Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Chip Amps Amplifiers based on integrated circuits

Mounting a Heatsink
Mounting a Heatsink
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 11th December 2007, 09:46 PM   #1
Bigman is offline Bigman  United Kingdom
diyAudio Member
Join Date: Nov 2007
Default Mounting a Heatsink

Hi guys,

I've just finished building my chip amp based on the LM4766. Sound is pretty good - I actually think my test speakers are letting the side down. I plan to get some decent speakers in the mix once I've built a box to move this thing.

One thing that is bothering me a bit though is how well I've mounted the heatsink.

During my testing, I can fairly easily hit the thermal overload protection. Whilst the chip is burning hot to the touch, the heatsink never reaches anything I would describe as 'hot' (though it is warm).

I can input roughly a 75% amplitude sine wave from my computer, which equates to approximately a 20V peak-to-peak output into 6ohm single-channel test speaker before it kicks in. I'm not sure how to work that out into power output, depending on how I work it out its somewhere between 8W and 33W per channel! If someone could shed some light on that, that would be great

I'm using a less-than-ideal set up for 6ohms (I designed with 8ohms in mind, and have a less-than-ideal power supply). My rails are +/-36.3V under load.

Anyway, I'm thinking that the heatsink should be getting a lot hotter than it is, and if it were dissipating the chips heat better that would improve the power headroom on my amp.

At present the heatsink is pressed up against the chip with a thermal pad between them and then glue-gunned together. I realise this solution is seriously ghetto - so fixing them together properly is my goal. One thing I am bothered to get right is having the heatsink electrically isolated from the chip, as the heatsink is going to external and so needs to be grounded like the rest of the case.

So any and all of your help, comments, suggestions etc are greatly appreciated and very welcome. Thanks in advance!
  Reply With Quote
Old 11th December 2007, 09:55 PM   #2
Dr_EM is offline Dr_EM  United Kingdom
diyAudio Member
Dr_EM's Avatar
Join Date: Oct 2006
Location: Swindon
It sounds like there may be a lack of pressure between the sink and the chip. To transfer the heat these must be pressed together very tightly so as to fill the tiny air gaps that otherwise occur. The surface of the sink must also be totally smooth and flat. Use a bolt through the mounting hole or a clamp across the chip to get the pressure needed. A "tap and die" set is needed to make a thread in the sink so that a bolt/machine screw can be driven into it.
  Reply With Quote
Old 11th December 2007, 10:10 PM   #3
Bigman is offline Bigman  United Kingdom
diyAudio Member
Join Date: Nov 2007
How can I ensure that the heatsink remains isolated if I were to screw/bolt through from the chip?
  Reply With Quote
Old 11th December 2007, 10:52 PM   #4
dark_avenger is offline dark_avenger  Australia
diyAudio Member
Join Date: Sep 2007
Silcon Washers, same as used with 3 legged regs, etc. not sure where to source them from though...
  Reply With Quote
Old 11th December 2007, 10:55 PM   #5
markiemrboo is offline markiemrboo  United Kingdom
diyAudio Member
Join Date: Mar 2006
Location: Great Yarmouth, UK
Originally posted by Bigman
How can I ensure that the heatsink remains isolated if I were to screw/bolt through from the chip?
Use 'insulating bushes' for the screws and a non-conductive pad

See: http://www.rapidonline.com/productin...moduleno=31445 and http://www.rapidonline.com/products....3=Thermal+Pads

I found that the TO3-P sized pads work for the LM series chips, though the chip does overhang at the edges a tiny bit as the pad isn't quite wide enough. This wasn't a problem for me though. The two don't touch due to the pads thickness, and the heatsink surface is also anodized which I think provides some electrical isolation.
  Reply With Quote
Old 11th December 2007, 11:12 PM   #6
seventenths is offline seventenths  United States
diyAudio Member
Join Date: Apr 2007
Location: Kingston WA>
As an aside; I have (quite successfully) been using small spring clamps to hold chips to my test heat sink. As a matter of fact, one such setup has been running for several months.


