Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Analogue Source Turntables, Tonearms, Cartridges, Phono Stages, Tuners, Tape Recorders, etc.

What does anti-skating achieve?
What does anti-skating achieve?
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 16th August 2002, 11:03 AM   #1
bm_mode is offline bm_mode
diyAudio Member
 
Join Date: Oct 2001
Location: New Zealand
Question What does anti-skating achieve?

I know anti-skating is there to prevent the cartridge from swinging in towards the centre, but why is this necessary? Would this not push the stylus up against the outer edge of the groove, emphasising that channel of the stereo at the expenxe of the channel encoded on the inner groove?

I can't hear any real difference on my turntable with anti-skating applied or not, but then again it not the greatest of turntable front-ends (Lenco L78 and a cheap ortofon cart fed into an even cheaper op-amp phono pre-amp kitset job).
  Reply With Quote
Old 16th August 2002, 03:15 PM   #2
peranders is offline peranders  Sweden
Electrons are yellow and more is better!
diyAudio Member
 
peranders's Avatar
 
Join Date: Apr 2002
Location: Göteborg, Sweden
What does anti-skating achieve?
The question has puzzled me since I was kid, never got a good answer intil now.

It's unimportant if you have a very long and (straight) arm!

If you have a completely straight tone arm, what happens if you apply a force exactly away from the suspension point? Nothing, just a force in the same direction as the arm, no skating!

But, normal arms 10-12" long must have some angle of the pickup in order to get a decent tracking error, minimum at the centre (of the engraved surface) on the LP. This angle creates a force (due to friction in the vinyl) which direction is NOT from the suspension point. One composant of the force is straight in the arm direction and the other one is towards the LP center. This force must eliminated with a contra force (force the arm out) in order to prohibit the arm to dance "jenka" over the tracks.

Did anyone understand my explaination?

The purpose of anti-skating:

1 Prevent skating, not very pleasant for the LP, or your ears.

2 Prevent wear in the inner wall of the track.

My question to the expertice: Why does a elliptical stylus need more anti-skating force than a round one?
__________________
/Per-Anders (my first name) or P-A as my friends call me.
SSR03 group buy. Sign up for interest HERE. 21 pcb's in order. 0 paid.
  Reply With Quote
Old 16th August 2002, 08:20 PM   #3
dice45 is offline dice45  Germany
diyAudio Member
 
Join Date: Jan 2002
Location: Munich, Bavaria
Ok folks,
peranders is right, but his statement is not complete.
So i take another swing on it.

Imagine a flowing river. Now hang a paddle into it. Angle different to flow direction. The river's flowing water will exert friction and stream forces on the paddle. AS the flowing direction is not aligned parallel with the paddle's blade, stream force exert a momentum trying to rotate the baddle until its blade is aligned with the flowing direction. Then the momentum becomes zero and the only forces remaining are the friction forces trying to pull the paddle out of your hand.

So: the skating force's origin (in fact the SF is a momentum referenced to tonearm pivot) is exactly the same of the momentum caused by stream forces described above. "Flowing direction" is the groove tangent thru the stylus tip. As the tonearm has a headshell with an offset angle to minimize lateral tracking error and as the phono cartridge is aligned to that heasdshell, the groove tangent has a distance to the tonearm pivot. So a momentum develops turning the tonearm towards the spindle. Like the paddle in the river.


The purpose of anti-skating:

1st
Prevent skating, not very pleasant for the LP, or your ears.

2nd
Prevent wear in the inner wall of the track.

3rd and sonically important
horizontally bias the generator system of the phono cartridge.

The phono cartridge has its cantilever suspended in rubber. This rubber acts like a pair (or quad) of highly progressive springs (and that damping is built-in is secondary for tis consideration) which menas that the sping forces rise more than linear with excursion. If now the cantilever is biased out of its center position, acceleration forces spindle-wards and edge-wards become different. Different enough to spoil sonics.

Obvious the same has to happen in vertical direction ; proper adjustment of tracking force yields in similar sonic benefits as proper AS adjustment does.

To give you a figure, actual skating force is almost constant over the tonearm's sweeping angle and it is about 8 to 10% of the tracking force.

peranders, you ask why elliptic styli have different AS forces than conical ones. I have no comprehensive answer for that. IMO each stylus has a slightly different AS force/tracking force cocktail because friction differs. According to what i described below, i would not trust any AS scale printed on a tonearm. I would trust my ears only.

Sonic mess caused by improper AS adjustment becomes apparent in microdynamics, macrodynamics, transients. Left and right channel behaves different.
I decribe below a possible approach to adjust AS by ear. But before you get lost, consider this adjustments are well audible on a top-notch TT. I have no experinece if and how the sonic changes expose themselves on a Lenco.
------------------------
(copied from an earlier JoeNet post)

short advice to adjust the cartridge:
let's presume that overhang and offset angle are already correctly aligned, estimated tracking force and skating compensation adjusted.

