Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Class D Switching Power Amplifiers and Power D/A conversion

The New Hypex Fusion Plate amps
The New Hypex Fusion Plate amps
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 4th August 2018, 05:04 PM   #891
gnl is offline gnl
diyAudio Member
 
Join Date: Feb 2013
Had the same problem and contacted Hypex support. They can send you a special softwaretool via e-mail to solve this. You have to enter the serial number and it programs the configuration into the FusionAmp. Be careful to enter the correct serial number. It will not program a module when a serial number is present.
  Reply With Quote
Old 4th August 2018, 07:58 PM   #892
Leliks is offline Leliks
diyAudio Member
 
Join Date: Jan 2010
When switching off amp via remote there is small bump. Is this normal? very annoying

Other than that - they sound amazing. Running FA253 with Scanspeak 6600+15M+26W.

Last edited by Leliks; 4th August 2018 at 08:10 PM.
  Reply With Quote
Old 4th August 2018, 08:16 PM   #893
Shutdown98 is online now Shutdown98  Netherlands
diyAudio Member
 
Join Date: Dec 2010
Location: Zutphen, Netherlands
I have that too.
Not very annoying to me with current full range speakers. I do not use the remote much to switch power off. I have the low power mode setting to switch off the amps after 15 minutes no signal.
We will see later with the active setup.
__________________
Allo USBridge Sig > Allo DigiOne Sig > S/PDIF > Hypex FA 253 > OBL-15 with Viawave GRT-145
  Reply With Quote
Old 4th August 2018, 09:09 PM   #894
Leliks is offline Leliks
diyAudio Member
 
Join Date: Jan 2010
Another issue is Auto detection of signals. Cannot make it work with analog RCA (connected left RCA to left speaker and right RCA to right) and optical (who supposed to daisy chain).

Can you suggest correct settings for master \ slave? there is at least 4 settings - "force input", "detect signal" and a few "locks.
  Reply With Quote
Old 4th August 2018, 09:23 PM   #895
paalj is offline paalj  Norway
diyAudio Member
 
Join Date: Nov 2005
Location: Norway
Quote:
Originally Posted by gnl View Post
Had the same problem and contacted Hypex support. They can send you a special softwaretool via e-mail to solve this. You have to enter the serial number and it programs the configuration into the FusionAmp. Be careful to enter the correct serial number. It will not program a module when a serial number is present.
Thanks gnl, that was good news.
  Reply With Quote
Old 4th August 2018, 10:23 PM   #896
Shutdown98 is online now Shutdown98  Netherlands
diyAudio Member
 
Join Date: Dec 2010
Location: Zutphen, Netherlands
Quote:
Originally Posted by Leliks View Post
Another issue is Auto detection of signals. Cannot make it work with analog RCA (connected left RCA to left speaker and right RCA to right) and optical (who supposed to daisy chain).

Can you suggest correct settings for master \ slave? there is at least 4 settings - "force input", "detect signal" and a few "locks.
I have to check on that... Currently on holiday for a couple of weeks.
But i noticed also that auto start was not working when i had xlr input.
After that i always use remote to power up the amps. They do go auto off.
If you have rca source and 1 reciever, the amp connected to the reciever is master, the other one slave. The spdif from master to slave is then only for volume.

For the next firmware upgrade i would like to have a adjustable volume setting at power-up. Now the setting go with 10dB steps witch is quite big. -30dB is not loud enough, -20dB is too loud....
Would be nice to have a free adjustable field where you can put in your normal listening level.
At that point auto start at analog or digital input has to be functional.
__________________
Allo USBridge Sig > Allo DigiOne Sig > S/PDIF > Hypex FA 253 > OBL-15 with Viawave GRT-145
  Reply With Quote
Old 5th August 2018, 02:23 AM   #897
powerman is offline powerman  South Korea
diyAudio Member
 
Join Date: Jun 2005
Location: SK
Quote:
Originally Posted by Shutdown98 View Post
I have to check on that... Currently on holiday for a couple of weeks.
But i noticed also that auto start was not working when i had xlr input.
After that i always use remote to power up the amps. They do go auto off.
If you have rca source and 1 reciever, the amp connected to the reciever is master, the other one slave. The spdif from master to slave is then only for volume.

For the next firmware upgrade i would like to have a adjustable volume setting at power-up. Now the setting go with 10dB steps witch is quite big. -30dB is not loud enough, -20dB is too loud....
Would be nice to have a free adjustable field where you can put in your normal listening level.
At that point auto start at analog or digital input has to be functional.
The auto start works only when I set the start up volume to -6dB (-10dB was still too low for my system), and increase the volume of my pre-amp to -35dB and above.
  Reply With Quote
Old 5th August 2018, 02:29 AM   #898
powerman is offline powerman  South Korea
diyAudio Member
 
Join Date: Jun 2005
Location: SK
Quote:
Originally Posted by Leliks View Post
Another issue is Auto detection of signals. Cannot make it work with analog RCA (connected left RCA to left speaker and right RCA to right) and optical (who supposed to daisy chain).

Can you suggest correct settings for master \ slave? there is at least 4 settings - "force input", "detect signal" and a few "locks.
My input is analogue XLR, and master for both left/right channel, no link in between the two channels.

I set the auto start to -6dB, and increase the volume of my pre-amp to -35dB and above (depend on the loudness of the source) to trigger the auto start.
  Reply With Quote
Old 5th August 2018, 09:26 AM   #899
TimbreAudio is offline TimbreAudio  United Kingdom
diyAudio Member
 
Join Date: Dec 2016
I haven't played around too much, but if my Mac Pro is left idle, the amps switch off with auto, and don't seem to detect the optical input, so I have to switch on and off. Am I missing something?
  Reply With Quote
Old 5th August 2018, 09:39 AM   #900
ds23man is offline ds23man  Netherlands
diyAudio Member
 
ds23man's Avatar
 
Join Date: Oct 2006
Location: Hypex's doorstep
In ultra low power mode the digital inputs are not scanned in stby, in low power they are.
  Reply With Quote

Reply


The New Hypex Fusion Plate ampsHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Hypex Plate Amps madtrapper Class D 1 14th March 2014 06:21 PM
Opinions wanted on using the Hypex 2.4 plate amps? SpinMonster Multi-Way 2 3rd April 2012 09:26 AM
Hypex plate amps chatziva Class D 3 29th July 2010 04:33 PM
HYPEX plate amps Glen1 Subwoofers 0 27th January 2006 03:22 AM


New To Site? Need Help?

All times are GMT. The time now is 07:06 PM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 14.29%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
Copyright ©1999-2020 diyAudio
Wiki