  Reply With Quote
Old 12th December 2007, 06:59 AM   #7
tangmonster is offline tangmonster  South Africa
diyAudio Member
tangmonster's Avatar
Join Date: Jul 2007
Location: Cape Town
To test my Heatsink I made up an 8 ohm load by soldering two 50W resistors in series.

Then i used a shareware program to output a 1khz sine wave out my pc and had the oscilloscope connected to the input and the output.

I am using 35.44V power rails.

I then turned the volume up until my output reached the magic 28V mark (50W into 8ohm)

The wave started to get the top and bottom cut of at higher voltage so my max was 28V before the wave got distorted.

I left it at the full output for about a minute, the load resistors started to smell and got VERY VERY hot.

Heatsink got hot , but I could easily keep my hand on it , i didn't take any temps but heatsink was not even like a hot cup of coffee.

To mount chip onto alu heatsink i drilled on 3mm hole and used anough heat paste and a small selftapper screw to bind it down.

I even used the TF version of lm3886.

My heatsink is about (150 x 53 x 50) mm finned.

  Reply With Quote
Old 12th December 2007, 01:47 PM   #8
AndrewT is offline AndrewT  Scotland
Join Date: Jul 2004
Location: Scottish Borders
Hi Big,
if the chipamp (not the heatsink) gets too hot to touch when there is no input/output signal then you need better cooling.

If the chipamp temperature rises by more than 10Cdegrees above the quiescent temperature during power delivery in ordinary listening (whether quiet or party levels) then the heatsink is not dissipating sufficient heat.

If you do any serious power testing on continuous signals then the time period must be shortened so that the chipamp never overheats. You need to allow time for everything to cool down between each test run. I normally only do half power to full power tests for <=2seconds.

20Vac into 6ohms is 20*20/6=67W.
20Vpk (sinewave) into 6ohms is 20*20/2/6=33W.
Both of these test signals will raise the chipamp temperature very rapidly.

The chipamp must be securely clamped to the heatsink to maximise the heat transfer. Clamping is recognised as better than bolting for heat transfer.

Have a thorough read of the National datasheet. If you have any queries on content come back.
regards Andrew T.
  Reply With Quote
Old 13th December 2007, 03:00 PM   #9
Bigman is offline Bigman  United Kingdom
diyAudio Member
Join Date: Nov 2007
Thanks guys,

Just for now I've reattached it with a thermal pad and got it temporarily clamped. I will do a proper job of it once I've got the appropriate bits.

It still hits the overload protection around the 12Wrms mark playing a 100Hz sine wave, which I can probably attribute to high voltage rails and a 6ohm load. However, having had a good play with it with some music, I can seriously blast it (around 75Wrms peak through my single 6ohm speaker) without any protection kicking in. In fact, when giving it that much welly, it clips the output.

To my mind, that is great if it happy playing music at over-drive state without the overloads kicking in. Having run it for quite some time, the heatsink gets fairly warm, but not hot, and the chip feels roughly the same temperature - suggesting I now have a pretty reasonable thermal contact.

Next on the to-do list is to get two speakers connected in and do similar testing. After that I'll get the nice 8ohms on it

Thanks for the helps
  Reply With Quote


Mounting a HeatsinkHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
heatsink mounting Q woodturner-fran Pass Labs 6 15th April 2008 10:00 PM
mounting of outputs to heatsink bigpanda Solid State 10 27th April 2006 11:44 AM
Help - Mounting transistor to heatsink vsr123 Pass Labs 10 17th April 2003 12:43 PM
Heatsink mounting. JoeBob Solid State 3 21st January 2002 03:51 AM
Heatsink mounting issue nikami Solid State 2 3rd April 2001 10:15 PM

New To Site? Need Help?

All times are GMT. The time now is 10:24 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.79%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Copyright ©1999-2019 diyAudio