Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Analogue Source Turntables, Tonearms, Cartridges, Phono Stages, Tuners, Tape Recorders, etc.

Technics SP-10 Doesn't Spin
Technics SP-10 Doesn't Spin
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 20th October 2014, 01:28 PM   #1
breadhead is offline breadhead  United States
diyAudio Member
 
Join Date: Dec 2004
Location: Pennsylvania
Default Technics SP-10 Doesn't Spin

Hello everyone,

I recently purchased a SP-10 MKII in "as is" condition so no complaints about the seller. It powers on and the strobe lights but that is it, no platter movement at all. I have minimal electronic experience. I have looked at the troubleshooting section here, Library Downloads - Vinyl Engine

I have taken some voltage readings but my low level skills don't allow me to interpret them, many of which are way off. Below are the readings I got:


E15 26.01V 28.18V

TR118 E 6.06V .408V
C 21.17V 28.13V
B 6.69V .121V

TR115 B .771V
C .162V

TR116 B .103V
C 6.07V

TR117 B .113V
C 6.07V .46V

D101 26V 0V

D106 6.7V 6.01V

D107 6.01V 0V


P3 20.52V

Any help would be greatly appreciated!

Thank you,
Jim
  Reply With Quote
Old 20th October 2014, 02:01 PM   #2
east electronics is offline east electronics  Greece
diyAudio Member
 
east electronics's Avatar
 
Join Date: Jan 2006
Location: Athens GREECE
Jim ...

None of the readings you posted is of any use unless you have a working SP10 open in front of you Or you have repaired at least 50 of them and you know them inside out ...

I don't think that you will find any of the above conditions in the forum easily ...

This is not a repair for a NB ,,,seek for expert help ...

The usual suspects though for direct drive Technics are
Dirty switches and bad contacts
poor soldering
Dried capacitors
But it gets even worst
IC that drive the motor
IC that produce or sensors that control the frequency

And so on and on
__________________
SERVICE ΕΝΙΣΧΥΤΩΝ ΚΑΙ ΙΑΠΩΝΙΚΩΝ ΜΗΧΑΝΗΜΑΤΩΝ ΗΧΟΥ www.eastelectronics.gr
  Reply With Quote
Old 20th October 2014, 05:44 PM   #3
Drummerboy2 is offline Drummerboy2  United States
diyAudio Member
 
Join Date: Jan 2013
Location: San Diego
make sure the motor is NOT locked down with the the transport screws in the locked down position. Also check the power supply output when cable is connected and make sure they are correct. You should be able to find that info on the vinyl engine site.

Hope this helps
  Reply With Quote
Old 21st October 2014, 09:24 PM   #4
Notinthislifetime is offline Notinthislifetime  United Kingdom
diyAudio Member
 
Join Date: Sep 2014
You need to check the supply voltages to the drive circuit. What you are looking at is the control board and from recent experience those look correct. The service manual is available from the vinyl engine and contains the voltages you should be looking for at rest, bracketed numbers and at 33.3rpm, boxed numbers.

Good luck
  Reply With Quote
Old 22nd October 2014, 01:29 AM   #5
6L6 is offline 6L6  United States
diyAudio Moderator
 
6L6's Avatar
 
Join Date: Oct 2010
Location: Denver, Colorado
Technics SP-10 Doesn't Spin
You need a digital oscilloscope or an analog scope and frequency counter to get one of them set right...

But anyway, look for leaky caps, burnt resistors, and the like, in the PSU first, then the table innards.

Take a bunch of close-up, well-lit, in-focus photos and post them here.
  Reply With Quote
Old 22nd October 2014, 11:49 AM   #6
breadhead is offline breadhead  United States
diyAudio Member
 
Join Date: Dec 2004
Location: Pennsylvania
Hello again and thank you all for your advice so far. I began to test voltages in the drive circuit but stopped after the first test as the readings were way off. I got 32.24V at a1. I tested TR38 and got these: 12.20V, 70mV, 11.47V and 12.46V, 3.5mV, 11.73V. I do have the service manual but as I stated, I am not well versed in electronics but am very capable in learning. Any help, again, much appreciated.

Thank you,
Jim
  Reply With Quote
Old 27th October 2014, 12:09 AM   #7
sgrossklass is offline sgrossklass  Germany
diyAudio Member
 
Join Date: Nov 2004
Location: Germany
There is a troubleshooting flowchart on page 6/7 which you'll want to follow (item (A)). So far you have only checked a single supply voltage (+32.5 V), which is a bit low but not worryingly so (plus I don't know how accurate your meter is).

Looks like the base connection of TR38 comes from TR127, so this one will need to be checked, followed by TR152, TR106 and TR107. Heh, the flowchart says check voltage and waveform on TR127 and TR151-154, not bad. So I guess you'll want to do that.
  Reply With Quote

Reply


Technics SP-10 Doesn't SpinHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
The Incredible Technics SP-10 Thread 6L6 Analogue Source 1176 28th November 2018 12:11 PM
Technics SP 10 Speed Problems rollinr Analogue Source 29 27th October 2017 10:05 AM
Cheap oscilloscope for setting up a Technics SP-10 johnm Analogue Source 22 28th June 2011 08:47 PM
Technics SP-10 speed problems Stefanoo Analogue Source 3 17th August 2008 11:05 PM
Technics SP-10 MKII pitch control peterb Analogue Source 6 28th March 2004 02:29 PM


New To Site? Need Help?

All times are GMT. The time now is 06:27 PM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.00%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio
Wiki