1. Adjust correct azimuth by slighltly turning your headshell and listen to a stereo recording how soundstage changes its size, perspective and balance or: measure the crosstalk between left and right channel: adjust so that crosstalk L=>R is *EQUAL* to R=>L crosstalk. If you find the Ortofon Test Record 0002, you can do this by ear.

2. select a mono recording with female voice (dynamic!!) and a lot happening around. Relax and concentrate.

3. Wrong vertical tracking angle (VTA) lets her voice go wider and wider as she sings louder. Real wrong VTA lets her voice go cinemascope from left to right speaker.

Adjust VTA so that the voice has the maximum focus (minimum size and maximum shape of virtual sound sources). The louder she sings/screams the smaller her mouth has to appear; this is clearly audible at the right VTA position. This optimum is very narrow: within 2/100 of a millimetre of vertical tonearm position.

4.Find the tracking force with best dynamics and micro dynamics and most believable sound colours. This optimum also is very narrow.

5. Have a rest. You may have to repeat steps 3 and 4 : you need the maximum resolution for the following.

6. Have a rest. Select a premium stereo recording. Relax and concentrate again.

7. Adjust the skating force to zero and prepare yourself for a mean experience. The right channel will not show dynamics at all; it will sit in the corner totally bored and ignoring you. The left channel will sit in its corner like an evil ghost, considering to attack you in the next moment. It will sound very dynamic in a way that numbs the left half of your body. However, the dynamics will be nightmare-like artificial.

Now you increase the skating force to a quarter and then to a half of the expected value. You will sense that the right channel comes more-and-more alive and the left channel sounds less dynamic, intimidating and artificial. This reduction is less than the increase of dynamics in the right channel; the while system becomes more dynamic. You increase now the skating compensation by *very* small steps until you reach a point where left and right channel sound equally dynamic. Then you increase further very small steps; both channels will grow more dynamic. One step too far and both channels loose their dynamics completely and sound dead. So you go back to the position where dynamics and microdynamics were maximum.

8. Note down *all* positions, scale readings, input impedances/capacitances and so on (you may want to mount another cartridge later and then find you loathe it) .

Done.

I never had the skating compensation's scale read above the
tracking force scale, always below!
Usually 60-70% of the value expected by the scale prinited on the tonearm.
__________________
Regards,
Bernhard
  Reply With Quote
Old 16th August 2002, 08:39 PM   #4
wuffwaff is offline wuffwaff  Netherlands
diyAudio Member
 
wuffwaff's Avatar
 
Join Date: Aug 2001
Location: Ingolstadt Germany
peranders,


a complete straight tone arm would have to be a linear tracking one where the pivoting point is somewhere far away (for you it probably would be in Spain)


For setting antiskating force I use a somewhat easier method (although I will try the one mentioned by Berhard).
Use a test record with a tracking test. Normally at 70, 80 or 90 mu the cartridge starts to misbehave (i.e. distort). Now I adjust the antiskating until the distortion starts at the same time in the right and left channnel.

william
__________________
een ooievaar is geen konijn want zijn oren zijn te klein!
  Reply With Quote
Old 16th August 2002, 10:38 PM   #5
dice45 is offline dice45  Germany
diyAudio Member
 
Join Date: Jan 2002
Location: Munich, Bavaria
William,

so i did before AllenWright showed me this method to do it by ear.
The test record brings you in the ball park, not more. And you never know if your test record survived the last mistracking
BTW, also the test record will disagree with the tonearm's AS scale.
And the blank band test, too; surpisingly the blank band test agrees closely with the adjustment by ear.
__________________
Regards,
Bernhard
  Reply With Quote
Old 17th August 2002, 07:17 AM   #6
wuffwaff is offline wuffwaff  Netherlands
diyAudio Member
 
wuffwaff's Avatar
 
Join Date: Aug 2001
Location: Ingolstadt Germany
Hi Bernhard,

the blank test once drove me crazy with my Lyra Lydian. The form of the needle doesn't seem to like blank tests The scale of my SME IV wasn't big enough to dial in enough antiskating.

william
__________________
een ooievaar is geen konijn want zijn oren zijn te klein!
  Reply With Quote
Old 18th July 2017, 07:15 PM   #7
Grasso789 is offline Grasso789  Germany
diyAudio Member
 
Join Date: Mar 2016
Location: Juelich
Default Skating is very variable

Spandau Ballet's drummer may be left-handed, because his ride cymbal appears on the ride side on my stereo. Without anti-skating, I could barely hear it. With strong anti-skating, it became impressive. But i think, i had too much anti-skating, and with less of it, the ride now sounds like mastered with 44 KHz sampling rate. Skating changes sound, end of the line.

