA2024 Board Trimmer Adjust

hello, I accidentally turned the knobs of the 2 trimmers of this board, this is 2 trimmers at 50 k ohm each one, I thinking that they were input gain adjustments, but its about dc bias ajust, can someone help me to factory adjust them again) thanks everybody

mini-ta2024-computer-pc-digital-stereo-amplifier-board-dc-12v3a-power-audio-amp-diy-rs1214 imgbb.com

http://www.wolfteck.com/assets/Tripath%20TA2024.pdf
  Reply With Quote
Old 6th October 2019, 08:48 PM   #2
FauxFrench is online now FauxFrench  France
diyAudio Member
 
Join Date: Dec 2017
Location: The mountains, calm and quiet.
Hi, Turn the trimmers to about mid position. Put a couple of cheap spakers at the output of the TA2024 amplifier. Start the amplifier up with the source at the input but without any signal from the source. Put your voltmeter (2V DC range) across the two amplifier terminals that are connected to one of the speakers. Try turning one trim-potentiometer to see if the voltage at the voltmeter changes when you turn. If yes, turn the trim-potentiometer until you have a minimum of voltage at the voltmeter. If no, adjust the other trim-potentiometer for a minimum of voltage at the voltmeter. Put the voltmeter across the amplifier terminals conneted to the other speaker and adjust the voltage to a minimum. Remove the voltmeter and turn the source on/up with music. Let the amplifier play for some 30min at normal sound level (it heats up to operational temperature). Put your voltmeter in the 200mV DC range, stop the music from the source and repeat the voltage adjustments as described above. Ready to use on the good speakers!

You do this adjustment twice because the DC off-set voltage varies heavily with temperature. After second round of adjustments, the DC off-set on both channels should be less than 50mV (+ or "-" does not matter) and typically around 20mV.

Last edited by FauxFrench; 6th October 2019 at 08:52 PM.
  Reply With Quote
Old 8th October 2019, 11:11 AM   #3
jechus26 is offline jechus26
diyAudio Member
 
Join Date: Apr 2019
Hi, Thank you very much Fauxfrench, after the second ajustment, the dc off set is between (01.8 - 02.0) on 200mV DC range. I appreciate your response and I am very grateful, cheers.
  Reply With Quote

Reply


Help - TA2024 Board Trimmer AdjustHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
PGA2310 PreAmp for TA2024 board nelson_mendes Analog Line Level 3 25th November 2015 05:33 PM
Sure Electronics TA2024 board version 1.4 jackplug Class D 0 1st February 2011 05:42 PM
Tripath RB-TA2024 Board Q's HaLo6 Class D 4 4th June 2009 02:32 AM
TA2024 evaluation board opentop Class D 10 12th April 2005 11:31 PM


New To Site? Need Help?

All times are GMT. The time now is 08:41 PM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.79%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright ©1999-2019 diyAudio
Wiki