Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Class D Switching Power Amplifiers and Power D/A conversion

A/B testing board for high power amps
A/B testing board for high power amps
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 30th September 2011, 02:16 PM   #1
udailey is offline udailey  United States
diyAudio Member
 
Join Date: Mar 2008
Default A/B testing board for high power amps

A buddy of mine manufactures ClassD amps. He wants to compare 3 different modules and asked if I would build a board that will A/B/C them.
The idea is obvious: 12 relays with 4 per circuit of which 2 go to each module/speaker.
I dont want to have huge pops when the relays clap together as we will probably be listening at high volume and there will be significant voltage/current potential.
Should I solve the problem with a cap from + to - of the amp output/speaker input? This would be a bit like when we put a cap across the on/off switch to remove popping. Well, visualizing it now.. with cap on on/off switch its not from + to - its just from one side of the contact to the other, so perhaps I should approach it that way.
Question is.. What value cap should I use? What rating would you suggest as these amps have kilowatt capabilities?
Thanks guys/gals
Uriah
__________________
purchase LDRs anytime Also try my Resistor Replacers or LDR based Input Selector Email me. diyldr@gmail.com
  Reply With Quote
Old 1st October 2011, 08:22 PM   #2
nigelwright7557 is offline nigelwright7557  United Kingdom
diyAudio Member
 
nigelwright7557's Avatar
 
Join Date: Apr 2008
Location: Carlisle, England
Try 100nf
__________________
PCBCAD51 download or CDROM 2019 version out now http://www.murtonpikesystems.co.uk
  Reply With Quote
Old 1st October 2011, 08:29 PM   #3
udailey is offline udailey  United States
diyAudio Member
 
Join Date: Mar 2008
.1uf is much to high. Dont mean to be daft as I do appreciate the answer. I dont know the right value, but .1uf will allow music to pass through. High frequency music but it will be audible. I need a picofarad value most likely but I dont know what value.
Uriah
__________________
purchase LDRs anytime Also try my Resistor Replacers or LDR based Input Selector Email me. diyldr@gmail.com
  Reply With Quote
Old 1st October 2011, 08:47 PM   #4
Frank Berry is offline Frank Berry  United States
diyAudio Member
 
Frank Berry's Avatar
 
Join Date: Sep 2003
Location: Midland, Michigan
You may want to think about using the relays to mute the inputs and put an 8 ohm load on the outputs of the amplifiers which are not feeding the speakers.
When selected, the amplifier input would un-mute and the output would be disconnected from the load resistor and connected to the speaker.
With no audio going through the amplifier, the output load resistors could be quite small.
__________________
Frank
  Reply With Quote
Old 1st October 2011, 08:50 PM   #5
udailey is offline udailey  United States
diyAudio Member
 
Join Date: Mar 2008
Thanks Frank. We want the same signal going to each amp full time so we can instantly switch between amps so that my audio memory isnt lost as it only takes a few seconds for me to lose the feeling of the quality of the music coming from one amp when switching to the next.
__________________
purchase LDRs anytime Also try my Resistor Replacers or LDR based Input Selector Email me. diyldr@gmail.com
  Reply With Quote
Old 1st October 2011, 08:54 PM   #6
Frank Berry is offline Frank Berry  United States
diyAudio Member
 
Frank Berry's Avatar
 
Join Date: Sep 2003
Location: Midland, Michigan
The same relay which switches the output can also mute and un-mute the input.
No delay at all.
The only other option would be to put a BIG load resistor on the output of each channel of the amplifiers which are not selected to feed the speaker.
I don't think that a capacitor on the output will provide the proper loading. Worse case would be a tuned circuit at certain frequencies.
__________________
Frank
  Reply With Quote
Old 1st October 2011, 08:59 PM   #7
udailey is offline udailey  United States
diyAudio Member
 
Join Date: Mar 2008
A cap is only to reduce the pop I expect when the relay closes. Like flicking the ON/OFF switch on your amp. Without a cap across its contacts it will arc and you will hear that arc as a pop in your speakers.
__________________
purchase LDRs anytime Also try my Resistor Replacers or LDR based Input Selector Email me. diyldr@gmail.com
  Reply With Quote

Reply


A/B testing board for high power ampsHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Fast GB: LM4702 high power amp test board ;) veteran Group Buys 150 12th March 2007 04:30 PM
selling high current power supply for power amps. ericpeters Swap Meet 0 14th January 2005 02:21 PM
high performance regulated supplies for power amps jez Solid State 14 5th January 2004 03:22 PM


New To Site? Need Help?

All times are GMT. The time now is 08:00 AM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.00%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright ©1999-2019 diyAudio
Wiki