I do not care for influence of modulation into skating force, because modulation is only temporary and drowns in arm inertia, or at least i have no means to handle the effect.

I assume, that skating stays the same with different tip-to-groove speeds, because friction between solid-state bodies have this Haft-/Gleitreibung issue. I also assume, that skating goes linearily with radial vector of tangent/arm parallelogram. So we have a ruffly 2 to 1 variation in static skating.

A weight on thread over a support fixed to a lever is a lame anti-skating device, because it has only that few force variation of horizontal arm angle, which is around than 1.3 to 1. Theoretically better were a spring; with proper length of spring and lever, we get much variation. Downside is susceptibility to vibration. Optimum were a magnetic device.

Last edited by Grasso789; 18th July 2017 at 07:43 PM.
  Reply With Quote
Old 18th July 2017, 07:41 PM   #8
Discopete is offline Discopete  Canada
diyAudio Member
 
Join Date: Nov 2009
Quote:
Originally Posted by Grasso789 View Post
Spandau Ballet's drummer may be left-handed, because his ride cymbal appears on the ride side on my stereo. Without anti-skating, I could barely hear it. With strong anti-skating, it became impressive. But i think, i had too much anti-skating, and with less of it, the ride now sounds like mastered with 44 KHz sampling rate. Skating changes sound, end of the line.

I do not care for influence of modulation into skating force, because modulation is only temporary and drowns in arm inertia, or at least i have no means to handle the effect.

I assume, that skating goes linearily with radial vector of tangent/arm parallelogram and linearily with groove speed. Hence skating would leap ahead some from 33 to 45 rpm. This leap due to change of revolution rate is small compared to the variations due to geometry of a common disc and turntable. Radial vector changes ruffly by two, groove speed even more, so we have a 5 to 1 variation in skating.

A weight on thread over a support fixed to a lever is a pretty lame anti-skating device, because it has only that few force variation of horizontal arm angle. Theoretically better were a spring; with proper length of spring and lever, we get much variation. Downside is susceptibility to vibration. Optimum were a magnetical device.
Imo, a table without SRA/VTA or AS adjustment on the fly is not technically up to date and hence, inferior. Tuning it like a radio while listening is the way to get it perfect with insight to the changing sq as it fades in to optimal and out with over adjustments. It's actually very simple
  Reply With Quote
Old 19th July 2017, 09:48 AM   #9
picowallspeaker is offline picowallspeaker  Italy
diyAudio Member
 
picowallspeaker's Avatar
 
Join Date: Apr 2007
I recently removed from an old Pioneer automatic ( PL-12 improved... ) all the mechanism and skating system too ( I still have all the pieces in a little box )
and it does go well - definitively better
( it still has the original Pioneer/pickering head-pickup )
__________________
Everything under and above heaven is in utter chaos
mare monstrum
  Reply With Quote
Old 19th July 2017, 10:52 AM   #10
Grasso789 is offline Grasso789  Germany
diyAudio Member
 
Join Date: Mar 2016
Location: Juelich
Default Hello

Well, pico, a weight+thread+support+lever anti-skating system is simple and can help.

I set mine such, that the needle stays centered on the end spiral of a long LP, meaning no static horizontal force. The reasoning is, that, using a spherical tip, most problems occur on the end of a LP record, where i shall get at least the skating issue rite.

Gleitreibung depends only on the force, with which both bodies are pressed together, and a material-with-material constant. Velocity not involved (except, that v>0, else it is Haftreibung), geometry not involved.

I have a Pickering, too. Rather heavy but nice.

Pete, i still edited my post, your quote contains a big mistake. Why do you mention vertical tracking angle, is this not usually fixed around 20°, while Decca had their own ideas about it, but anyway it changes only mostly channel seperation? How could one adjust that while playing that record?

If i were to really get grips with it, i would strive to be able to adjust horizontal angle more finely than I can now and have a test LP side with a static skating-detect signal (4KHz with -20dB?) from start to end.
  Reply With Quote

Reply


What does anti-skating achieve?Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
EMT 929 anti-skating weight wpod Analogue Source 4 20th February 2008 12:20 AM
Anti-skating issues ross1976 Analogue Source 6 24th December 2004 06:21 PM
Thorens 166mk2 anti-skating weight. unitgain Analogue Source 6 29th January 2004 01:41 AM


New To Site? Need Help?

All times are GMT. The time now is 08:11 PM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.79%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio
Wiki